1. Manuals
  2. Brands
  3. Titan Tool Manuals
  4. Paint Sprayer
  5. SPEEFLO PowrTwin 6900 DI Plus
  6. Owner's manual

Titan Tool SPEEFLO PowrTwin 6900 DI Plus Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PowrTwin 6900 DI Plus
Model Numbers:
Gas Complete
Electric Complete
Printed in the U.S.A.
SPEEFLO
0290021
0290029
Owner's Manual
For professional use only
Do not use this equipment
before reading this manual!
NOTE: This manual contains important
warnings and instructions. Please
read and retain for reference.
© Titan Tool Inc. All Rights Reserved. Form No. 0290911D
1011
•

Advertisement

Table of Contents
loading

Related Manuals for Titan Tool SPEEFLO PowrTwin 6900 DI Plus

Summary of Contents for Titan Tool SPEEFLO PowrTwin 6900 DI Plus

  • Page 1 PowrTwin 6900 DI Plus Model Numbers: Gas Complete 0290021 NOTE: This manual contains important Electric Complete 0290029 warnings and instructions. Please read and retain for reference. © Titan Tool Inc. All Rights Reserved. Form No. 0290911D 1011 • Printed in the U.S.A.

  • Page 2: Safety Precautions

    (add more hose if necessary). Flammable vapors are often heavier than air. Floor area must be extremely well ventilated. The pump contains arcing parts that emit sparks and can ignite vapors. © Titan Tool Inc. All rights reserved.

  • Page 3: Grounding Instructions

    If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician. Grounded Outlet IMPORTaNT: Do not lift by cart handle when loading or unloading. Grounding Pin Cover for grounded outlet box © Titan Tool Inc. All rights reserved.

  • Page 4: Table Of Contents

    26” W (66 cm) x 35” H (89 cm) Fluid section wetted parts: Electroless nickel plated ductile iron, electroless nickel plated carbon steel, stainless steel, tungsten carbide, Teflon, thiokol impregnated leather, ultra high molecular weight polyethylene. © Titan Tool Inc. All rights reserved.

  • Page 5: Introduction

    86 or higher, or that has a research octane number of 91 or higher. Use of a lower octane gasoline can cause persistent “pinging” or heavy “spark knock” (a metallic rapping noise) which, if severe, can lead to engine damage. © Titan Tool Inc. All rights reserved.

  • Page 6: Operating The Swing Cart

    Use a short electric cable and a long paint hose. Any extension cord will create some voltage drop. If an extension cord is necessary, use only a grounded 3-wire #12 gauge extension cord. © Titan Tool Inc. All rights reserved.
  • Page 7 OFF position. To turn off the electric motor, • set the pressure to minimum by turning the pressure control knob fully counterclockwise, • move the ON/OFF switch to the OFF position. © Titan Tool Inc. All rights reserved.

  • Page 8: Preparing To Paint

    13. Unlock the gun by turning the gun trigger lock to the Lever to the ON position, unlocked position. • pull the starter rope briskly until the engine starts. To start the electric motor, move the ON/OFF switch to the ON position. © Titan Tool Inc. All rights reserved.

  • Page 9: Pressure Relief Procedure

    3. Place the siphon tube into a container of the appropriate solvent. IMPORTaNT: use only compatible solvents when cleaning out oil based enamels, lacquers, coal tar, and epoxies. check with the fluid manufacturer for the recommended solvent. © Titan Tool Inc. All rights reserved.

  • Page 10: Cleaning A Clogged Tip

    1. Remove the retaining ring from the Foot Valve foot valve housing Housing 2. Remove the inlet screen from the Foot valve housing. Inlet Screen 3. Clean thoroughly with the appropriate solvent. Retaining Ring © Titan Tool Inc. All rights reserved.

  • Page 11: Maintaining The Filter Assembly

    5. Place the thin Teflon gasket onto the step at the top of the filter body. 6. Place the thick Teflon gasket onto the top of the thin gasket. 7. Tighten the filter cap assembly onto the filter body. © Titan Tool Inc. All rights reserved.

  • Page 12: Basic Engine Maintenance (Gas Engine)

    NOTE: Brushes should be replaced when they are worn to less than 1/2 inch. check and replace both also the RESET! brushes at the same time. 1. Remove both inspection covers on the motor. © Titan Tool Inc. All rights reserved.

  • Page 13: Troubleshooting

    Hose size or length is too small or too long Increase hose size to minimize pressure drop through hose and/or reduce hose length. Solvent has caused upper packing to swell Replace packing. Pump chatters on up or down stroke © Titan Tool Inc. All rights reserved.

  • Page 14: Hydraulic Motor

    NOTE: Engine labors at stall on if the head becomes hotter. This will help determine both strokes. if center o-ring is blown on spool valve. If hot, remove and replace o-ring. Bad hydraulic pump Replace hydraulic pump. © Titan Tool Inc. All rights reserved.

  • Page 15: Spray Patterns

    Remove restrictions in system; clean tip screen if filter is used. Round pattern Worn tip Replace tip. Fluid too heavy for tip Increase pressure. Thin material. Change nozzle tip. © Titan Tool Inc. All rights reserved.
  • Page 16 3600 PSI. Ceci est valable de chiffons et autres matières inflammables. Français © Titan Tool Inc. Tous droits réservés.
  • Page 17 13. Ne pulvérisez pas à l’extérieur par temps venteux. 14. Débranchez toujours le cordon électrique de la prise avant de travailler sur l’équipement. IMPORTaNT: Ne pas soulever par la poignée du chariot lors du chargement ou du déchargement. © Titan Tool Inc. Tous droits réservés. Français...
  • Page 18 11. Antes de utilizar el aparato, verifique que todas las que pulverice. Lea las hojas de datos sobre seguridad conexiones son seguras. de los materiales (MSDS) y las etiquetas en los botes de Español © Titan Tool Inc. Todos los derechos reservados.
  • Page 19 13. No pulverice al aire libre si hace viento. 14. Desenchufe siempre el cable antes de trabajar en el equipo. IMPORTaNTE: No cargue el equipo por el asa del carrito durante la carga y descarga. © Titan Tool Inc. Todos los derechos reservados. Español...

  • Page 20: Parts Lists And Service Instructions

    Belt, “V” (gas model, not shown) 0290528 Hydraulic cover 506-279 Convertokit, DC electric, 120V (electric 770-879 Lock washer model, includes belt, not shown) 862-501 Screw 506-251 Convertokit, 3 HP, electric, 230V (electric model, not shown) ---------- Hydraulic system © Titan Tool Inc. All rights reserved.

  • Page 21: Cart Assembly

    Belt Guard assembly (P/N 0290518) Item Part No. Description Qty. 9805329 Screw 0290523 Cover 0290521 Belt guard, rear 9802252 Screw 0290524 Bracket 9805255 Screw 9802526 Screw 0290794 Hinge 0524318 0290522 Guard, front 0290820 Label (not shown) © Titan Tool Inc. All rights reserved.

  • Page 22: Hydraulic Motor

    © Titan Tool Inc. All rights reserved.
  • Page 23 Install the spool through the top of the cylinder head, down into the sleeve. IMPORTaNT: Do not use Piston Lube pump packing lubricant. It is a solvent and will severely damage seals and O-Rings of the hydraulic motor. © Titan Tool Inc. All rights reserved.

  • Page 24: Fluid Section

    3, 4, 10, 12, 16, 19, 21, and Loctite P/N 426-051) 451-085 Outlet valve cage 451-133 Foot valve assembly (includes items 18–24) 138-225 Outlet valve ball 236-050 Outlet valve assembly (includes items 9–13) 236-012 Outlet valve seat © Titan Tool Inc. All rights reserved.
  • Page 25 Insert the outlet valve cage (9), new outlet valve ball (10), new or flipped seat (worn side away from ball), and a new seal washer (12) into the displacement rod (6). © Titan Tool Inc. All rights reserved.

  • Page 26: Hydraulic System

    Use blue Loctite on threads, Torque to 8 FT/LBS (11 N/m) 449-135 Spacer Torque to 8 FT/LBS (11 N/m) 451-121 Elbow (not shown) 24, 29-30 Torque to 15 FT/LBS (20,5 N/m) 941-555 Ball valve (not shown) Torque to 20 FT/LBS (28 N/m) © Titan Tool Inc. All rights reserved.

  • Page 27: Gas Convertokit

    Belt, “V” (not shown, not part of assembly) 977-228 Pulley 590-068 Handle grip 335-017 Handle 860-552 Screw 459-018 Mount plate 506-255 Rectifier (not shown) 506-258 Fan (not shown) 449-181 Belt, “V” (not shown, not part of assembly) © Titan Tool Inc. All rights reserved.

  • Page 28: Electric Convertokit, 230V

    Screw, HH 944-038 Stem o-ring 590-068 Handle grip 944-031 Valve housing 335-016 Handle 944-039 Ball 944-043 Valve seat 449-181 Belt, “V” (not shown, not part of assembly) 944-044 Valve seal 944-013 Valve seat retainer © Titan Tool Inc. All rights reserved.

  • Page 29: Filter Assembly

    Valve seat (1) 3/8” NPT(F) plugged for 138-226 Ball, T.C. additional gun hookup 945-026 Valve stem stop Wetted Parts ........Carbon steel with electroless nickel plating, stainless steel, 891-183 O-ring, Teflon tungsten carbide, Teflon © Titan Tool Inc. All rights reserved.

  • Page 30: Gun Manifold Assemblies (Optional)

    3 Gun 4 Gun 2 Gun 3 Gun 4 Gun 1/4” 1/4” 1/4” 3/8” 3/8” 3/8” 975-111 1 Gun Add-On, 1/4” 975-311 1 Gun Add-On, 3/8” 975-200 Add-A-Gun Kit, 1/4” 975-300 Add-A-Gun Kit, 3/8” © Titan Tool Inc. All rights reserved.

  • Page 31: Sae O-Ring Fitting Installation

    5 mesh filter Fan widths measuring 8” to 12” (20 to 30 cm) are most preferred because they offer more control while spraying and are less likely O-ring cut on to plug. thread © Titan Tool Inc. All rights reserved.

  • Page 32: Warranty

    Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. With the exception of any special, limited, or extended warranty published by Titan, Titan’s obligation under this warranty is limited to replacing or repairing without charge those parts which, to Titan’s...

Table of Contents