Stiga MP 84 Series Operator's Manual

Ride-on lawnmower with seated operator

Hide thumbs Also See for MP 84 Series:

Operator's manual (788 pages)

Translation of the original instruction (59 pages)

Operator's manual (60 pages)

Table of Contents

Quick Links

Download this manual

171506066/P11

07/2023

MP 84 Series

MP 98 Series

SD 98 Series

SD 108 Series

Tosaerba con conducente a bordo seduto - MANUALE DI ISTRUZIONI

ATTENZIONE: prima di usare la macchina, leggere attentamente il presente libretto.

Косачка със седнал водач - УПЪТВАНЕ ЗА УПОТРЕБА

ВНИМАНИЕ: преди да използвате машината прочетете внимателно настоящата книжка.

Traktorska kosilica (traktorčić) - UPUTSTVO ZA UPOTREBU

PAŽNJA: prije nego što koristite ovu mašinu, pažljivo pročitajte priručnik s uputama.

Sekačka se sedící obsluhou - NÁVOD K POUŽITÍ

UPOZORNĚNÍ: před použitím stroje si pozorně přečtěte tento návod k použití.

Havetraktor - BRUGSANVISNING

ADVARSEL: læs instruktionsbogen omhyggeligt igennem, før du tager denne maskine i brug.

Aufsitzmäher (Rasenmäher mit Fahrersitz mit sitzendem Benutzer)

GEBRAUCHSANWEISUNG

ACHTUNG: vor inbetriebnahme des Geräts die Gebrauchsanleitung aufmerksam lesen.

Χλοοκοπτικό τρακτέρ με εποχούμενο χειριστή - ΟΔΗΓΙΕΣ ΧΡΗΣΠΣ

ΠΡΟΣΟΧΗ: πριν χρησιμοποιησετε το μηχανημα, διαβαστε προσεκτικα το παρον εγχειριδιο.

Ride-on lawnmower with seated operator - OPERATOR'S MANUAL

WARNING: read thoroughly the instruction booklet before using the machine.

Cortadora de pasto con conductor sentado

MANUAL DE INSTRUCCIONES

ATENCIÓN: antes de utilizar la máquina, leer atentamente el presente manual.

Istuva juhiga muruniitja - KASUTUSJUHEND

TÄHELEPANU: enne masina kasutamist lugeda tähelepanelikult antud kasutusjuhendit.

Päältäajettava ruohonleikkuri - KÄYTTÖOHJEET

VAROITUS: lue käyttöopas huolellisesti ennen koneen käyttöä.

Tondeuse à gazon à conducteur assis - MANUEL D'UTILISATION

ATTENTION: lire attentivement le manuel avant d'utiliser cette machine.

Sjedeća kosilica trave s operaterom - PRIRUČNIK ZA UPORABO

POZOR: prije uporabe stroja, pažljivo pročitajte ovaj priručnik.

Vezetőüléses fűnyírógép - HASZNÁLATI UTASÍTÁS

FIGYELEM! a gép használata előtt olvassa el figyelmesen a jelen kézikönyvet.

Table of Contents

Summary of Contents for Stiga MP 84 Series

Page 1 171506066/P11 07/2023 MP 84 Series MP 98 Series SD 98 Series SD 108 Series Tosaerba con conducente a bordo seduto - MANUALE DI ISTRUZIONI ATTENZIONE: prima di usare la macchina, leggere attentamente il presente libretto. Косачка със седнал водач - УПЪТВАНЕ ЗА УПОТРЕБА...
Page 2: Naudojimo Instrukcijos
Balninė vejapjovė su sėdinčiu operatoriumi NAUDOJIMO INSTRUKCIJOS DĖMESIO: prieš naudojant įrenginį, atidžiai perskaityti šį naudotojo vadovą. Sēžot vadāma zālienu pļaujmašīna - LIETOŠANAS INSTRUKCIJA UZMANĪBU: pirms aparāta lietošanai rūpīgi izlasiet doto instrukciju. Тревокосачка со седнат управувач - УПАТСТВА ЗА УПОТРЕБА ВНИМАНИЕ: прочитајте го внимателно ова упатство пред да ја користите машината. Grasmaaier met zittende bediener - GEBRUIKERSHANDLEIDING LET OP: vooraleer de machine te gebruiken, dient men deze handleiding aandachtig te lezen.
Page 3 ITALIANO - Istruzioni Originali ....................БЪЛГАРСКИ - Инструкция за експлоатация ................BOSANSKI - Prijevod originalnih uputa ..................ČESKY - Překlad původního návodu k používání ................DANSK - Oversættelse af den originale brugsanvisning ............... DEUTSCH - Übersetzung der Originalbetriebsanleitung ............... ΕΛΛΗΝΙΚΑ - Μεταφραση των πρωτοτυπων οδηγιων ..............ENGLISH - Translation of the original instruction ................ESPAÑOL - Traducción del Manual Original ................EESTI - Algupärase kasutusjuhendi tõlge ...
Page 4 / m i n T r a n s m i s s i o n IMPORTER FOR UK max xxx N (xx kg)
Page 6 OK ! NO !
Page 9 H = 0 mm H = 10 mm H = 20 mm H = 30 mm...
Page 12 110 mm 180 mm...
Page 13 110 mm...
Page 16: Dati Tecnici
�1� DATI TECNICI SD 98 Series SD 108 Series �2� Potenza nominale * 6,4 ÷ 11,5 6,4 ÷ 11,5 �3� Giri al minuto * 2800 ± 100 2800 ± 100 �4� Impianto elettrico 13 x 5,00-6 13 x 5,00-6 �5� Pneumatici anteriori (15 x 5,00-6) (15 x 5,00-6) �6�...
Page 17 �1� DATI TECNICI MP 84 Series MP 98 Series �2� Potenza nominale * 5,56 ÷ 9,7 6,3 ÷ 11,45 �3� Giri al minuto * 2300/2400 ± 100 2600 ± 100 �4� Impianto elettrico 13 x 5,00-6 13 x 5,00-6 �5� Pneumatici anteriori (15 x 5,00-6) (15 x 5,00-6) 18 x 8,50-8 18 x 8,50-8 �6�...
Page 18: Accessori A Richiesta
�42� ACCESSORI A RICHIESTA �42.A1� Kit “mulching”  �42.A2� �42.B� Carica batteria di mantenimento  �42.C� Kit traino  �42.D� Telo di copertura  �42.E� Kit di protezione scarico posteriore (solo per modelli MP series)  �42.F� Catene da neve (18”)  �42.G� Ruote da fango/neve (18”)  �42.H� Rimorchio 45-03453-997 �42.I�...
Page 19 [1] BG - ТЕХНИЧЕСКИ ДАННИ [1] BS - TEHNIČKI PODACI [1] CS - TECHNICKÉ PARAMETRY [2] Н оминална мощност * [2] N azivna snaga (*) [2] J menovitý výkon (*) [3] О бороти в минута (*) [3] Obrtaji u minuti (*) [3] Otáčky za minutu (*) [4] ...
Page 20 [1] DA - TEKNISKE DATA [1] DE - TECHNISCHE DATEN [1] EL - ΤΕΧΝΙΚΑ ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ [2] N ominel effekt (*) [2] N ennleistung (*) [2] Ο νομαστική ισχύς (*) [3] Omdrejninger pr. minut (*) [3] U mdrehungen pro Minute (*) [3] Σ τροφές ανά λεπτό (*) [4] Elektrisk anlæg [4] ...
Page 21 [1] EN - TECHNICAL DATA [1] ES - DATOS TÉCNICOS [1] ET - TEHNILISED ANDMED [2] N ominal power (*) [2] P otencia nominal (*) [2] N ominaalvõimsus (*) [3] R PM (*) [3] R evoluciones por minuto (*) [3] P öörded minutis (*) [4] E lectrical system [4] ...
Page 22 [1] FI - TEKNISET TIEDOT [1] FR - CARACTÉRISTIQUES TECH- [1] HR - TEHNIČKI PODACI [2] N imellisteho (*) NIQUES [2] N azivna snaga (*) [3] K ierrosta minuutissa (*) [2] P uissance nominale (*) [3] B roj okretaja u minuti (*) [4] S ähkölaitteisto [3] ...
Page 23 [1] HU - MŰSZAKI ADATOK [1] LT - TECHNINIAI DUOMENYS [1] LV - TEHNISKIE DATI [2] N évleges teljesítmény (*) [2] V ardinė galia (*) [2] N ominālā jauda (*) [3] P ercenkénti fordulatszám (*) [3] A psisukimai per minutę (*) [3] Apgriezieni minūtē (*) [4] ...
Page 24 [1] MK - ТЕХНИЧКИ ПОДАТОЦИ [1] NL - TECHNISCHE GEGEVENS [1] NO - TEKNISKE DATA [2] Н оминална моќност (*) [2] N ominaal vermogen (*) [2] N ominell effekt (*) [3] В ртежи во минута (*) [3] O mwentelingen per minuut [3] O mdreininger pr. minutt (*) [4] ...
Page 25 [1] PL - DANE TECHNICZNE [1] PT - DADOS TÉCNICOS [1] RO - DATE TEHNICE [2] M oc znamionowa (*) [2] P otência nominal (*) [2] P utere nominală (*) [3] L iczba obrotów na minutę (*) [3] R otações por minuto (*) [3] R otații pe minut (*) [4] I nstalacja elektryczna [4] ...
Page 26 [1] RU - ТЕХНИЧЕСКИЕ [1] SK - TECHNICKÉ PARAMETRE [1] SL - TEHNIČNI PODATKI ХАРАКТЕРИСТИКИ [2] M enovitý výkon (*) [2] N azivna moč (*) [2] Н оминальная мощность (*) [3] Otáčky za minútu (*) [3] Vrtljaji na minuto (*) [3] Ч исло оборотов в минуту (*) [4] ...
Page 27 [1] SR - TEHNIČKI PODACI [1] SV - TEKNISKA SPECIFIKATIONER [1] TR - TEKNİK VERİLER [2] N azivna snaga (*) [2] N ominell effekt (*) [2] N ominal güç (*) [3] O brtaji u minuti (*) [3] V arv i minuten (*) [3] D akikadaki devir sayısı (*) [4] ...
Page 28 WARNING!: READ THOROUGHLY THE INSTRUCTION BOOKLET BEFORE USING THE MACHINE. Keep for future reference INDEX 1. GENERAL INFORMATION ......2 7.6 Battery ..........17 2. SAFETY REGULATIONS ......2 7.7 Nuts and bolts ........18 3. GETTING TO KNOW THE MACHINE ... 4 8.
Page 29: General Information
how to stop the engine quickly. Failure 1. GENERAL INFORMATION to follow the warnings and instructions may result in fire and/or serious injury. HOW TO READ THE MANUAL • Never allow children or persons unfamiliar with these instructions to Some paragraphs in the manual contain use the machine. Local regulations important information regarding safety and may restrict the age of the operator. operation and are emphasized in this manner: • Never use the machine if the user is tired or unwell, or has taken medicine, drugs, NOTE or IMPORTANT these give details alcohol or any substances which may slow ...
Page 30: During Operation
• Do not smoke when filling up with • Pay attention on sloping ground which fuel or when handling the fuel. requires particular care to prevent overturning • Use a funnel to top up with or loss of control of the machine. The fuel only in the open air. main reasons for loss of control are: • Do not inhale fuel fumes. – Insufficient wheel grip • Never remove the tank cap or add – Excessive speed fuel while the engine is running – Inadequate braking or when the engine is hot. – Type of machine unsuitable for its task • Open the fuel tank slowly to allow the – Lack of awareness of the effect of pressure inside to decrease gradually. ground conditions, especially slopes • Do not approach the tank opening with – Incorrect use as a towing machine. a naked flame to check its contents. • If you have spilled some fuel, do not attempt to Behaviour start the engine but move the machine away ...
Page 31: Maintenance & Storage
Use limitations 2.5 ENVIRONMENTAL PROTECTION • Never operate the machine with guards damaged, missing or incorrectly Safeguarding the environment must be a relevant assembled (grass catcher, side discharge and priority aspect of machine use, of benefit to guards rear discharge guards) the community and the environment we live in. • Don’t use the machine if the attachments/ • Avoid being a disturbance to the tools are not installed in their seats. neighbourhood. Use this machine at • Never disengage, deactivate, remove reasonable times of the day only (not or tamper with the safety systems/ early morning or late evening when the microswitches installed. noise could cause disturbance).
Page 32: Safety Signs
1. mow the grass and collect it IMPORTANT The machine must in the grass catcher be used by one operator. 2. mow the grass and discharge it on the ground from the rear section 3. mow, chop and deposit the grass 3.2 SAFETY SIGNS on the ground (mulching effect). • SD 98 / 108 Series can: The machine has various symbols on it 4. mow the grass and discharge it from the side (fig. 2 ) . They are used to remind the operator 5. mow, chop and deposit the grass of the behaviour to follow to use it with on the ground (mulching effect). the necessary attention and caution. Meaning of symbols: The use of special attachments provided for Warning: Read the instruc- by the Manufacturer as original equipment or ...
Page 33: Identification Label
E. Grass catcher: as well as collecting the Warning! Never use pressure grass cuttings, this is also a safety element lances to wash the transmis- that stops any objects drawn up by the sion system. cutting devices from being hurled away from the machine (for rear collection models only). Rear discharge guard (available upon IMPORTANT Any damaged or illegible request): this can be fitted in place of the decals must be replaced. Order replacement grass catcher and prevents objects from decals from an authorised assistance centre. being drawn up by the cutting means ...
Page 34 steering wheel in place using the screws Front bumpers supplied (fig. 3.G) in the indicated order. Anti-chipping wheels 5b. For type "ll" steering wheel only - Fasten Grass catcher with relative assembly the steering wheel in place using the screws screws and instructions (for models (fig. 3.F, 3.G) supplied, in the indicated order. with rear collection only) 6. Fit the steering wheel cover (fig. 3.H) Lower part of the rear plate, the grass by clicking the fasteners into place. catcher brackets and attachments nec- essary for completing and assembly (for 4.3 SEAT ASSEMBLY rear collection models only) Side discharge chute (for models with Fit the seat (fig. 4.A) onto the plate (fig. 4.B) using ...
Page 35: Key Ignition Switch
2. Position the side discharge chute (fig. 2. Remove the two screws (fig. 9.H), 7.A) in line with the cutting-means which will be used later. assembly brackets (fig. 7.C). Using a 3. Assemble the lower part (fig. 9.E) of the screwdriver, turn the second terminal rear plate and fasten it to the lower brackets (fig. 7.B.2) of the spring (fig. 7.B) to bring with the screws (fig. 9.F) and bolts (fig. it outside the side discharge chute. 9.G), without tightening them completely. 3. Fit the pin (fig. 7.D) in the holes on the 4. Finish fastening the lower part (fig. 9.E) of brackets (fig. 7.C) and on the side discharge the rear plate, completely tightening the two chute, so that it passes through the coils central screws (fig. 9.H) that you previously ...
Page 36: Parking Brake Lever
1. Choke Command - Cold start. 5.5 SPEED CHANGE LEVER Used to turn on the engine when cold. (MECHANICAL DRIVE) The «CHOKE» position enriches the mixture so it must only be used for This lever has seven positions (fig. 10.K): the time necessary for cold starts. 1. Maximum engine speed. To 1. 5 forward gears be used always when starting Gear must only be engaged the machine, while it is On and when the machine has stopped. during grass cutting operations.
Page 37: Using The Machine
3. Neutral position. The pedal 5.10 REVERSE GEAR CUTTING automatically goes into neutral CONSENT BUTTON position when released. By pressing and holding this button (fig. 10.F), it is possible to switch to reverse NOTE If the drive pedal is used, whether gear with the cutting means engaged forwards or for reverse, when the parking brake without causing the engine to stop. (fig. 10.D) is engaged, the engine stops. 5.11 CUTTING HEIGHT ADJUSTER LEVER 5.8 HYDROSTATIC TRANSMISSION DISENGAGEMENT LEVER...
Page 38: Safety Checks
with the rear plate. Centring is ensured by 6.1 PREPARATION using the right bracket as lateral support. – Make sure that the lower pipe Before starting to mow, it is necessary to carry of the grass catcher opening is out several checks and operations to ensure you attached to the pawl (fig. 15.C). can work efficiently and in maximum safety. c. Prepare the machine for rear cutting and 6.1.1 Filling with oil and fuel discharge of the grass onto the floor (for models with rear collection only) IMPORTANT The machine is –...
Page 39: Using On Slopes
6.3 USING ON SLOPES Drive the machine The machine slows forwards and backwards, down and stops shift to neutral / Comply with the limits indicated in the release the drive pedal "Technical Data" Tables ad in "fig. 19" (par. 5.5; par. 5.7) regardless of the mowing direction. Press the brake pedal The machine stops (par. 5.4; par. 5.6) Remember there is no such thing as a "safe” Test driving No abnormal vibrations. slope. Driving on grass slopes requires No abnormal sound particular care. To prevent overturning Safety devices Proceed as indicated or loss of control over the machine: in par. 6.2.2 •...
Page 40: Operation
8. Insert the ignition key and turn to On • For models with mechanical drive only: to make electrical contact, then turn 1. Press the pedal all the way down it to Start to start the engine. (par. 5.4) and shift the gear 9. Release the ignition key once lever to 1st gear (par. 5.5). the engine has started. 2. Hold the pedal down (fig. 10.1) then 10. If cold starting: as soon as the disengage the parking brake (par. 5.3).
Page 41 a solid grassy bed. If the lawn is cut is For models with mechanical drive only: less frequently, higher grass and weeds 1. Press the pedal (par. 5.4) until start growing (clover and daisies, etc.). the machine comes to a stop; 2. It is always better to cut the grass when dry. 2. Shift the gear lever to "R" 3. The cutting means must be in good reverse (par. 5.5). condition and well sharpened so that 3. Gradually release the pedal to engage the the grass is cut straight without a ragged clutch and then begin moving in reverse. edge that leads to yellowing at the ends. 4. The engine must run at full speed, both For models with hydrostatic drive only: to ensure a sharp cut of the grass and 1.
Page 42: After Operation
4. engage the parking brake; ignition key (checking that all moving 5. stop the engine; parts are completely stationary): 6. pull out the lever (fig. 23.A - if fitted) or – whenever the machine is left unattended, grasp the rear handle (fig. 23.A1) and the operator dismounts from the tip up the grass catcher to empty it; driving seat, or parks the machine; 7. close up the grass catcher so that it hooks onto the pawl (fig. 23.B). 7. ROUTINE MAINTENANCE 6.5.7 Cleaning the discharge chute (for rear collection models only) GENERAL INFORMATION • Cutting very tall or wet grass, particularly at excessively high speed, can clog up ...
Page 43 7.2.1 Refuelling 7.3.1 Check/top-up To refuel: Always check the oil level before use. 1. Unscrew the tank closure cap and remove it (fig. 25). • Check the oil level: according to the 2. Insert the funnel (fig. 25). instructions in the engine manual, this 3. Refuel being careful not to must be between the MIN and MAX completely fill the tank. marks on the dipstick (fig. 26). 4. Remove the funnel. 5. Close the fuel cap securely after Do not overfill as this could cause refuelling and clean away any spills.
Page 44 6. Refit the extension tube (fig. 28.A) on the IMPORTANT Never use hose-nozzles or harsh support (fig. 28.C) before topping up the oil. detergents for cleaning the body and engine! 7. Clean up any spills. IMPORTANT Do not wash the IMPORTANT Hand the spent transmission system when it is hot. oil over to a disposal facility in Never use pressure lances to wash the accordance with local provisions.
Page 45: Nuts And Bolts
– follow the instructions in the battery manual; IMPORTANT In order not to compromise NUTS AND BOLTS the efficiency of the electromagnetic clutch: - do not let the clutch come into contact with oil; • Keep all nuts, bolts and screws tight to be sure - do not spray pressurised water the equipment is in safe working condition.
Page 46 IMPORTANT Always use original 8.3.3 Choice and positioning of the cutting means bearing the code jack on the front wheels indicated in the “Technical Data”. 1. Position some wooden wedges (fig. 37.A) Given product evolution, the cutting means to the wheel base (fig. 37.B) behind listed in the "Technical Data" table may be the wheel to be changed (fig. 37.C). replaced in time with others having similar 2. The maximum possible jack height interchangeable and operating safety features. when closed is 110 mm. 3. Position a square 10 x 10 cm wooden 8.3 REPLACING OF FRONT wedge (fig. 38.B) on the jack (fig. 38.A). ...
Page 47: Electronic Circuit Board
8.4 ELECTRONIC CIRCUIT BOARD REPLACING BULBS The electronic circuit board is a component fitted below the dashboard which 8.6.1 Type "l" - Incandescent light bulbs manages all machine safety devices. • The bulbs (18W) have a bayonet fitting 8.4.1 Electronic circuit board and are installed in the bulb holder protection device (for rear which can be taken out by turning it collection models only) anti-clockwise with pliers (fig. 42). • The electronic circuit board is located 8.6.2 Type "ll"...
Page 48: Handling And Transportation
• The authorized service workshops 10. HANDLING AND TRANSPORTATION only use genuine spare parts. Genuine spare parts and attachments have been • When handling the machine, always: designed specifically for machines. – disengage the cutting means; • Non-original parts and attachments are – bring the cutting-means assembly not approved; use of non-original spare to the highest position; parts and attachments will jeopardize – stop the engine; the safety of the machine and relieve the Manufacturer from all obligations or liabilities. • When transporting the machine • It is advisable to send your machine on a vehicle or trailer, always: once a year to an authorized service – use an access ramp of suitable workshop for servicing, assistance strength, width and length; and safety device inspection. – load the machine with the engine switched off, with the key removed from the ignition, without a driver and pushed 12. WARRANTY COVERAGE by an adequate number of people;...
Page 49: Problem Identification
Operation Frequency Completed (Date or Hours) Notes (hours) MACHINE Safety checks/check controls Before par. 6.2 each use Tyre pressure check Before par. 6.1.3 each use Assembly/Checking of outlet guards Before par. 6.1.4 each use General cleaning and inspection After each par. 7.4 Checking for any damage to the After each machine. If necessary, contact the authorised assistance centre. Before Battery power reserve par.
Page 50 1. With the key turned to The safety device of the electronic Turn the ignition key to «STOP» position «ON», the light stays circuit board has cut in due to: and look for the cause of the problem: off (for rear collection badly connected battery check the connections (par. 4.4) models only battery terminals crossed check the connections (par. 4.4). flat battery recharge the battery (par. 7.5) fuse blown replace fuse (10 A) (par. 8.5). wet circuit board dry using luke warm air 2. With the key turned starting conditions have not been met check that all starting conditions are met to «START» the light (par.
Page 51 PROBLEM PROBABLE CAUSE REMEDY 4. With the key turned to Turn the ignition key to «STOP» position «START» the starter and look for the cause of the problem: motor does not run starting conditions have not been met check that all starting conditions are met (for side discharge (par. 6.2.2) models only) badly connected battery check the connections (par. 4.4) battery terminals crossed check the connections (par. 4.4) flat battery recharge the battery (par. 7.5) fuse blown replace fuse (10 A) (par. 8.5). wet circuit board dry using luke warm air malfunction on the starter relay contact your Dealer 5. With the key on insufficiently charged battery recharge the battery (par. 7.5) «START»...
Page 52 PROBLEM PROBABLE CAUSE REMEDY 11. Uneven mowing and cutting-means assembly is check the tyre pressure (par. 6.1.3) insufficient collection not parallel to the ground reinstate the alignment of the (for rear collection cutting-means assembly in relation models only) to the ground (par. 8.2.1) i nefficient cutting means contact your Dealer forward speed too high reduce the forward speed and/or raise compared to height of grass the cutting-means assembly (par. 6.5.4) wait for the grass to dry collector channel is blocked remove the grass catcher and empty the discharge chute (par. 7.4.2) 12.
Page 53 15. ATTACHMENTS 15.1 "MULCHING" KIT 15.7 18" MUD / SNOW WHEELS It finely chops the grass cuttings and leaves These improve drive performance them on the lawn (fig. 43.A1; fig 43.A2). on snow and mud. 15.2 MAINTENANCE BATTERY CHARGER 15.8 TRAILER This keeps the battery in good working For transporting tools and other objects order when the machine is in storage, within the allowed load limits (fig. 43.H). guaranteeing an optimum level of charge and longer battery life (fig. 43.B). 15.9 SPRINKLER 15.3 TOWING KIT To sprinkle salt or fertilisers (fig. 43.I). To tow a small trailer (fig. 43.C). 15.10 GRASS ROLLER 15.4 CANVAS COVER To make the soil compact after seeding ...
Page 54 Livello di potenza sonora garantito: 100 dB(A) i) Ampiezza di taglio: 83 cm ST. S.p.A. n) Persona autorizzata a costituire il Fascicolo Tecnico: Via del Lavoro, 6 31033 Castelfranco Veneto (TV) - Italia o) Castelfranco Veneto, 01/10/2022 CEO Stiga Group Sean Robinson 171512690/13...
Page 55 ST. S.p.A. n) Person authorised to compile the technical file: Via del Lavoro, 6 31033 Castelfranco Veneto (TV) - Italia o) Castelfranco Veneto, 01/10/2022 CEO Stiga Group Sean Robinson UK Importer: STIGA LTD Unit 8, Bluewater Estate Plympton, Devon, PL7 4JH, England...
Page 56 Livello di potenza sonora garantito: 100 dB(A) i) Ampiezza di taglio: 97 cm ST. S.p.A. n) Persona autorizzata a costituire il Fascicolo Tecnico: Via del Lavoro, 6 31033 Castelfranco Veneto (TV) - Italia o) Castelfranco Veneto, 01/10/2022 CEO Stiga Group Sean Robinson 171512718/10...
Page 57 ST. S.p.A. n) Person authorised to compile the technical file: Via del Lavoro, 6 31033 Castelfranco Veneto (TV) - Italia o) Castelfranco Veneto, 01/10/2022 CEO Stiga Group Sean Robinson UK Importer: STIGA LTD Unit 8, Bluewater Estate Plympton, Devon, PL7 4JH, England...
Page 58 Livello di potenza sonora garantito: 100 dB(A) i) Ampiezza di taglio: 98 cm ST. S.p.A. n) Persona autorizzata a costituire il Fascicolo Tecnico: Via del Lavoro, 6 31033 Castelfranco Veneto (TV) - Italia o) Castelfranco Veneto, 01/10/2022 CEO Stiga Group Sean Robinson 171512692/11...
Page 59 ST. S.p.A. n) Person authorised to compile the technical file: Via del Lavoro, 6 31033 Castelfranco Veneto (TV) - Italia o) Castelfranco Veneto, 01/10/2022 CEO Stiga Group Sean Robinson UK Importer: STIGA LTD Unit 8, Bluewater Estate Plympton, Devon, PL7 4JH, England...
Page 60 Livello di potenza sonora garantito: 100 dB(A) i) Ampiezza di taglio: 107 cm ST. S.p.A. n) Persona autorizzata a costituire il Fascicolo Tecnico: Via del Lavoro, 6 31033 Castelfranco Veneto (TV) - Italia o) Castelfranco Veneto, 01/10/2022 CEO Stiga Group Sean Robinson 171512695/11...
Page 61 ST. S.p.A. n) Person authorised to compile the technical file: Via del Lavoro, 6 31033 Castelfranco Veneto (TV) - Italia o) Castelfranco Veneto, 01/10/2022 CEO Stiga Group Sean Robinson UK Importer: STIGA LTD Unit 8, Bluewater Estate Plympton, Devon, PL7 4JH, England...
Page 62 FR (Traduction de la notice originale) EN (Translation of the original instruction) DE (Übersetzung der Originalbetriebsanleitung) Déclaration CE de Conformité EC Declaration of Conformity (Directive Machines 2006/42/CE, Annexe II, (Machine Directive 2006/42/EC, Annex II, EG-Konformitätserklärung partie A) part A) (Maschinenrichtlinie 2006/42/EG, Anhang 1.
Page 63 NO (Oversettelse av orginal bruksanvisning) SV (Översättning av bruksanvisning i original) DA (Oversættelse af den originale brugsanvisning) EF- Samsvarserklæring EG-försäkran om överensstämmelse (Maskindirektiv 2006/42/EF, Vedlegg II, del (Maskindirektiv 2006/42//EG, bilaga II, de EF-overensstemmelseserklæring (Maskindirektiv 2006/42/EF, bilag II, del A) 1. Firmaet 1.
Page 64 SL (Prevod izvirnih navodil) BS (Prijevod originalnih uputa) SK (Preklad pôvodného návodu na použitie) ES izjava o skladnosti EZ izjava o sukladnosti ES vyhlásenie o zhode (Direktiva 2006/42/ES) , priloga II, del A) (Direktiva o mašinama 2006/42/EZ, Prilog (Smernica o Strojných zariadeniach 1.
Page 65 © by ST. S.p.A. IT • Il contenuto e le immagini del presente manuale d’uso sono stati realizzati per conto di ST. S.p.A. e sono tutelati da diritto d’autore – E’ vietata ogni riproduzione o alterazione anche parziale non autorizzata del documento. BG • Съдържанието и изображенията в настоящото ръководство са извършени за ST. S.p.A. и са защитени с авторски права – Забранява се всяко неоторизирано възпроизвеждане или промяна, дори и отчасти на документа. BS • Sadržaj i slike iz ovog korisničkog priručnika napravljeni su isključivo za ST. S.p.A. i zaštićeni su autorskim pravima – zabranjena je svaka neovlaštena reprodukcija ili izmjena dokumenta, djelomično ili u potpunosti. CS • Obsah a obrázky v tomto návodu k použití byly zpracovány jménem společnosti ST. S.p.A. a jsou chráněny autorským právem – Reprodukce či nepovolené pozměňování tohoto dokumentu, a to i částečné, je zakázáno. DA • Indhold og illustrationer i denne vejledning er blevet skabt på vegne af ST. S.p.A. og er beskyttet af ophavsret – Enhver gengivelse eller ændring, også delvis, af dokumentet uden autorisation hertil er forbudt. DE • Inhalt und Bilder dieser Bedienungsanleitung wurden im Namen von ST. S.p.A. erstellt und sind urheberrechtlich geschützt – Jede nicht genehmigte Vervielfältigung oder Veränderung, auch auszugsweise, dieses Dokuments ist verboten. EL • Το περιεχόμενο και οι εικόνες στο παρόν εγχειρίδιο χρήσης δημιουργήθηκαν για λογαριασμό της εταιρείας ST. S.p.A. και προστατεύονται από πνευματικά δικαιώματα – Απαγορεύεται οποιαδήποτε αναπαραγωγή ή τροποποίηση, έστω και μερική, του εγγράφου χωρίς έγκριση. EN • The content and images in this User Manual were produced expressly for ST. S.p.A. and are protected by copyright – any unauthori- sed reproduction or modification to the document, either partially or in full, is prohibited. ES • El contenido y las imágenes del presente manual de uso han sido creados por ST. S.p.A. y están protegidos por los derechos de autor – Se prohíbe toda reproducción o modificación, incluso parcial, no autorizada del documento. ET • Käesoleva kasutusjuhendi sisu ja kujutised on toodetud konkreetselt ettevõttele ST. S.p.A. ja neile rakendub autorikaitseseadus – dokumendi igasugune osaline või täielik ilma loata reprodutseerimine või muutmine on keelatud. FI • Tämän käyttöoppaan sisältö ja kuvat on valmistettu ST. S.p.A. -yhtiön toimesta ja niitä suojaa tekijänoikeuslaki. – Asiakirjan kaikenlai- nen kopioiminen tai muuttaminen, osittainkin, on kielletty ilman erityistä lupaa. FR • Le contenu et les images du présent manuel d’utilisation ont été réalisés pour le compte de ST. S.p.A. et sont protégés par un droit d’auteur - Toute reproduction ou modification non autorisée, même partielle, du document, est interdite. HR • Sadržaj i slike u ovom priručniku za uporabu izrađeni su za tvrtku ST. S.p.A. te su obuhvaćeni autorskim pravima – Zabranjuje se neovlašteno umnožavanje ili prilagodba, djelomična ili u cijelosti, ovog dokumenta. HU • Ennek a használati útmutatónak a tartalma és a benne szereplő képek kizárólag a ST. S.p.A. számára készültek és szerzői joggal védettek – tilos a dokumentum bármely részének vagy egészének engedély nélküli sokszorosítása és módosítása. LT • Šio naudotojo vadovo turinys ir paveikslėliai skirti tik „ST. S.p.A.“ ir yra saugomi autorių teisėmis – dokumentą atgaminti ar modifikuoti, visiškai arba iš dalies, yra draudžiama. LV • Šīs lietotāja rokasgrāmatas saturs un attēli ir veidoti tikai ST. S.p.A. un ir aizsargāti ar autortiesībām. Jebkāda dokumenta vai tā daļas prettiesiska kopēšana vai pārveide ir stingri aizliegta. MK • Содржината и сликите во Упатството за корисникот се подготвени исклучиво за ST. S.p.A. и се заштитени со авторски права – забрането е секое делумно или целосно неовластено репродуцирање или измена на документот. NL • De inhoud en de afbeeldingen van deze gebruikshandleiding werden gerealiseerd voor rekening van ST. S.p.A. en zijn beschermd door het auteursrecht – Elke niet-geautoriseerde reproductie of wijziging, ook gedeeltelijke, van het document is verboden. NO • Innholdet og bildene i denne brukerveiledningen er utført på oppdrag fra ST. S.p.A. og er beskyttet ved opphavsrett - Enhver gjengi- velse eller endring, selv kun delvis, er forbudt. PL • Treść oraz ilustracje zawarte w niniejszej instrukcji obsługi powstały na zlecenie spółki ST. S.p.A. i są chronione prawami autorskimi – ...
Page 66 Points de collecte sur www.quefairedemesdechets.fr Privilégiez la réparation ou le don de votre appareil ! ST. S.p.A. STIGA LTD (UK Importer) Via del Lavoro, 6 Unit 8, Bluewater Estate Plympton, 31033 Castelfranco Veneto (TV) ITALY Devon, PL7 4JH, England...

This manual is also suitable for:

Mp 98 series Sd 98 series Sd 108 series Estate 384 m

Stiga MP 84 Series Operator's Manual

Quick Links

Related Manuals for Stiga MP 84 Series

Summary of Contents for Stiga MP 84 Series

This manual is also suitable for:

Table of Contents