Advertisement
'Tune in to a radio station.
ress the @ REC button on the Unit.
The PLAY buttonis pressed-at.-the
same time;the
"R
cator lights up, and the Unit begins recording.
¢
For RC-QN3, recording is done in-the following manner.
]. One side (side A for example) is recorded. The FWD
(<I) direction indicator lights up.
2.
When the tape reaches its end, the other side (side B) is
played (not recorded onto). The REV (>) direction
indicator lights up. (You should press the m/4& STOP/
EJECT button to. stop.the tape.).
3. At the tape end,
the tape stops-
¢
On model RC-QN2, the tape is recorded and then stops
when it reaches the end.
¢
The TAPE indicator turns to the right during Playback and
Recording, even in Pause mode.
To pause the recording, press the PAUSE button on the Unit.
(RC-QN? only)
To cancel pause, press the PAUSE button again. Recording con-
tinues from the point where it was paused. (RC-QN2 only)
To stop recording,
press the m/4&.STOP/EJECT button.
To remove the tape, stop the tape, and press the @/4 STOP/
EJECT button again to open the cassette holder.
T GUT)
When recording an-AM broadcast, beats. may: be produced which
are not heard when listening to the broadcast. If this happens, you
can use the BEAT CUT function.
Switch the BEAT CUT switch on
the
ba g a
@ ef the
Useit
trom
the.
;
NORM-1 to 2 or 3.
Note: In regular use, the BEAT CUT switch
should be set to the NORM-1| position.
BC" indi-
The CD Player can be started with the Cassette Deck for synchro-
nous recording and everything on the CD recorded onto the tape in
the order it is on the CD.
Deck and wind
past the leader tape.
*
On model RC-QN3, be sure that the FWD (<I) direction
indicator is lit and the tape is wound for forward playback.
(Refer to the tape insertion illustration mentioned above.)
If the REV (>) direction indicator is lit, press the DIREC-
TION button to correct it.
Load a CD.
Press the CD >/
button..
¢
You can check the: samen of tracks and the total playback time
of the CD on the display. (See page 6.)
desi reel
To select the Repeat mode (C> or C ALL), press the RE-
PEAT button on the Remote Control.
to have approx. four sec-.
between tracks.
if you want the blank sec tion, Skip this step.
If you do not want the blank section, perform the follow-
ing operation on the CD Player.
e
Press the CD »/#1 button twice.
RC-QN1/QN2/QN3
ss the @ REC button on the ee
'The PLAY button ie pressed at the same-ti
REC I
cator lights up, and the synchronous recording. be begins:
¢*
On model RC-QN3, recording happens as follows. (Note: you
will need to press
the 1/4 STOP/EJECT button when record-
ing has finished for the first side of the tape.
*
One side (side A for example) is recorded -- When the tape
reaches
its end, the other side (side B) is played back (not
recorded). — At the end of the tape (side B), the tape stops.
*
Onmodel RC-QN2, the tape is recorded and then stops when it
reaches the end.
¢
To continue recording to the other side of the tape, perform the
following steps.
1. Reverse the cassette tape and wind past the leader tape.
2. Press the CD »/IE button and then press the @ REC button.
Then, the synchronous recording begins from the beginning of the
last track that was stopped at the end of the first side of the tape.
To stop recording, press the @/4 STOP/EJECT button.
To remove the tape, stop the tape, and press the @/& STOP/
EJECT button again to open the'cassette holder.
Notes:
°
If the CD reaches its end before the tape, the tape will continue
to run until stopped. Press M®/4 STOP/EJECT button to stop
the tape.
*
During synchronous recording, the CD P/N, Ké<@, and >!
buttons for the CD Player do not function.
¢
If you press the @ REC button during playback the CD, record-
ing will start from the beginning of the track being played.
To Continue Rec crane: t to the. eener
On model RC-QN3:
After pressing the @/4 STOP/EJECT button to stop synchronous re-
cording
when recording has finished for the first side of the tape, car-
ry out the followimg to continue recording to the other side of the tape.
1]. Reversethe cassette tape and wind past the leader tape.
2. Be sure that the FWD (<)) direction indicator is lit, and
then press the @ REC button again.
The synchronous recording will begin from the last track
that was stopped at the end of the first side of the tape.
On model RC-QN2:
When the tape reached its end and stopped, carry out the following
to continue.recording to the other side of the tape.
1. Reverse the cassette tape and wind past the leader tape.
2.
Press.the @ REC. button again.
The synchronous recording will begin from the last track
that. was stopped at the end of the first side of the tape.
1-23
Advertisement
