Table of Contents
Advertisement
Insert the top panel at an angle towards the back into the
2.
brackets. The smooth surface must face outwards. (fig. B).
Troubleshooting
Malfunctions often have simple explanations. Refer to the table
before calling the after-sales service as you may be able to
remedy the fault yourself.
Malfunction table
If a dish does not turn out as well as you had hoped, refer to
the section Tested for you in our cooking studio, where you will
find plenty of cooking tips and notes.
Problem
Possible cause Remedy/information
The oven does
The circuit
not work.
breaker is
defective.
Power cut
Power cut
and zeros
0
flash in the dis-
play.
The oven does
There is dust on
not heat up.
the contacts.
Error messages
If an error message with
"
message disappears. A time function that has been set is
cleared. If the error message does not disappear, please
contact the after-sales service.
You can take remedial action yourself if the following error
message is displayed.
Error message Possible cause Remedy/information
A button was
"‹‚‚
depressed for
too long or is
covered up.
:
Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be carried
out by one of our trained after-sales engineers.
Hob
Problem
Possible cause
The appli-
The circuit
ance does
breaker is defec-
not work.
tive.
* Do not place hot pans close to or on the control panel.
Look in the fuse box and
check that the circuit
breaker is in working order.
Check whether the kitchen
light or other kitchen appli-
ances are working.
Reset the clock.
Turn the control knobs back
and forth several times.
appears, press the
0
button. The
Press all buttons individu-
ally. Check whether any but-
tons are jammed, covered
up or soiled.
Remedy/information
Look in the fuse box and
check that the circuit breaker
is in working order.
Put the cover back in place and press on it.
3.
Attach the oven door.
4.
Do not use the oven again until the panels have been
correctly installed.
Problem
Possible cause
Power cut
is flashing The control panel
"
is damp or an
object is resting
on it.
Electronic fault.
"§
+ num-
ber
š
+ number
+ number
¡
or
"‹
/
"Š
The electronics
"ƒ
have overheated
and have
switched off the
corresponding
hotplate.
The electronics
"...
have overheated
and have
switched off the
corresponding
hotplate.
The hotplate was
"‰
in operation for
too long and has
switched itself off.
Incorrect connec-
—‚
tion
The hotplate has
—ƒ
/
—„
overheated and
switched itself off
to protect the hob
* Do not place hot pans close to or on the control panel.
Replacing the bulb in the oven ceiling light
If the bulb in the oven light fails, it must be replaced. Heat-
resistant, 40 watt spare bulbs can be obtained from our after-
sales service or a specialist retailer. Only use these bulbs.
:
Risk of electric shock!
Switch off the circuit breaker in the fuse box.
Place a tea towel in the oven when it is cold to prevent
1.
damage.
Remedy/information
Check whether the kitchen
light or other kitchen appli-
ances are working.
Dry the control panel or
remove the object.
Switch the appliance off and
back on again after about
30 seconds using either the
household fuse or the circuit
breaker in the fuse box. Con-
tact the after-sales service if
this appears in the display
again.
Wait until the electronics
have cooled down suffi-
ciently. Touch any symbol
relating to this hotplate. The
display goes out.*
Wait until the electronics
have cooled down suffi-
ciently. Touch any symbol on
the control panel.*
You can switch the hotplate
back on again immediately.
The appliance must be con-
nected by a licensed expert.
Wait until the hotplate has
cooled down.
21
Advertisement
Table of Contents
