Timer-Controlled Playback - Denon DCD-3520 Service Manual

e When the 1-track repeat button (REPEAT-1) is pressed in the stop mode,
track number 1 lights on the calendar and the 1 track repeat function is
possible. To start, press the ( ® PLAY) button.
« To cancel 1-track repeat, press the 1-track repeat button (REPEAT-1)
once again. Normal playback will resume.
ri 1) Playing a desired time or interval «0.00.00... eee Time Search
e With this function you can specify the starting time and/or ending time
in seconds, allowing playback of a very specific section of a track.
In the Stop Mode
Specifying the starting time
' Press the TIME SEARCH button. The indicator will
flash on the display, and the TRACK display will read "--".
Use the number buttons to set in order the track number and the time
(minutes and seconds).
Example: Starting from 2 minutes 34 seconds into track 3
Press the following buttons in order: [ TIME SEARCH J], [0], [3], [0]. (2),
(3), 4.
NOTE: If a track number or time not on the disc is set, the unit will
return to the mode it was in before the first buttons were pressed.
3) Press the ( ® PLAY) button to begin playback from the specified time.
e Specifying the ending time
The ending time can be set before pressing the play button while
the L TIME SEARCH | indicator is flashing using the following proce-
dure:
'4: Press the TIME SEARCH button. The indicator will
stop flashing and the TRACK display will read "--".
(5) Use the number buttons to set in order the track number and the time
(minutes and seconds).
NOTE: It is not possible to set an ending time at a point before (or the
same as) the starting time.
6) After specifying the ending time, press the ( ® PLAY) button to begin
repeated playback between the two specified points. (A-B repeat by
specifying the time)
W In the Play Mode
(1! When the TIME SEARCH button is pressed, the current track number
and time (minutes and seconds) are stored in the memory and the
indicator begins flashing.
(2 When the ( ® PLAY) button is pressed, playback starts from the
starting point stored in the memory.
To start playback over from the specified point, press the ( ® PLAY)
button again.
(3) If the TIME SEARCH button is pressed again, the ending time is stored
in the memory, the indicator stops flashing, and the
interval between the starting point and ending point is played
repeatedly. (A-B repeat)
To cancel the time search function, press one of the following buttons:
(1) PROGRAM/DIRECT
(2) DIRECT (on remote control unit)
(3) OPEN/CLOSE
NOTE:
e If the search function is used after a track number and time (minutes
and seconds) are specified with the disc holder open and no disc set,
playback will start from the beginning of the first track on the disc.
e If atime over the time on the disc is specfied, playback will start from
the beginning of the track following the specified track.
fey
10
® inserting blanks between tracks 0 ee Auto Space |
(
TIMER-CONTROLLED PLAYBACK
This is convenient feature that will insert 4-second blanks between
tracks, which can be used when recording compact discs on tape.
| Pay mee] foROGRAN
p]} CI Coco
aU PALSE as ee |} oncct
> PLAY) Co Cc) aj
[ INDEX CALL
Ls oo
OSPLAs TIMESEAACR «ALL -REPEAT 1
co co oO
CLEAR TIME. 3.70 SPACE AuTO EDT Remote
cy Co Le | control unit
(AUTO SPACE)
Pressing the auto space button (AUTO SPACE) will cause the
AUTO SPACE ] indicator to light.
Press the play button { ® PLAY) to start playback.
When a track has been played to its end, a 4-second silence is made
before the next track starts playing.
Press the auto space button (AUTO SPACE) again to cancel the
function.
a Operation
1. Turn on the power of all system components.
2. Set the input selector on the amplifier to correspond to the input the
CD player is connected to.
3. Make sure a disc has been loaded in the disc holder.
4. Check the time on the timer and then set the desired turn-on time.
5. Turn the audio timer ON.
Power is turned off automatically in all components connected to
the timer.
6. When the preset turn-on time is reached, power is turned on in the
system components, and CD playback starts from the first track.
NOTE:
The program will remain in the memory even if the power is turned off after
setting the program or during program playback, After approximately two
days, however, the program memory is cleared, reset the program, as
necessary.
Connection
DCD-3520
Audio Timer,
sold separately Power supply outlet
Sony arrive rnc norte ise oa Rey CPST A ORR ETRE
: pore eee anes ones ree
|