Denon DCD-3520 Service Manual page 8

C3] Returning to the beginning of the
current track during playback .........0..00.0 Automatic Search
(144)
Press the Automatic search reverse button ( 1€4@ ) during playback.
e The pickup will return to the beginning of the current track and playback
will continue. Pressing the button several times will return the pickup
the corresponding number tracks.
4] Audible quick search ooo... ccc cece ceeeeseeeeeeeeeees Manual Search
® Using this function, you can cue to a desired point within a track, either
in the forward or reverse direction.
e Release the manual search button ( €4 or PP ) when the desired point
has been reached. Normal playback then continues.
(1) Manuat Search Forward
( >>)
1. Press the manual search forward button { PP) during playback.
Playback of the track is sped up.
e Asa reference, the current track number and elapsed playback time
within the track are displayed.
e Ifthe manual search forward button ( >> ) is kept pressed after the end
of the final track on the disc is reached, (?7) is displayed and manual
search stops. To return to another point, press the manual search
reverse button ( €@ ) until (723) disappears.
(2) Manual Search in Reverse
(44)
1. Press the manual search reverse button ( €@) during playback.
Reverse playback of the track is sped up.
e Asa reference, the current track number and elapsed playback time
within the track are displayed.
e@ Manual search in reverse is approximately three times faster when
engaged during the pause state compared to playback. However, in this
case, no sound is heard.
e (f the manual search reverse button ( €€ ) is kept pressed after the
beginning of the first track on the disc is reached, (CC) is displayed and
manual search stops. To return to another point, press the manual
search forward button ( PP ) until (Ci) disappears.
(5) Playing Specific Tracks in a
Specific Order
With this function, you can choose any of the tracks on the disc and
program them to play in any order.
Programming ts possible with the disc holder open.
Up to 20 tracks can be programmed.
The programmed tracks are shown on the calendar
Programming
PROG / DIRECT (Number buttons)
Press the PROG/DIRECT button so that the | PROGRAM | indicator
lights, then use the number buttons and the +10 button to program the
tracks.
For example, to program tracks 3, 12, and 7, press |PROG/DIRECT], [3],
[4707], [2], and [7].
The corresponding track number lights on the calendar each time a
track is programmed, the track number is displayed in the TRACK NO.
display, the number of tracks programmed is displayed in the INDEX
display, and the total playing time of the programmed tracks is
displayed in the TIME display. A few seconds after the last track has
been programmed, the total number of tracks programmed is display-
ed in the TRACK NO. display and the total playing time of the
programmed tracks is displayed in the TIME display.
The program will remain in the memory for approximately 2 days, even
if the power is turned off after setting the program or during program
playback.
NOTE:
e
e
e
(2)
Leave the power on for at least 10 minutes to fully charge the memory
power supply. If the power is only left on a short while, the memory will
be cleared that much sooner.
It is not possible to program more than 20 tracks.
The remaining time per track will only be displayed for the first 20
tracks on the disc.
The total programmed time and the remaining time for the program
will also not be displayed if track number 21 or greater is programmed.
Checking Programmed Tracks
DIRECT Remote control unit
CALL
Cs
a
OSPLAY TIME SEARCH ALL -REPEAT-1 |
cI Co
CLEAR TIME. "UT0 SPACE AUTO ED
(om
| 3 _)
Press the CALL button.
The programmed tracks are displayed in order in the TRACK NO.
display each time the CALL button is pressed.