Table of Contents
Advertisement
EN 46
6.
QFU2.1E LA
Use of Alternative BOM => an alternative BOM number usually
indicates the use of analternative display or power supply. This
results in another display code thus in another Option code.
Refer to Chapter
2. Technical Specifications, Diversity, and
Connections.
6.4.4
Option Code Overview
Refer to the backcover sticker in the set for the correct option
codes.
Important: after having edited the option numbers as
described above, you must press OK on the remote control
before the cursor is moved to the left!
6.5
Reset of Repaired SSB
A very important issue towards a repaired SSB from a Service
repair shop (SSB repair on component level) implies the reset
of the NVM on the SSB.
A repaired SSB in Service should get the service Set type
"00PF0000000000" and Production code "00000000000000".
Also the virgin bit needs to be set. To set all this, you can use
the ComPair tool or use the "NVM editor" and "Setup => TV
settings => General settings => Reinstall TV" (virgin mode).
After a repaired SSB has been mounted in the set (set repair
on board level), the type number (CTN) and production code +
12NC's (SSB, display and supply) of the TV has to be set
according the type plate of the set (no info on12NC's here). For
this, you can use the NVM editor in SAM. This action also
ensures the correct functioning of the "Smart TV" feature and
access to the Smart TV portals. The loading of the CTN and
production code can also be done via ComPair (Model number
programming).
After a SSB repair, the original channel map can be restored,
provided that the original channel map was stored on a USB
6.6
Total Overview SAM modes
Table 6-9 SAM mode overview
Main Menu
Sub-menu 1
Hardware Info
A. SW version
B. Stand-by processor version e.g. "STDBY_83.84.0.0"
C. Production code
Operation hours
Errors
Reset error buffer
Alignment
White point
Ambilight
Dealer options
Virgin mode
E-sticker
Auto store mode
Option numbers
Group 1
Group 2
Store
Initialise NVM
2013-Apr-05
Alignments
6.5.1
Sub-menu 2
Sub-menu 3
e.g. "Q5551_0.9.1.0
e.g. "see type plate"
Colour temperature
Normal
Warn
Cool
White point red
White point green
White point blue
Select module
Brightness
Select matrix
Off/On
Off/On
None
PDC/VPS
TXT page
PDC/VPS/TXT
e.g. "00008.00001.15421.02239"
e.g. "44816.34311.33024.00000"
back to
div. table
stick before repair was commenced and that basic functionality
of the TV, needed for this procedure, was not hampered as a
result of the defect. The procedure of "channel map cloning" is
clearly described in the (electronic) user manual.
SSB identification
Whenever ordering a new SSB, it should be noted that the
correct ordering number (12nc) of a SSB islocated on a sticker
on the SSB. The format is <12nc SSB><serial number>. The
ordering number of the correct "Service" SSB is the one
preceded by the letter "S" in case 2 or more ordering numbers
are present on the bar code sticker.
Figure 6-1 SSB identification
Description
Display TV & Stand-by SW version and CTN serial
number
Displays the accumulated total of operation hours.TV
switched "on/off" & every 0.5 hours is increase one
Displayed the most recent errors
Clears all content in the error buffer
3 different modes of colour temperature can be
selected
LCD White Point Alignment. For values,
see Table
6-3 White tone default settings 32"
Select Virgin mode On/Off. TV starts up / does not
start up (once) with a language selection menu after
the mains switch is turned "on" for the first time (virgin
mode)
Select E-sticker On/Off (USP's on-screen)
The first line (group 1) indicates hardware options 1
to 4
The second line (group 2) indicates software options
5 to 8
Store after changing
N.A.
18310_221_090318.eps
090319
Advertisement
Table of Contents
