Titan Tool 1140ix Owner's Manual
  1. Manuals
  2. Brands
  3. Titan Tool Manuals
  4. Paint Sprayer
  5. 1140ix
  6. Owner's manual

Titan Tool 1140ix Owner's Manual

Airless sprayer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Do not use this equipment before reading this manual!
Model Number:
High Rider Bare
High Rider Complete
Low Rider Bare
Low Rider Complete
Printed in the U. S. A.
1140
Airless Sprayer
800-3000
800-3005
800-3010
800-3015
Owner's Manual
For professional use only
ix
NOTE: This manual contains important warnings
NOTE: This manual contains important warnings
and instructions. Please read and retain for
and instructions. Please read and retain for
reference.
reference.
0104 © 2004 Titan Tool Inc. All rights reserved. Form No. 313-2385, REV A

Advertisement

Table of Contents
loading

Related Manuals for Titan Tool 1140ix

Summary of Contents for Titan Tool 1140ix

  • Page 1 Please read and retain for and instructions. Please read and retain for Low Rider Bare 800-3010 reference. reference. Low Rider Complete 800-3015 0104 © 2004 Titan Tool Inc. All rights reserved. Form No. 313-2385, REV A Printed in the U. S. A.

  • Page 2: Table Of Contents

    Do not use plastic drop cloths when PSI/228BAR fluid pressure. spraying flammable materials. PREVENTION: • Use lowest possible pressure to flush equipment. • NEVER aim the gun at any part of the body. © Titan Tool Inc. All rights reserved.
  • Page 3 W- A after the cord type designation. For example, a designation of SJTW-A would indicate that the cord would be appropriate for outdoor use. © Titan Tool Inc. All rights reserved.

  • Page 4: General Description

    6. Turn the unit off by moving the pressure control knob to least 25’ from the spray area. the OFF position in the black zone. NOTE: Make sure that the spray gun does not have a tip or tip guard installed. © Titan Tool Inc. All rights reserved.

  • Page 5: Painting

    11. Trigger the gun into the metal waste container until all air and solvent is flushed from the spray hose and paint is flowing freely from the gun. © Titan Tool Inc. All rights reserved.

  • Page 6: Pressure Relief Procedure

    Never trigger the gun unless the tip is in either the spray or the unclog position. Always engage the gun trigger lock before removing, replacing, or cleaning tip. pass pass pass pass pass © Titan Tool Inc. All rights reserved.

  • Page 7: Practice

    2. Remove the gun tip and tip guard and clean with a brush Never pull on a wire to disconnect it. Pulling on a wire using the appropriate solvent. could loosen the connector from the wire. © Titan Tool Inc. All rights reserved.

  • Page 8: Replacing The Prime/Spray Valve

    Cam Base Filter Valve Stem Valve Groove Pin Handle Handle NOTE: For more detail, part number information, and assembly drawings at larger scale, please see the LX -80 Professional Airless Gun Owner's Manual (#313-012). © Titan Tool Inc. All rights reserved.

  • Page 9: Replacing The Motor Assembly

    Front End Bell Assembly Gearbox Motor Mounting Housing Armature Gear Screw 1st Stage Gear Electronic Control Assembly 2nd Stage Gear Motor Baffle Assembly Front Gear Box Assembly Housing Housing Gasket Gasket Shroud Gasket Shroud Gasket © Titan Tool Inc. All rights reserved.

  • Page 10: Replacing The Transducer

    Retainer 6. Remove, clean, and inspect the Lower outlet valve cage and outlet Housing valve ball. Replace if they are worn or damaged. 7. Reassemble the valves by reversing the steps above. © Titan Tool Inc. All rights reserved.
  • Page 11 15. Thread the upper seal retainer Raised Lip NOTE: Repacking kit P/N 800-273 is available. For into the upper housing and best results use all parts supplied in this kit. torque to 25-30 ft. lbs. © Titan Tool Inc. All rights reserved.

  • Page 12: Français

    2. Needle assembly out of adjustment 2. Adjust 3. Dirty gun 3. Clean Gun does not spray 1. No paint 1. Check fluid supply 2. Plugged filter or tip 2. Clean 3. Broken needle in gun 3. Replace © Titan Tool Inc. All rights reserved.
  • Page 13 2. Use a minimum of 50' (15m) of 1/4" high pressure hose 3. Tip too large or worn 3. Replace with a new or smaller tip Patents These products are covered by one or more of the following U.S. patents: 4,500,119 4,768,929 © Titan Tool Inc. All rights reserved.

  • Page 14: Español

    • Tous les accessoires doivent être homologués pour une pression égale ou supérieure à 3 200 lb/po2 / 228BAR. Cela s'applique, entre autres, aux têtes de pulvérisation, aux accessoires du pistolet et aux flexibles. © Titan Tool Inc. Tous droits réservés. Français...
  • Page 15 égale ou supérieure à 3 200 lb/po2 / 228BAR. • Ne jamais pulvériser lorsqu'il vente. • Porter des vêtements pour protéger la peau et les cheveux contre tout contact avec la peinture. © Titan Tool Inc. Tous droits réservés. Français...
  • Page 16 • Todos los accesorios deben tener una capacidad de 3300 para obtener información completa de seguridad. lb/pulg2 / 228BAR o mayor. Esto incluye las boquillas de atomizador, pistolas, extensiones y mangueras. © Titan Tool Inc. Todos los derechos reservados. Español...
  • Page 17 W-A después de la designación del tipo de cable. Por ejemplo, SJTW-A para indicar que el cable es apropiado para uso en exteriores. © Titan Tool Inc. Todos los derechos reservados. Español...

  • Page 18: Parts Listings

    PRIME/SPRAY valve assembly....1 858-625 Screw............2 800-269 Fitting ............1 800-328 Knock-off nut..........1 800-267 Fitting ............1 800-300 Fluid section assembly .......1 860-002 Lock washer..........2 451-241 Siphon tube..........1 860-535 Screw............2 730-334 Hose clamp..........1 800-266 Hose (not shown) ........1 © Titan Tool Inc. All rights reserved.

  • Page 19: Drive Assembly

    Circuit breaker ..........1 800-366 Wire cover, 7” (not shown) ......1 800-075 Mounting plate ..........1 800-368 Wire assembly (not shown) ......1 NOTE: All electrical work should be performed by a Titan authorized service center. © Titan Tool Inc. All rights reserved.

  • Page 20: Fluid Section Assembly

    NOTE: When repacking the fluid section, make sure the raised lip on the bottom of the lower packing is fully outside the packing around the piston rod after insertion of the piston rod. © Titan Tool Inc. All rights reserved.

  • Page 21: High Rider Cart

    800-915 PRIME/SPRAY valve assembly....1 800-279 Cart (includes items 7 and 9) .....1 800-907 Plug, 1/4” ............1 335-018 Plug.............2 800-437 Transducer..........1 856-002 Washer............4 856-921 Screw............4 800-007 Axle.............1 670-109 Wheel............2 870-004 Washer............2 800-019 Cap .............2 © Titan Tool Inc. All rights reserved.

  • Page 22: Siphon Set Assembly (Low Rider)

    Handle assembly 800-109 Wheel spacer..........2 (includes items 1–3 and 5–7) .....1 800-593 Wheel............2 590-508 Roll pin............2 800-111 Cap .............2 856-921 Screw............4 800-112 Cart weldment (includes items 8 and 10)...1 856-002 Washer............4 700-674 Plug.............2 © Titan Tool Inc. All rights reserved.

  • Page 23: Prime/Spray Assembly

    Potentiometer Assy BLACK ORANGE 800-277 Electronic Control Assy GREEN Motor BLACK WHITE Relay 800-276 WHITE Indicator Lights Assembly 800-278 BLACK/RED/WHITE NOTE: All electrical work should be performed by a Titan authorized service center. © Titan Tool Inc. All rights reserved.

  • Page 24: Warranty

    Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. With the exception of any special, limited, or extended warranty published by Titan, Titan’s obligation under this warranty is limited to replacing or repairing without charge those parts which, to Titan’s reasonable satisfaction, are shown to be defective within...

This manual is also suitable for:

800-3000800-3005800-3010800-3015

Table of Contents