Special Safety Instructions - Metabo KH 5-40 Original Instructions Manual

en ENGLISH
dust collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent
use of tools allow you to become complacent
and ignore tool safety principles. A careless
action can cause severe injury within a fraction of a
second.
3.4 Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the rate
for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any
adjustments, changing accessories, or storing
power tools. Such preventive safety measures
reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools and accessories.
Check for misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the power tool's
operation. If damaged, have the power tool
repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for safe
handling and control of the tool in unexpected
situations.
3.5 Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.

4. Special Safety Instructions

4.1 Safety instructions for all operations
a) Wear ear protectors. Exposure to noise can
cause hearing loss.
b) Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
c) Hold the power tool by insulated gripping
surfaces, when performing an operation where
10
the cutting accessory or fasteners may contact
hidden wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the
operator an electric shock.
4.2 Safety instructions when using long drill
bits with rotary hammers
a) Always start drilling at low speed and with
the bit tip in contact with the workpiece. At
higher speeds, the bit is likely to bend if allowed to
rotate freely without contacting the workpiece,
resulting in personal injury.
b) Apply pressure only in direct line with the bit
and do not apply excessive pressure. Bits can
bend, causing breakage or loss of control, resulting
in personal injury.
4.3 Further Safety instructions
Pull the plug out of the socket before making any
adjustments, changing tools, maintaining or
cleaning.
Always work with the additional handle correctly
installed.
Always hold the machine with both hands on the
intended handles, take a secure stance and
concentrate on the work.
Wear personal protective equipment and
always wear safety glasses. Protective
equipment such as dust mask, non-skid safety
shoes, protective gloves, hard hat, or hearing
protection used for appropriate conditions will
reduce personal injuries.
Ensure that the place where you wish to work is free
of power cables, gas lines or water pipes (e.g.
check using a metal detector).
Work only with a correctly fitted tool. Pull on the tool
to check that it is correctly seated. (It must be
possible to move the tool a few centimetres in an
axial direction.)
When working above ground level, ensure that the
area below you is clear.
Never touch the tool or parts near the tool directly
after work because they may be extremely hot and
can cause burns to the skin,
Always position the power cable so that it leads
away from the back of the machine.
A damaged or cracked additional handle must be
replaced. Never operate a machine with a defective
additional handle.
Secure the workpiece to prevent slipping or rotation
(e.g. by securing with screw clamps).
Reducing dust exposure:
WARNING - Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- Lead from lead-based paints,
- Crystalline silica from bricks and cement and
other masonry products, and