Panasonic AW-HE38HWP Operating Instructions Manual page 78

Web screen configurations
Detail
The image detail (image sharpness) is adjusted here.
When "Low" or "High" is selected, the detail is enhanced.
Setting value: Off, Low, High
Factory settings: Low
Detail Level H
The image sharpness level is adjusted here when "High"
has been selected as the "Detail" setting.
Setting range: Detail Level L setting +1 to 18
Factory settings: 18
Detail Level L
The image sharpness level is adjusted here when "Low"
has been selected as the "Detail" setting.
Setting range: 1 to Detail Level H setting –1
Factory settings: 9
Flesh Tone Mode
Set here is the flesh tone mode for displaying the subjects'
skin so that it appears more smoothly and eye-pleasingly.
When "Low" or "High" is selected, the effect is enhanced.
Setting value: Off, Low, High
Factory settings: Off
HDR
Adjust the effect of the high dynamic range mode.
When HDR is set to "Low", correction is performed so
that the appropriate exposure is obtained for the light and
dark areas on subjects with extremely high contrast. When
"High" is selected, dark areas are made brighter.
Depending on the shooting conditions, however, the
picture quality may drop with increased noise.
In addition, unit vibration may result in blurry or distorted
images.
This effect is not recommended in shooting locations
where significant vibration may occur.
Setting value: Off, Low, High
Factory settings: Off
Notes
● When the HDR setting is changed, the monitor
images will go momentarily black and the audio will
be muted. Furthermore, IP video may stop for about
30 seconds.
● When "Low" or "High" is selected, it will take longer
for the brightness of the image to converge.
● When "Low" or "High" is selected, brightness cannot
be adjusted.
● When "Low" or "High" is selected, video will be
delayed by 4 frames.
● When "Low" or "High" is selected, the following
settings cannot be changed.
• Day/Night
• Night-Day Level
• Pedestal
• DRS
• Gamma Type
• Back Light COMP.
• Freeze During Preset
• Image Stabilizer
78
(continued)
Notes
● When "Low" or "High" is selected, the OSD menu
cannot be displayed for the video on the Web
screen. However, the OSD menu can be displayed
over video output to a monitor.
● If you attempt to display the OSD menu on the Web
screen when "Low" or "High" is set, the HDR item
becomes bar display and the setting cannot be
changed. Change the setting from the Web setting
screen, infrared remote control, etc.
● When the priority mode (page 44, page 65) is
"IP" mode and when HDR is set to "Low" or "High",
there are the following restrictions.
• JPEG(1) to (3): Fixed to 640×360.
• H.264(1): 1280×720 cannot be used.
• H.264(2) to (4): Cannot be used.
● When the Priority Mode (page 44, page 65)
selection is "NDI|HX", this item is fixed to "Off".
DNR
Set here is the level of the digital noise reduction effect so
that light, noise-free and clear images will be output even
at night and in other low-brightness environments.
When "Low" or "High" is selected, noise can be eliminated.
However, there is an increased possibility that afterimages
may occur.
Setting value: Off, Low, High
Factory settings: Low
Pedestal
This item is used to adjust the black level (adjust the
pedestal) so that the dark parts of the images are easier
to see.
These parts become darker when a negative setting is
selected and, conversely, lighter when a positive setting is
selected.
Setting range: –10 to +10
Factory settings: 0
DRS
Set here is the DRS function which provides just the right
amount of compensation when images with significant
light/dark differences are displayed.
When "Low" or "High" is selected, the effect is enhanced
even more.
Depending on the shooting conditions, however, the
picture quality may drop with increased noise.
Setting value: Off, Low, High
Factory settings: Off