Operation; Warranty - Napa CARLYNE TOOLS 6-1151 Manual

OPERATION

Select a suitable abrasive disc and
make sure that it is fixed securely to the
pad. Connect a suitable air supply as
recommended in Figure 1. The air inlet on
this tool has a standard ¼" NPT thread
After mounting sandpaper, start this
Sander under a bench in order to make
sure sandpaper is firmly attached. Set the
sander down on the work evenly and move
it slowly back & forth in wide, overlapping
areas. Additional pressure may be used to
make more efficient use of the tool when
material to be sanded is thick. Lighter
pressure may be used in delicate sanding
or when using edges of sanding pad.
When finished sanding, lift it off the work
before stopping the motor.
Take great care when sanding around
sharp edges and surfaces to avoid disc
snagging, i.e. the disc may be brought to an
abrupt stop or considerably slowed which
will cause the tool to kick in the operator's
hands. It is always recommended to use
safety gloves and safety glasses. The
sanding of certain materials may create a
hazardous dust which may require special
breathing equipment. Check before using
the tool. It is recommended to use proper
breathing equipment while sanding. Even
if the tool has a low noise level, the actual
sanding process may cause a noise level
such that ear protection should be used.
It is recommended that ear protection be
used while sanding.

WARRANTY

Important: DO NOT RETURN DEFECTIVE PRODUCT OUTSIDE OF ORIGINAL ONE (1) YEAR WARRANTY PERIOD TO
PLACE OF PURCHASE.
WARRANTY POLICY:
This Carlyle Air Tool is warranted against defects in material and workmanship for a period of One (1) Year from the date of origi-
nal purchase. We will replace, at our option, any part which proves to be defective in material or workmanship. Repairs or replacements are warranted as
described above for the duration of the original warranty period. In the unlikely event a replacement unit is required during this One (1) year period, return
the unit to your local NAPA Auto Parts Store for a replacement. This warranty does not apply to products which have been subjected to abuse, misuse, modi-
fication, neglect, lack of maintenance, use in a production-related service, or repaired by anyone other than an Authorized Carlyle Air Tool Service Center.
For complete listing of Authorized Master Repair Centers, see enclosed Customer Warranty Repair Form, or
visit www.toolwarrantyrepair.com
6-1151, 6-1153, 6-1153
Do not continue to use abrasive discs that
are worn or clogged. This will make the
sanding process inefficient and increases
the need to apply unnecessarily high
forces to the tool. Do not use oversized or
undersized sanding discs. The disc should
be no more than ¼" larger in diameter
than the pad and never be smaller than
the pad size.
An air regulator is located on the side of
the tool housing. It can be used to vary the
volume of compressed air fed to the motor
which will vary the speed of the sander.
NOTE: During operation, safety
goggles should always be worn to
guard against flying debris (users &
bystanders)." (BOLD)
6-1151 - Specifications
Horsepower . . . . . . . . . . . . . . . . . . . . 0.3HP
Overall Length . . . . . . . . . . . . . . . . . . 7.33"
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . .9"
Weight . . . . . . . . . . . . . . . . . . . . . . .2.7 lbs.
RPM . . . . . . . . . . . . . . . . . . . . . . . . . 12,000
Vacuum Type . . . . . . . . . . . . . .Non vacuum
Sound Level . . . . . . . . . . . . . . . . . 81.2 dBa
Air Consumption . . . . . . . . . . . . . . . 2.4 CFM
Air Inlet Thread Size . . . . . . . . . . . 1/4" NPT
Recommended
Hose Size . . . . . . . . . . . . . . . . . . . . 3/8" I.D.
Recommended
Air Pressure . . . . . . . . . . . . . 90psi (6.2 bar)
Throttle
6
6-1152 - Specifications
Horsepower . . . . . . . . . . . . . . . . . . . . 0.3HP
Overall Length . . . . . . . . . . . . . . . . . . . 7.3"
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . .9"
Weight . . . . . . . . . . . . . . . . . . . . . . .2.7 lbs.
RPM . . . . . . . . . . . . . . . . . . . . . . . . . 12,000
Vacuum Type . . . . . . . . . . . . . .Non vacuum
Sound Level . . . . . . . . . . . . . . . . . 81.2 dBa
Air Consumption . . . . . . . . . . . . . . . 2.4 CFM
Air Inlet Thread Size . . . . . . . . . . . 1/4" NPT
Recommended
Hose Size . . . . . . . . . . . . . . . . . . . . 3/8" I.D.
Recommended
Air Pressure . . . . . . . . . . . . . 90psi (6.2 bar)
6-1153 - Specifications
Horsepower . . . . . . . . . . . . . . . . . . . . 0.3HP
Overall Length . . . . . . . . . . . . . . . . . . . 9.6"
Width . . . . . . . . . . . . . . . . . . . . . . . . . . 6.2"
Weight . . . . . . . . . . . . . . . . . . . . . . .1.6 lbs.
RPM . . . . . . . . . . . . . . . . . . . . . . . . . 12,000
Vacuum Type . . . . . . . . . . . . . .Non vacuum
Sound Level . . . . . . . . . . . . . . . . . 81.2 dBa
Air Consumption . . . . . . . . . . . . . . . 2.4 CFM
Air Inlet Thread Size . . . . . . . . . . . 1/4" NPT
Recommended
Hose Size . . . . . . . . . . . . . . . . . . . . 3/8" I.D.
Recommended
Air Pressure . . . . . . . . . . . . . 90psi (6.2 bar)
Throttle
Air Inlet
Speed
Regulator
Air Inlet
Speed
Regulator
Rev. 05/22/23