Height Adjustment - Chicco Next2Me PopUp Manual

are securely engaged before use.
• WARNING: When the product is
being used, the wheels must al-
ways be locked.
• All operations for opening, adjusting,
fastening and positioning the prod-
uct must be carried out by an adult.
• Infants can suffocate on soft bed-
ding. Avoid placing pillows or simi-
lar items under newborn babies for
additional comfort during sleep.
• Use the crib in "Side sleeping con-
figuration (fastened to the bed)"
only with beds of the size indicted
in the reference figure at the begin-
ning of the manual.
• Do not leave anything inside
the product that might reduce its
depth.
• To prevent the child from being
trapped, do not place the crib
close to walls or obstacles.
• Do not leave any objects that
might be swallowed inside the
product.
• Do not make adjustments to the
product when the child is in it.
• Do not move the product when
the child is inside.
• Do not use the product with
more than one child at a time.
• Prolonged exposure to sunlight
may cause the colour of the prod-
uct to vary in tone. After prolonged
exposure of the product to high
temperatures, wait a few minutes
prior to putting your child in it.
• WARNING: During use, make sure
that the parent's bedsheets,
blankets, etc. do not invade the
crib space.
• Keep the product out of reach of
children when it is not in use.
COMPONENTS
A. Front barrier tube
B. Rear feet
C. Crib frame
C1. Height adjustment buttons
C2. Height indicator
C3. Closure release lever
C4. Support for barrier attachment
C5. Articulated front feet
C6. Front foot release button
C7. Wheels with brakes
C8. Barrier release button
C9. Straps with buckles for fastening the crib to the bed
C10. Rear foot release button
D. Fabric
D1. Zip fasteners for opening the barrier
D2. Upper zip fastener
D3. Fabric straps with automatic buttons
E. Mattress with removable lining
F. Fastening straps
F1. Fork 1
F2. Fork 2
F3. Buckle
G. Bag
H. Instruction Manual
ASSEMBLING THE CRIB FOR THE FIRST TIME
The product is delivered closed and partly assembled.
1. Open the frame by taking hold of the upper tubes and
pulling upwards (Fig. 1). Should the mattress keep the crib
from opening completely during initial assembly, remove the
mattress and pull the tubes upwards once again. Verify that
the locks were properly engaged by ensuring that the red
sign on the legs of the crib is not visible (Fig. 2).
2. Assemble the rear feet "B" on the back of the crib by
inserting them in the tubes until a click is heard (Fig. 3-4). Be
sure that the type of foot assembled matches the type used
on the front of the crib (with or without wheels).
3. Insert the tube for the front barrier "A" using the slots on the
fabric (Fig. 5).
4. Lift the tube "A" and attach it to the connections on the crib
(Fig. 6).
5. Close the zip fasteners "D1" on either side (Fig. 7)
6. Block the 2 wheels of the crib by lowering the levers that
activate the brakes (Fig. 8).
The product is now ready to be used as a traditional crib (with
the barrier closed).
WARNING: Make sure that all the fasteners are engaged
correctly and that the zippers are closed and locked at the end.
WARNING: Do not use the crib with the front articulated feet
partially or completely turned or released (fig. 9). The position
of correct use is illustrated in figure 10. In the case of accidental
knocking against the articulated feet, put them back in the
correct position by lifting the crib slightly.

HEIGHT ADJUSTMENT

The height of the crib can be adjusted in 6 different positions.
7. To adjust the height press up on the adjustment buttons
"C1" and raise or lower the crib until the desired position is
reached (Fig. 11). The base of the crib can be slightly inclined
by adjusting the leg supports to different heights (Fig. 12).
15