Table of Contents
Advertisement
Quick Links
CONGRATULATIONS on your choice of an "On-Guard" Remote Alarm System by Crimestopper Security
Products Inc. This booklet contains the information necessary for installing, using, and maintaining your alarm
system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the
Tech Support number below.
*IMPORTANT INFORMATION: Primary and Optional Features:
-PRIMARY: These are features that must be connected in order for the system to operate properly; i.e. the
Siren, L.E.D., +12V Power, Ground, Door pin, Flashing lights Override/Program/Valet Button etc.
-OPTIONAL: These are features to be connected if desired or agreed upon by the installing dealer. These
features may also require additional parts and/or labor fees. Consult with your installer beforehand; i.e. Door
Locks, Starter disable, Hood/Trunk trigger, and Auxiliary Remote Outputs etc.
This installation book is designed for the installer or individual with an existing understanding of automotive
electrical systems, along with the ability to test and connect wires for proper operation. To ease installation,
we suggest that you READ THIS MANUAL before beginning your installation. This book is provided as a
GENERAL GUIDLINE and the information contained herein may differ from your vehicle.
TECH SUPPORT
Mon-Fri 8:00 AM-4:30 PM Pacific Time
(800) 998-6880
REV. C 2-07-2007
CS-2000DPII TW2
With 2-Way Data Port Technology
2-WAY REMOTE CONTROL ALARM SYSTEM
INSTALLATION & OPERATING INSTRUCTIONS
INTRODUCTION
This device complies with FCC Rules part 15. Operation is subject to
the following two conditions: 1) This device may not cause interference,
and (2) this device must accept any interference that may be received,
including interference that may cause undesired operation.
manufacturer is not responsible for any radio or TV interference caused
by unauthorized modification to this equipment. Such modification
could void the user's authority to operate the equipment.
The
Advertisement
Table of Contents
Related Manuals for CrimeStopper CS-2000DPII TW2
Summary of Contents for CrimeStopper CS-2000DPII TW2
- Page 1 CONGRATULATIONS on your choice of an “On-Guard” Remote Alarm System by Crimestopper Security Products Inc. This booklet contains the information necessary for installing, using, and maintaining your alarm system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number below.
-
Page 2: Table Of Contents
TABLE OF CONTENTS Installation Cautions & Warnings..…….……………………………….……………………………………….……2 Control Module & Component Mounting ……………...……………………..……………………….…….…..…..3 Wiring (LED, PROGRAM BUTTON AND SHOCK SENSOR page 5-6)…………………..………….….…..….3-6 Power Door Lock Wiring……………………………………………………….………………………….…...….…6-7 Data Port Diagram ………………………………………………………………………………………………….……8 Transmitter Programming (2 Vehicle programming)..……………………………………………….……...…9 Option Programming…………………………………………….…….………………….…….…………...….…10-12 Programmable Option Reset ………………………………….…………………………….……………...……..…13 Custom Personal Override Code …………..………………….…………………………….…………….……..…13 Operating Instructions (Sidekick Remote and 2-Way LCD Quick guide Functions page 15-16) .…...14-19 Car Jack Protection Features .…………..……………………………………………...…………………..…….…20... -
Page 3: Control Module & Component Mounting
CONTROL MODULE & COMPONENT MOUNTING DO NOT Mount the control module in the engine compartment or where the wiring harness can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column! The alarm control module should be mounted in a concealed location. The Placement of the module will affect the distance from which the remote transmitter can control the unit. -
Page 4: Wiring (Led, Program Button And Shock Sensor
WIRING BLACK WIRE: SYSTEM CHASSIS GROUND The Black wire MUST be connected to the CHASSIS METAL of the vehicle. Scrape away any paint or debris from the connection point and use a star washer to ensure a good connection. Keep the ground wire short. YELLOW WIRE: IGNITION SWITCHED “ON”... - Page 5 WIRING BLUE/WHITE WIRE: NOT USED BROWN WIRE: (+) SIREN OUTPUT (3 Amp Max.) Connect to RED siren wire from the Siren in the engine compartment. WHITE WIRE: +12V FLASHING PARKING LIGHT OUTPUT Connect to the switched parking light wire at back of light switch. If this is not possible, connect directly to one of the parking lights at the front of the vehicle.
-
Page 6: Power Door Lock Wiring
4 PIN SENSOR PLUG/HARNESS (BLUE): White Wire: Negative Trigger Blue Wire: Negative Warn-away Black Wire: Sensor Ground Red Wire Sensor Power SHOCK SENSOR: The sensor supplied with this system does not require any additional wiring. Simply mount the sensor in a suitable location, plug it in, and adjust the sensitivity. -
Page 7: Power Door Lock Wiring
POWER DOOR LOCK WIRING NEGATIVE TRIGGER DOORLOCK WIRING GREEN BLUE REVERSE POLARITY DOOR LOCK WIRING GREEN BLUE MASTER SWITCH POSITIVE TRIGGER DOORLOCK WIRING GREEN BLUE FACTORY POWER LOCKING RELAYS AFTERMARKET MOTOR/DOOR LOCK WIRING GREEN FUSED +12V BLUE FUSED +12V FACTORY POWER LOCKING RELAYS... -
Page 8: Data Port Diagram
Data bus Systems: Data Controlled door locks, Factory Security and many accessories This unit includes DP Technology it will allow you to plug our modules which operate Data control Door locks, accessories, and Bypass Factory security systems directly into the unit by via Data Port. The module cable plugs directly to the Data port on the side of the unit. -
Page 9: Transmitter Programming
NOTE: All transmitters must be learned at the time of programming. This system can learn up to 4 remotes. 1. Turn key to the ON position and press program button 4 times. 2. After a short delay, the unit will flash the parking lights 4 times, Siren 4 times, Horn 4 times and status LED will be on solid. -
Page 10: Option Programming
1. Turn the Ignition ON and press the Override/Program button 5 times. 2. After a short delay, the parking lights will flash 5 times, Siren 5 times, Horn 5 times and status LED will be on solid. 3. Within the next few seconds, press the Override/Program button [again] the number of times that corresponds to the options chart below. - Page 11 OPTION PROGRAMMING NOTE: Options can be instantly restored to Factory Default Values. To restore default values: Perform step #1 (See page 10), then press buttons (1+2) together. The siren and horn will chirp 4 times and lights will flash 4 times. Turn OFF Ignition. All programming options will be restored to * Default * values (See page 10).
-
Page 12: Option Programming
OPTION PROGRAMMING 6. ACTIVE RE-ARMING Active Re-arming allows the system to re-arm itself 30 seconds after disarmed with the transmitter if a door has not been opened. This is handy if the vehicle is accidentally disarmed (via the Transmitter in your pocket) without you knowing it. -
Page 13: Custom Personal Override Code
14. CARJACK FEATURES This option controls the unit’s Car Jack features. Enable or Disable Carjack (Turn ON or OFF) with this option. 15. Lock/Unlock or Arm/Disarm with Ignition ON This option allows you Arm and Disarm the system with the Ignition ON. This is used when there is a remote starter added to the system. - Page 14 OPERATING INSTRUCTIONS (REMOTE OPERATIONS) ONE WAY SIDEKICK REMOTE: The transmitter supplied with the CS-2000DPII-TW2 system has four buttons. The button configuration of the CS- 2000DPII-TW2 is Factory-set and unchangeable. second vehicle operation for additional information on how to use your remote to operate a second vehicle equipped with a OnGuard system.
- Page 15 OPERATION INSTRUCTIONS (TRANSCEIVER / PAGER-REMOTE) PAGER / REMOTE TRANSCEIVER: The hand-held remote transceiver is used to send and receive information from the vehicle. The Control Module transmits High Frequency signals from the vehicle to your over long distances. Your range will vary depending on location, terrain, and local RF noise/interference.
- Page 16 OPERATION INSTRUCTIONS (LCD PANEL FUNCTIONS SHOWN) DISARM VALET DATA TRANSLATE SETTING THE CLOCK (2-WAY – LCD REMOTE) 1. Press button #5 (recall) on the side of the remote control 5 times. 2. The remote will beep and the AM or PM display will begin flashing. 3.
- Page 17 OPERATION INSTRUCTIONS ACTIVE ARMING To arm the alarm and lock the doors, press the #1 (Lock Symbol) button on the transmitter. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock and the starter will be disabled if these optional features are installed.
-
Page 18: Operating Instructions (Sidekick Remote And 2-Way Lcd Quick Guide Functions
OPERATING INSTRUCTIONS SELECTIVE SILENT ARM/DISARM THROUGH REMOTE CONTROL This system can be armed and disarmed without siren chirps on an “as needed” basis. Press and release Button #4 for arm/disarm without siren chirps. PROGRAMMABLE SILENT ARM/DISARM MODE (CHIRP DEFEAT) The system can be silently armed and disarmed as normal with Lock/Unlock Buttons, but no siren chirp. See alarm programming option (#8) to enable or disable this feature. - Page 19 OPERATING INSTRUCTIONS PRIOR INTRUSION ALERT If the system was tripped in your absence, the dash LED will be flashing rapidly. When the system is disarmed you will hear 3 chirps (and 3 light flashes). Carefully inspect your vehicle to see if there is any damage or a theft has occurred.
-
Page 20: Carjack Protection Features
CARJACK PROTECTION FEATURES ACTIVE CARJACK This feature provides Active Carjack protection and must be enabled before use through Alarm programming option (14) See page 10. When the Ignition is on (vehicle is running), press and hold button #3 (AUX) for 3 seconds. Parking lights will flash TWICE to confirm the Carjack countdown sequence. -
Page 21: Antenna Diagram
ANTENNA DIAGRAM RECOMMENDED ANTENNA LOCATIONS WINDSHIELD CS-2000DPII-TW2 Antenna System Transceiver Box & Antenna White Plug DATA PORT CS-2000DPII-TW2 ANNTENA PLUG Black Plug... -
Page 22: Wiring Diagram
Data Port Antenna Port (-) NEG. DOOR PIN SWITCH (+) POSITIVE DOOR PIN SWITCH GREEN (-) DOOR TRIGGER VIOLET (+) DOOR TRIGGER IGN. BLACK CHASSIS GROUND FUSE YELLOW (+) SWITCHED IGN "ON" OPT. GRAY (-) REMOTE OUTPUT 1 RELAY BLUE (-) HOOD/TRUNK TRIGGER (-) NEG. -
Page 23: Low Battery Warning
LOW BATTERY WARNING – LCD REMOTE LOW BATTERY WARNING The CS-2000DPII-TW2 LCD has a low battery warning system. When the battery voltage is low. The LCD pager remote will show a low voltage icon. We recommend replacing the battery for proper operation. To replace the battery, simply unlatch and slide open the battery door on the back of the remote. - Page 24 Phone (800) 998-6880 ONLINE TECHNICAL SUPPORT FAX (805) 581-9500 www.crimestopper.com © 2007 Crimestopper Security Products...