Others; Troubleshooting - Panasonic SC-TMAX45 Operating Instructions Manual

M-1 to M-9 Selection of 9 illumination patterns in
multiple colours.
S-1 to S-3 Selection of 3 illumination patterns in single
colour.
Press [ILLUMINATION] repeatedly to select
a colour.
OFF Switch off illumination and strobe lights, also
decrease the brightness of the display panel.
Using strobe lights
Press and hold [ILLUMINATION] to switch on or
switch off the strobe lights.

Others

Auto off
This function will automatically switch the system to
standby mode if there is no sound and it is not being used
for approximately 20 minutes.
Note:
This function may not work when a microphone/guitar is
connected.
Software update
Occasionally, Panasonic may release updated software
for this unit that may add or improve the way a feature
operates. These updates are available free of charge. For
more details, refer to the following website.
https://panasonic.jp/support/global/cs/audio/
(This site is in English only.)

Troubleshooting

Before requesting service, make the following checks. If
you are in doubt about some of the check points, or if the
solutions indicated do not solve the problem, consult your
dealer for instructions.
█ Common problems
The unit does not work.
•
The safety device has been activated. Do the following:
1.
Press [1] on the main unit to switch the unit to standby
mode. If the unit does not switch to standby mode,
disconnect the AC mains lead and then connect it again.
2.
Press [1] again to switch on the unit. If the problem
persists, consult your dealer.
Sound is distorted or no sound.
•
Adjust the volume of the system.
•
Switch off the system, determine and correct the cause, and
then switch on again. It can be caused by straining of the
speakers through excessive volume or power, and when
using the system in a hot environment.
A humming sound can be heard during playback.
•
An AC mains lead or fluorescent light is near the cables.
Keep other appliances and cords away from the cables of
this system.
The sound level reduces.
•
The protection circuit has been activated due to the
continuous use at high volume output. This is to protect the
system and maintain the sound quality.
█ USB
The USB device or the contents in it cannot be read.
• The format of the USB device or the contents in it are not
compatible with the system.
• USB devices with storage capacity of more than 32 GB
cannot work.
•
USB devices may not be recognised when connected to this
system with a USB extension cable or USB hub.
Slow operation of the USB device.
• Large content size or large memory USB device takes
longer time to read.
█ Bluetooth
®
Pairing cannot be done.
• Check the Bluetooth device condition.
®
•
The device is out of the 10 m communication range. Move
the device nearer to the system.
The device cannot be connected.
• The pairing of the device was unsuccessful. Do pairing
again. (~6)
•
The pairing of the device has been replaced. Do pairing
again. (~6)
•
This system might be connected to a different device.
Disconnect the other device and try connecting the device
again.
•
The system may have a problem. Switch off the system and
then switch on again.
The device is connected but audio cannot be heard
through the system.
•
For some built-in Bluetooth
audio output to "SC-TMAX45" or "SC-TMAX15" manually.
Read the operating instructions of the device for details.
Playback during Multi Connect is not working or no sound.
• Restart the app of the device.
•
The control of the device was not switched successfully.
Disconnect the existing connected devices and try again.
Sound from the device is interrupted.
• The device is out of the 10 m communication range. Move
the device nearer to the system.
•
Remove any obstacle between the system and the device.
•
Other devices that use the 2.4 GHz frequency band
(wireless router, microwaves, cordless phones, etc.) are
interfering. Move the device nearer to the system and
distance it from the other devices.
Factory reset
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1
Turn [VOLUME] to set the volume to "0".
2
Press and hold [INPUT SELECTOR] and [BASS].
Continue to press and hold the buttons until
"RESET" is shown.
All the settings are set back to the factory preset.
Note:
You cannot perform factory reset when Bluetooth
function is switched on.
® devices, you have to set the
standby
®
9
9