Table of Contents
Advertisement
English
DESCRIPTION (Fig. A)
WARNING :
Never modify the power appliance or
any part of it. Damage or personal injury could result.
Top handle/cord wrap
1
Power cord
2
On/off switch
3
Vacuum head
4
Lid latches
5
Dust tank
6
Hose
7
Casters
8
Clean connect
9
TM
Vacuum port
10
Hose strap
11
12
Disposable dust bag
ASSEMBLY AND ADJUSTMENTS (Fig. A–C)
WARNING: To reduce the risk of injury, turn
appliance off and disconnect appliance from
power source before installing and removing
accessories, before adjusting or changing
set-ups or when making repairs.
start-up can cause
injury.
WARNING:
place while vacuuming, except as described
under
WET PICK UP APPLICATIONS
OPERATION
may also need to use an disposable dust bag to
make emptying the dust tank easier.
1. Install the disposable dust bag
in
Fig.
B.
NOTE: Be careful not to tear the bag. Place bag
securely onto vacuum port
seal for maximum dust collection performance.
2. Place the vacuum head
secure it by closing the lid latches
3. Insert the end of hose
port
and tighten the end of hose to the tank.
10
OPERATION
INSTRUCTIONS FOR USE (Fig. A, D, E)
WARNING:
Always observe the safety instructions
and applicable regulations.
1. Plug the power cord into an appropriate outlet.
2. Turn the on/off switch
3
3. The D
E
with the D
WALT connection system. It allows a
E
fast, secure connection between the hose
and power tool. The connector
directly to D
WALT compatible tools or through the
E
use of an adapter (available from local D
supplier). If you need Install the adapters, refer to
Fig.
E.
NOTE:
attached to the tool outlet before following the steps
below.
An accidental
must always be in
9
under
, as shown
12
to provide a tight
10
onto the dust tank and
4
.
5
7
into clip-in hose vacuum
to the ON position ( I ).
7
connects
13
WALT
E
OPERATING INSTRUCTIONS
CASTER INSTALLATION (Fig. A, F)
1. Invert the dust tank and install the casters to the
2. Return dust tank assembly upright.
REMOVE/CHANGE USED DISPOSABLE
DUST BAG (Fig. A)
WARNING:
Appropriate personal protective
equipment like dust mask and gloves should be used
while handling used dust bags.
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch lid latches
5
3. Pull the disposable dust bag
port
.
10
4. Seal the disposable dust bag
removing it from the machine.
5. Dispose the disposable dust bag
container according to statutory provisions.
WET PICK UP APPLICATIONS (Fig. A, G)
WARNING:
If foam or liquid escapes from the
machine,switch off immediately.
WARNING:
Do not use the machine with this set
up for dust Class L.
14
the dust tank is full and the sound of the motor will
change at once.
When the motor has a high pitched sound and air/
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch lid latches
5
head
4
.
3. Empty contents of dust tank
or drain.
CAUTION:
Clean the water level limiting device
regularly and examine it for signs of damage. Refer to
Fig.
G.
NOTICE:
water from entering the motor.
Before using the vacuum for wet pick up:
• Ensure the dust tank is empty and free of excessive dust.
9
TO CONVERT BACK TO DRY VACUUM
OPERATION (Fig. A)
1. Empty dust tank, refer to
instructions.
2. Place dust tank upside down position until dry. DO
NOT use wet dust tank for dry pick up.
3. Place vacuum head
INSTALL FILTERS.
5. When dust tank is dry place the vacuum head
onto the dust tank and secure it by closing the
lid latches
.
5
7
and remove vacuum head
carefully from vacuum
12
opening tightly when
12
in appropriate
12
and remove vacuum
into a suitable container
6
14
TO EMPTY DUST TANK
on a level surface appliance dry.
4
4
.
TO
4
Advertisement
Table of Contents
