Table of Contents
Advertisement
HCD-DZ285K/DZ290M/DZ585K/DZ590M/DZ685K/DZ690M
60: Focus on error
61: Seek fail error
62: Read Q data/ID error
70: Lead in data read fail
71: TOC read time out (CD)
80: Can't buffering
81: Unknown media type
6-4-1. Clear the Laser Hour
Press [
DISPLAY] button and then press [CLEAR] button on
the remote commander. The data for both CD and DVD data are
reset.
Emg. History Check
Laser Hours
CD
DVD
01. 01 05 04 04
00 00 00 00
02. 02 02 01 01
00 00 00 00
[Next]
Next Page
[Prev] Prev Page
[O] Return to Top Menu
6-4-2. Clear the Emergency History
Press [DVD TOP MENU] button and then press [CLEAR] button
on the remote commander. The error code for all emergency history
would be reset.
Emg. History Check
Laser Hours
CD
DVD
01. 00 00 00 00
00 00 00 00
02. 00 00 00 00
00 00 00 00
[Next]
Next Page
[Prev] Prev Page
[O] Return to Top Menu
6-4-3. Clear the Initialize Setup Data
Press [DVD MENU] button and then press [CLEAR] button on the
remote commander.
Emg. History Check
Laser Hours
CD
DVD
initialize setup data...
[Next]
Next Page
[Prev] Prev Page
[O] Return to Top Menu
18
0h
0min
0h
0min
00 92 46 00
00 00 23 45
00 A9 4B 00
00 00 23 45
999h
59min
999h
59min
00 00 00 00
00 00 00 00
00 00 00 00
00 00 00 00
999h
59min
999h
59min
6-4-4. Return to the Top Menu of Remocon Diagnosis
Menu
Press [0] button on the remote commander.
6-5. CHECK VERSION INFORMATION
To check the version information, please follow the following
procedure.
(1) From the Top Menu of Remocon Diagnosis Menu, select "4.
Version Information" by pressing the [4] button on the remote
commander. The following screen appears on the on-screen
display.
Version information
Firm (Main) : Ver. xxxxx
Firm (Sub) : xxxxx
RISC :
xxxxx
8032 :
xxxxx
Audio DSP : xxxxx
Servo DSP : xxxxx
Phy,Adr,
: F,F,F,F,
[O] Return to Top Menu
To return to the Top Menu of Remocon Diagnosis Menu, press
[0] button on the remote commander.
7. D.C.A.C. (AUTOMATIC ACOUSTIC FIELD CALIBRA-
TION) TEST MODE
Procedure:
?/1
1. Press the [
] button to turn the power on.
2. Press the [FUNCTION] button to set the function " DVD".
3. Insert Calibration mic (ECM-AC2) supplied as an accessory
into the AUDIO IN/A.CAL MIC jack.
x
4. While pressing the [
] and [
the [VOLUME] control in the direction of (–).
5. Confi rm that the following are shown on the display panel.
1 The JACK inserted/non-inserted detection display and the
STEREO/MONO detection display.
2 Presence of DIGITAL voice input to the microcomputer.
(OK: input, NG: no input)
3 The AD value of the MIC input to the microcomputer.
(shown "255h")
"NON" : Not detected
"ST"
: STEREO
"MN"
: MONO
OK : input
NG : no input
0-255 (Changes in real time)
6. To exit from this mode, press the [
neously, turn the [VOLUME] control in the direction of (–).
Z
] buttons simultaneously, turn
x
Z
] and [
] buttons simulta-
Advertisement
Table of Contents
