Table of Contents
Advertisement
GFK-2738AE
Release History
Version
IC695PNS001-BHBF
IC695PNS101-AFAD
IC695PNS001-BHBF
IC695PNS101-AFAD
IC695PNS001-BHBF
IC695PNS101-AFAD
IC695PNS001-BGBE
IC695PNS101-AEAC
IC695PNS001-BGBE
IC695PNS001CA-
BGBE
IC695PNS001LT-BGBE
IC695PNS101-AEAC
IC695PNS101CA-AEAC
IC695PNS101LT-AEAC
IC695PNS001-BFBE
IC695PNS101-ADAC
IC695PNS001-BFBE
IC695PNS101-ADAC
IC695PNS001-BFBE
IC695PNS101-ADAC
IC695PNS001-BDBE
IC695PNS101-ACAC
2
IC695PNS001-BDBE
IC695PNS101-ACAC
IC695PNS001-BBBD
IC695PNS101-AAAB
IC695PNS001-BBBC
IC695PNS101-AAAA
IC695PNS001-BBBB
IC695PNS001-BABB
IC695PNS001-BABA
Firmware
Date
Revision
3.41
Jan 2024
3.40
May 2023
3.36
Sep 2022
3.35
July 2022
3.30
Oct 2021
3.30
May 2021
3.26
Jan 2021
3.25
Sep 2020
3.25
Mar 2020
3.20
Oct 2019
3.15
Oct 2018
3.10
Aug 2018
3.01
Jan 2018
3.01
Aug 2017
3.00
Feb 2017
Comments
Manufacturing component issues.
MRP Fiber SFP Ring break detection during a single fiber break
Support for -JC or later backplanes
Manufacturing component issues.
Adds support for MODBUS Master and Slave exchanges using up to
four IC695CMM002/004 RX3i Serial Communications Modules.
Adds support for the IC695PSD180 Multifunctional 24VDC 80W
Power Supply.
The product's labels have been updated to show compliance with
new certifications.
For updated certifications, please refer to
mas.my.site.com/communities/en_US/Article/Certifications-and-
Agency-Approvals-Landing-Page.
Enhances Sequence of Events recording to support up to five
PNS101s when used with the IC695CPE330 64MB CPU w/Ethernet,
IC695CPE400 64MB Rackless CPU, or IC695CPL410 64MB
Rackless CPU. This release also resolves the issues found in
Problems Resolved by this Revision
Resolves quality issues.
Manufacturing update. No change to fit, form, or function.
Adds support for Sequence of Events capture from IC694MDL655
modules in the PNS101 rack.
Resolves issues described in the section entitled Problems Resolved
by this Revision
Added support for the IC694MDL730 & IC694MDR390, rebranded
the PNS001/PNS101 and GSDML to Emerson, and applied patches
for VxWorks URGENT/11 vulnerabilities.
Resolves issues described in the section entitled Problems Resolved
by this Revision.
Updates to enhance cyber security.
Initial release of the IC695PNS101 Advanced PROFINET Scanner.
Added support for the IC695HSC304 High-Speed Counter Module
with 4 Counters.
Hardware change increases isolation between Earth ground and
signal ground. Removes incorrect statement in IPI revision N
regarding RX3i backplane compatibility.
Addresses issues with SDcard communication on some assemblies.
New hardware platform with a new layout of front panel LEDs and
Ethernet connector replaces front-panel USB for firmware update.
Jan 2024
https://emerson-
5
Advertisement
Table of Contents
