Table of Contents
Advertisement
5100
Series
Table
2-8.
Storage
Group
(Storage
Only!
(cont)
4.
ADVANCE/LOAD
Operation
of the
ADVANCE/LOAD
switch
differs
for
the
Read
Mode
and
Store
Mode.
When
the
Read
Mode
is
selected
and
the switch
is
depressed, the
next
step
in
storage
is
transferred to the
instrument
output and
the step
number
in
incre-
ments.
When
the
final
step has
been
selected,
"End P"
is
displayed
when
the
final
step
is
loaded
into
the
last
step location.
In
the
Store
Mode,
when
the switch
is
depressed the
output
state
is
transferred to
memory
at
the current step then the
step
number
is
incremented.
After entering the
final
step for
the capacity
of
memory, "End P"
is
displayed.
If
"FULL"
is
displayed, the
memory
buffer cap-
acity
would
be
exceeded and
additional
commands
cannot
be accepted.
5.
SEL/DISPLAY STEP
Operation
of the
SEL/DISPLAY STEP
switch
is
controlled
by
the operation
pre-
ceding depression of the
switch,
if
the
operation
is
not preceded
by
the entry of
a
numerical
value, the
step
number
of the
selected step
is
flashed
on
the
Central
Display.
If
preceded
by
a
numerical
entry,
the action taken
is
dependent upon
whether
the
Read
or
Store
Mode
is
selected,
if
there
is
a
program
entered
and
whether
or
not
the step
selected
is
within
an
existing
program.
When
the
Read
Mode
is
selected,
the step
number
flashes,
then the
stored
output
state
is
trans-
ferred to the
instrument
output..
If
the
number
selected
is
greater
than the
last
step
in
the
program,
"End
P"
is
displayed,
in
the Store
Mode,
the
number
selected
is
displayed,
and
that
becomes
the step
referenced
in
storage operations.
If
the
sel-
ected
number
is
greater
than
the
last
step
in
the
program
the
number
of the
first
unused
step
is
displayed
and
the
final
step
is
referenced.
In
the Store
Mode
the
Output
does not change
when
selecting or
displaying
steps.
6.
DELETE
STEP
The
step selected
for
operation
is
deleted
when
the
DELETE STEP
switch
is
depressed
when
the Store
Mode
is
selected.
The
step
numbers
of
any
subsequent
steps are
automatically
decremented
so there
are
no
gaps
in
the sequence.
The
data
replacing the deleted instruction
is
displayed.
"Err
1"
is
displayed
if
the
DELETE
STEP
switch
is
depressed with the
Read
Mode
selected.
7.
LIST
Used
with
one
of the Optional Interfaces to print
an
80
column
listing
of
either
all
or part of the stored
program
(Store
Mode)
or the
results
of
an
individual
test
(Read Mode).
8.
CLEAR
STORAGE
In
the Store
Mode
all
data
in
the storage
memory
is
deleted
and
"End P"
is
displayed
when
the
CLEAR STORAGE
switch
is
depressed.
If
the
switch
is
depressed
in
the
'Read
Mode
"Err 1"
is
displayed
and no
clearing action
results.
9.
Tape System
Tape
Unit
to
Read/Store
data using
a
mini-cassette
system, providing
a
permanent
record of
test
programs.
2-11
Advertisement
Table of Contents
