Table of Contents
Advertisement
Quick Links
Wall Mount Wi-Fi
Install On Sectional Doors With Torsion Assemblies Only
This product is intended for installation only by trained garage door technicians. This product may
require adjustments to door springs and/or track configurations. This product is not intended
for use on low headroom tracks with outside pick up drums or garage doors utilizing extension
springs.
• Please read this manual and the
enclosed safety materials carefully!
• The door WILL NOT CLOSE unless the
Protector System
properly aligned.
• Periodic checks of the garage door opener
are required to ensure safe operation.
• The model number is located on the
front cover of the opener.
• This garage door opener is ONLY
compatible with myQ
and Security+ 3.0
• Attach warning labels to the location
indicated on label.
LiftMaster
300 Windsor Drive
Oak Brook, IL 60523
Models 93002MC, 93002-VKP1MC
For Residential Use
is connected and
®
, Security+ 2.0
®
accessories.
®
Garage Door Opener
®
Register your garage door opener to receive
updates and offers from LiftMaster
,
®
Take a photo of the
camera icon including
the points ( ).
Send it in by texting
the photo to 71403
(US) or visit
www.Liftmaster.photo
(Global)
Advertisement
Table of Contents
Related Manuals for Chamberlain 93002MC
Summary of Contents for Chamberlain 93002MC
- Page 1 Wall Mount Wi-Fi Garage Door Opener ® Models 93002MC, 93002-VKP1MC For Residential Use Install On Sectional Doors With Torsion Assemblies Only This product is intended for installation only by trained garage door technicians. This product may require adjustments to door springs and/or track configurations. This product is not intended for use on low headroom tracks with outside pick up drums or garage doors utilizing extension springs.
-
Page 2: Table Of Contents
Table of Contents PREPARATION Install Automatic Door Lock ....... 10 PROGRAMMING myQ Serial Number ........2 Install the Door Control 893MAX Remote Control ......28 Safety Symbol and Signal Word Review ..2 (Smart Control Panel ) ....... 12 ® Reprogramming myQ Remote Unattended Operation ........ -
Page 3: Planning
Preparation Planning Survey your area to see if any of the conditions below apply to your installation. NOTE: Inspect the torsion bar while the Depending on your requirements, additional materials may be required. door is raised and lowered. It is important that there is no noticeable movement up THIS DOOR OPENER IS COMPATIBLE WITH: and down or left and right. -
Page 4: Before You Connect With Your Smartphone
Preparation Before You Connect with Your Smartphone Monitor and control your garage door from anywhere using the myQ app. BEFORE YOU BEGIN: You will need: • Wi-Fi enabled smartphone, tablet or laptop • Broadband Internet Connection • Wi-Fi signal in the garage (2.4 Ghz, 802.11b/g/n required) •... -
Page 5: Preparing Your Garage Door
Preparation Preparing Your Garage Door BEFORE YOU BEGIN: To prevent possible SERIOUS INJURY or DEATH: • ALWAYS call a trained door systems technician if garage door binds, sticks, or is • Disable locks. out of balance. An unbalanced garage door may NOT reverse when required. •... -
Page 6: Carton Inventory
Preparation Carton Inventory If anything is missing, carefully check the packing material. 2 Conductor Bell Wire White and White/Red Automatic Garage Door Lock Model 841LM with 2-Conductor White and White/Black Bell Wire with Connector NOTE: Older model 24V door locks Collar with are incompatible Set Screws... -
Page 7: Assembly
Assembly Attach the Collar to the Garage Door Opener To avoid installation difficulties, do not run the garage door garage door opener until instructed to do so. To prevent possible SERIOUS INJURY or DEATH, the collar MUST be properly The garage door opener can be installed on either side of the door (see Planning section tightened. -
Page 8: Attach Mounting Bracket To Garage Door Opener
Assembly Attach Mounting Bracket to Garage Door Opener HARDWARE Loosely attach slotted side of mounting bracket to the same side of the garage door Screw opener as the collar, using screws provided. #10-32 (2) NOTE: Do not tighten screws until instructed. Socket Wrench Installation IMPORTANT INSTALLATION INSTRUCTIONS... -
Page 9: Position And Mount The Garage Door Opener
Installation Position and Mount the Garage Door Opener NOTE: For additional mounting options refer to the accessories page. Close the garage door completely. To prevent possible SERIOUS INJURY Slide the garage door opener onto the end of the torsion bar. If the torsion bar is too or DEATH: long or damaged, you may need to cut the torsion bar. -
Page 10: Attach The Emergency Release Rope And Handle
Installation Attach the Emergency Release Rope and Handle Insert one end of the emergency release rope through the handle. Make sure that To prevent possible SERIOUS INJURY “NOTICE” is right side up. Secure with an overhand knot at least 1" (2.5 cm) from or DEATH from a falling garage door: the end of the rope to prevent slipping. - Page 11 Installation Attach the Cable Tension Monitor (Required) The cable tension monitor MUST be NOTE: The cable tension monitor is shipped for left side installation. It is recommended connected and properly installed before that the cable tension monitor be installed on the same side of the door as the door the garage door opener will move in the opener.
-
Page 12: Install The Door Control (Smart Control Panel ® )
Installation Install the Door Control (Smart Control Panel ® Install door control within sight of garage door, out of reach of small children at a To prevent possible SERIOUS INJURY or minimum height of 5 feet (1.5 m) above floors, landings, steps or any other adjacent DEATH from electrocution: walking surface, and away from ALL moving parts of door. -
Page 13: Install Myq Remote Led Light
Installation IMPORTANT INSTALLATION INSTRUCTIONS To reduce the risk of SEVERE INJURY or DEATH: • This portable luminaire has a polarized plug (one blade •. DO NOT alter the plug. is wider than the other) as a feature to reduce the risk of •. -
Page 14: Install The Protector System
Installation (continued) Install the Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door will move in the down direction. This is a required safety device and Be sure power is NOT connected to the cannot be disabled. - Page 15 Installation (continued) INSTALLING THE BRACKETS The brackets house the safety reversing sensors in a fixed, secure position so the safety reversing sensors will face each other across the garage door, with the beam no higher than 6" (15 cm) above the floor. Be sure power to the opener is disconnected. Choose one of the following installations.
- Page 16 Installation (continued) MOUNTING THE SAFETY REVERSING SENSORS HARDWARE 1. Slide a 10-24 hexagonal screw into the slot on each sensor. 2. Use wing nuts to fasten safety reversing sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not Hexagonal Screw 10-24 (2) obstructed by a bracket extension.
-
Page 17: Connect Power
RIGHT WRONG RIGHT WRONG Installation (continued) PERMANENT WIRING PERMANENT WIRING CONNECTION CONNECTION Connect Power Ground Tab Ground Tab Green Green To avoid installation difficulties, do not Ground Screw Ground Screw run the garage door opener at this time. To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: Black Black •... - Page 18 Installation (continued) Align the safety reversing sensors The door will not close if the sensors have not been installed and aligned correctly. The LEDs in both sensors must be glowing steady, which indicates they are powered and aligned correctly. The sending sensor (with an amber LED) transmits an invisible light beam to the receiving sensor (with a green LED).
-
Page 19: Install The Battery Backup
Installation Install the Battery Backup When in Battery Backup mode, myQ Smartphone Control and wireless myQ devices To reduce the risk of FIRE or INJURY will be disabled. In battery backup mode, the automatic garage door lock will unlock to persons: when the garage door is opened, and will remain disabled until power is restored. -
Page 20: Adjustment
Adjustment Program the Travel Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system. •... -
Page 21: Test The Safety Reversal System
Adjustment Test the Safety Reversal System Test the Protector System ® Without a properly installed safety reversal system, persons Without a properly installed safety reversing sensor, persons (particularly small children) could be SERIOUSLY INJURED or (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. -
Page 22: Test Cable Tension Monitor
NOTE: The power door lock can be manually released by sliding the manual release handle to the open position. However, if the power door lock does not function, contact Chamberlain for a replacement. Power Door Lock Power Door Lock Manual Release... -
Page 23: Operation
Operation IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of SEVERE INJURY or DEATH: 1. Read and follow all warnings and instructions. 9. After ANY adjustments are made, the safety reversal system MUST be tested. 2. ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with garage 10. -
Page 24: Using Your Garage Door Opener
Operation Using Your Garage Door Opener FEATURES THE PROTECTOR SYSTEM (SAFETY USING YOUR GARAGE DOOR REVERSING SENSORS) OPENER Your garage door opener is equipped with features to provide you with greater control When properly connected and aligned, The garage door opener can be activated over your garage door operation. -
Page 25: Connect With Your Smartphone
Operation Connect With Your Smartphone The Wi-Fi Garage Door Opener is compatible with up to 16 myQ enabled accessories. Up to 10 devices can be paired to the Wi-Fi garage door opener’s internal gateway. These devices can be controlled with the myQ app. These devices include any combination of myQ garage door openers, Wi-Fi garage door openers, myQ light controls, myQ gate operators or myQ commercial door operators. -
Page 26: Using The Door Control
Operation Using the Door Control SYNCHRONIZE THE DOOR CONTROL To synchronize the door control to the garage door opener, press the push bar until the garage door opener activates (it may take up to 3 presses). Test the door control by pressing the push bar, each press of the push bar will activate the garage door opener. Up to 2 Smart Control Panels or 4 of any other Screen Security+ 2.0 door controls can be connected to the... - Page 27 Operation SETUP The features on the door control can be programmed through a series of menus on the screen and the navigation buttons. Refer to the descriptions below. SCREEN The main screen displays the time, temperature, and current battery charge (if Navigation Buttons applicable) Set the time, choose 12 or 24 hour clock and...
-
Page 28: Programming 893Max Remote Control
Programming 893MAX Remote Control Your remote control has been programmed at the factory to operate with your garage door opener. If the remote does not work or you would like to program additional devices, follow the programming steps below. Up to 40 Security+ 2.0 remote controls can be programmed to the garage door opener. Older LiftMaster remote controls are NOT compatible, see page 37 for compatible accessories. -
Page 29: Led Light
Programming Program the myQ Remote LED Light Your garage door opener remote light has already been programmed at the factory to operate with your opener. Any additional or replacement remote lights will need to be programmed. PROGRAM A DOOR OPENER TO THE myQ REMOTE LED LEARN Button LIGHT Press the LEARN button on the light until the green LED...