Table of Contents
Advertisement
XAV-W600/W650BT
(AEP, UK)
Connection/Installation
Cautions
Run all ground (earth) leads to a common
ground (earth) point.
Do not get the leads trapped under a screw or
caught in moving parts (e.g., seat railing).
Before making connections, turn the car ignition
off to avoid short circuits.
Connect the yellow and red power supply leads
only after all other leads have been connected.
Be sure to insulate any loose unconnected leads
with electrical tape for safety.
Precautions
Choose the installation location carefully so that
the unit will not interfere with normal driving
operations.
Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperature,
such as in direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a
safe and secure installation.
Note on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component's fuse amperage
rating.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
*1 Not supplied
*2 Speaker impedance: 4 – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a
wired remote control (not supplied).
For details on using the wired remote control, see
.
"Using the wired remote control" (page 36).
*5 Whether in use or not, route the microphone input
cord so it does not interfere with driving operations.
Secure the cord with a clamp, etc., if it is installed
around your feet.
*6 For details on installing the microphone, see
.
"Installing the microphone" (page 35).
*7 Such as a portable media player, game console, etc.
Making connections
If you have a power antenna (aerial) without a relay
box, connecting this unit with the supplied power
supply connection cable
may damage the
antenna (aerial).
To the car's speaker connector
1
Purple
Rear speaker
Purple/black
(right)
2
striped
3
Gray
Front speaker
(right)
4
Gray/black striped
5
White
Front speaker
White/black
(left)
6
striped
7
Green
Rear speaker
Green/black
(left)
8
striped
To the car's power connector
14
Connection
continuous power
12
Yellow
supply
power antenna (aerial) /
13
power amplifier control
Blue/white striped
(REM OUT)
switched illumination
Orange/white
14
power supply
striped
15
switched power supply
Red
16
ground (earth)
Black
To the parking brake switch cord
The mounting position of the parking brake
switch cord depends on your car.
Be sure to connect the parking brake lead (light
green) of the power supply connection cable
to the parking brake switch cord.
Parking brake switch cord
Hand brake type
*
2
See "Power connection diagram" (page 35)
for details.
To the +12 V power terminal of the car's rear
lamp lead (only when connecting the rear
view camera)
Memory hold connection
When the yellow power supply lead is connected,
power will always be supplied to the memory
circuit even when the ignition switch is turned off.
Speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms
and with adequate power handling capacities to
avoid damage.
Monitor connection
When installing a monitor for the rear seat, connect
its parking brake switch cord to the ground (earth).
Foot brake type
Subwoofer*
*
3
*
3
*
3
Power amplifier*
1
Portable audio/
*
3
video device*
1
*
7
*
3
Rear view camera*
1
*
3
Monitor*
1
*
5
*
6
from a wired remote control (not
*4
supplied)
For details, see "Making
.
connections" (page 34).
from a car antenna (aerial)
1
Advertisement
Table of Contents
