Table of Contents
Advertisement
Quick Links
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Siren, L.E.D.,
Power, Ground, Doorpin, etc.
-OPTIONAL: These are features to be connected only if desired or agreed upon by the installing dealer (i.e. Door
Locks, Starter Kill, Hood, Trunk, and Auxiliary Remote Output etc.) Optional features may require extra parts and/or
labor to install.
TECH SUPPORT
Mon-Fri 8:00 AM -4:30 PM Pacific Time
(800) 998-6880
www.crimestopper.com
email@crimestopper.com
BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS,
ABS BRAKES, AND BATTERY).
TO PREVENT A POSSIBLE DEAD BATTERY remove vehicle dome light fuse while working on the vehicle. MAKE
CERTAIN TO REINSTALL FUSE PRIOR TO TESTING FOR DOOR TRIGGERS.
DO NOT EXCEED MAXIMUM OUTPUT RATINGS! - SERIOUS DAMAGE MAY OCCUR. LIMITS FOR ALARM
FUNCTIONS ARE LISTED WHERE APPLICABLE. IF UNSURE ABOUT CURRENT LOAD, MEASURE LOAD WITH
AN AMP-METER.
REMOVE MAIN SYSTEM FUSE(S) before jump starting the vehicle or charging the battery at high boost.
CS-2100
REMOTE CONTROL ALARM SYSTEM
INSTALLATION & OPERATING INSTRUCTIONS
This device complies with FCC Rules part 15. Operation is subject to the following
two conditions: 1) This device may not cause interference, and (2) this device
must accept any interference that may be received, including interference that may
cause undesired operation. The manufacturer is not responsible for any radio or
TV interference caused by unauthorized modification to this equipment. Such
modification could void the user's authority to operate the equipment.
INSTALLATION CAUTIONS & WARNINGS
Advertisement
Table of Contents
Related Manuals for CrimeStopper CS-2100
Summary of Contents for CrimeStopper CS-2100
- Page 1 AN AMP-METER. REMOVE MAIN SYSTEM FUSE(S) before jump starting the vehicle or charging the battery at high boost. CS-2100 This device complies with FCC Rules part 15. Operation is subject to the following two conditions: 1) This device may not cause interference, and (2) this device must accept any interference that may be received, including interference that may cause undesired operation.
-
Page 2: Component Mounting
COMPONENT MOUNTING DO NOT mount the control unit in the engine compartment. DO NOT Mount the control unit or wiring harness where they can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column. The alarm control module should be mounted in a concealed location. The antenna wire should be routed away from any metal if possible. - Page 3 WIRING VIOLET WIRE: (+) DOOR TRIGGER INPUT Same as GREEN wire [below] except this wire is used for vehicles that show a positive voltage (12 volts) when the door is open such as many Ford, Lincoln, Mercury vehicles. BLUE WIRE: (-) HOOD/TRUNK INPUT This wire is an input trigger for a grounding hood or trunk pin switch.
-
Page 4: Transmitter Programming
4 PIN SENSOR PLUG: WHITE WIRE: NEG. WARN AWAY BLUE WIRE: NEG. TRIGGER BLACK WIRE: SENSOR GROUND RED WIRE: SENSOR +12V POWER SILENT ARMING /DISARMING The system can be silently armed and disarmed as normal with but with no siren chirp. Turn ignition on and press the #2 Button for about (3) seconds. -
Page 5: Option Chart
Option # Option Description Passive Arming Autolock with Ignition Double Unlock Pulse Dome Light Timer Door lock pulse Carjack Lock when Passive Arming Restore Options to default ACTIVE ARMING To arm the system, press the #1 button on the transmitter. You will hear a single siren chirp and the lights will flash once. - Page 6 OPERATION EMERGENCY OVERRIDE/ VALET MODE If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to perform an Emergency Disarm. Open the door with the key, which will activate the alarm, turn the ignition ON, and press the override/program button about 3-4 seconds.
-
Page 7: Power Door Lock Wiring
POWER DOOR LOCK WIRING... - Page 8 START WIRE STARTER (-) NEG. LOCK OUTPUT BLUE/WHITE (-) NEG. UNLOCK OUTPUT WHITE/RED (+)POSITIVE DOOR VIOLET PIN SWITCH (+) DOOR TRIGGER CS-2100 WHITE BLACK CHASSIS GROUND (+) 12V POWER INPUT BROWN + SIREN OUTPUT BROWN/WHITE (-) NEG. HORN HONK YELLOW (+) POS.