Height Adjustment - Chicco BABY HUG PRO 5 IN 1 Manual

2. Insert the central support "A2" under the joint of the
frame "A" (Fig. 2A-2B). Be sure that the product is not
at its maximum height when carrying out this oper-
ation.
3. Insert the fasteners of the seat frame "B1" into the
respective tubes on the seat structure "C" until you
hear an engagement click and the supports of the
seat "B2" into the respective slots (Fig. 3) so as to
keep the seat area horizontal.
4. Assemble the seat (seat frame "B" with seat structure
"C") on the base: insert the two tubes on base "A"
into the corresponding holes on seat frame "B" until
they click into place (Fig. 4).
WARNING: The backrest must face the height adjust-
ment pedal "I" as shown in Fig. 4A.
5. Insert tube "D" into the corresponding holes on seat
frame "B" until they click into place (Fig. 5).
6. To assemble fabric "E" line up the holes on the fab-
ric with the restraint system installed on seat struc-
ture "C". Pass the two lateral arms of seat frame "B"
through the side fabric holes (FIG. 6), insert the pins of
the arms into the holes on either side of the backrest
(FIG. 6a) until they click into place.
WARNING: Check that both arms are assembled cor-
rectly.
7. Attach fabric "E" using the two perimeter zips above
seat frame "B" (Fig. 7).
8. Pass the crotch strap and waist straps on seat struc-
ture "C" through the holes of fabric "E" (Fig. 8-8a-8b-
8c).
9. Attach the fabric "E" to the bottom of seat structure
"C", making sure to insert all of the plastic clips in the
right slots (Fig. 9-9A).
10. Fasten Hook the front safety fastener "C1" under the
seat by rotating (Fig. 10)
WARNING: When the product is used as "Crib", "Re-
clined Cradle", "Highchair" or "First Seat" configurations,
make sure that the front safety fastener "C1" is always
fastened under the seat
BOOSTER CUSHION
11. Reducer cushion "F" is ideal from birth and can be
used or removed as necessary. To attach it to the
seat, place it on the fabric, pass the crotch strap and
waste straps through the holes in booster cushion
"F" (reclined cradle configuration), (Fig. 11). In high-
chair configuration it is also necessary to pass the
shoulder straps through the holes of the booster
cushion (Fig. 11a).
TOY BAR
12. The toys can be attached to the toy bar by passing the
straps through the plastic openings on the bar (Fig.
12) and fastening the velcro.
13. Assemble the toy bar (with the light positioned to-
wards the backrest recline lever "N") by inserting its
pins into the holes in the seat frame "B" (Fig. 13).
14. To incline the toy bar in the three possible positions
press the side buttons (Fig. 14).
15. To remove the toy bar, simply lift it (Fig. 15).
WARNING: This product must only be assembled by
an adult.
WARNING: Always check that the toy bar is properly
fastened before using it.
WARNING: To prevent possible injury by entangle-
ment, remove this toy when the child starts trying to
get up on its hands and knees in a crowling position.

HEIGHT ADJUSTMENT

16. Once assembled, the product can be adjusted to var-
ious heights in all configurations. To adjust its height,
hold down height adjustment pedal "M" (Fig. 16)
and lift or lower the seat to the desired height.
ADJUSTING THE BACKREST
17. The backrest can be adjusted to four different po-
sitions. To carry out this operation, slide the central
button "N1" downwards and then rotate the han-
dle "N" upwards, keeping the central button "N1"
pressed (Fig.17).
• Position 1 – Crib configuration / Crib Detachable from
Frame Configuration (Fig. 17A)
• Position 2-3 – Reclined cradle configuration (Fig. 17B)
• Position 4 – Highchair and First table seat configura-
tion (Fig. 17C)
These adjustments can also be made with your child
seated in the product. In this case it will be slightly more
difficult.
WARNING: Always check that the backrest is properly
locked before use.
USING THE SAFETY HARNESS
18. With fabric "E" assembled on seat structure "B",
there will be a crotch strap, two waist straps and two
shoulder straps (Fig. 18).
19. CRIB CONFIGURATION
WARNING: Completely remove all safety harnesses
making sure to keep them out of the reach of your child
(Fig. 19).
20. CRIB DETACHABLE FROM FRAME CONFIGURA-
TION
WARNING: Completely remove all safety harnesses
making sure to keep them out of the reach of your child
(Fig. 19).
To remove the crib from the frame, first of all you need
to release the front safety fastener "C1" (Fig. 20); then
press the 2 buttons "O" (Fig. 21) and, once the crib has
been released, lift it using the relevant handles "P" (Fig.
22).
WARNING: Do not lift the crib by the toy bar.
WARNING: When you lift the crib, make sure to grasp
the handles (P) diagonally, as shown in Fig 22.
WARNING: Once removed, place the crib on a flat sur-
face
WARNING: Once the crib has been removed, the back-
rest must not be reclined
21