Traxxas RUSTER 4x4 BRUSHLESS Owner's Manual page 17

Higher Speeds Require Greater Distance
The faster you drive your model, the more quickly it will near the
limit of radio range. At top speeds, models can cover anywhere
between 25 to 100 feet every second! It's a thrill, but use caution to
keep your model in range. If you want to see your model achieve its
maximum speed, it is best to position yourself in the middle of the
truck's running area, not the far end, so you drive the truck towards
and past your position. In addition to maximizing the radio's range,
this technique will keep your model closer to you, making it easier
to see and control.
Your model's radio system is designed to operate reliably up to the
approximate distance that it is no longer easy or comfortable to see
and control the model. Most drivers will struggle to see and drive
their model at distances farther than a football field (300+ feet). At
greater distances, you could lose sight of your model and you may
also exceed the radio system's operating range which will cause
the Failsafe system to activate. For best visibility and control of your
model keep your model within 200 feet, regardless of the maximum
range available.
No matter how fast or far you drive your model, always leave
adequate space between you, the model, and others. Never drive
directly toward yourself or others.
TRANSMITTER LED CODES
LED Color / Pattern Name
Solid green Normal Driving
Mode
Slow red Binding
(0.5 sec on / 0.5 sec off )
Flashing medium red Low Battery
(0.25 sec on / 0.25 sec off ) Alarm
Flashing fast red Link Failure /
(0.125 sec on / 0.125 sec Error
off )
TQ 2.4GHz Binding Instructions
For proper operation, the transmitter and receiver must be
electronically 'bound.' This has been done for you at the factory.
Should you ever need to re-bind the system or bind to an additional
transmitter or receiver, follow these instructions. Note: the receiver
must be connected to a 4.8-6.0v (nominal) power source for binding
and the transmitter and receiver must be within 5 feet of each other.
1. Press and hold the SET button on the transmitter.
2. Turn on the transmitter and release the SET button. The status
LED will flash red slowly, indicating that the transmitter is in bind
mode.
3. Press and hold the LINK button on the receiver.
4. Turn on the speed control by pressing the EZ-Set button and
release the LINK button.
5. When the LEDs on both the transmitter and the receiver turn solid
green, the system is bound and ready for use. Confirm that the
steering and throttle operate properly before driving your model.
RECEIVER LED CODES
Notes LED Color / Pattern
See page 15 for information Solid green
on how to use the transmitter
controls.
See this page for more information Slow red
on binding. (0.5 sec on / 0.5 sec off )
Put new batteries in the Flashing fast red
transmitter. See page 13 for (0.125 sec on / 0.125 sec
more information. off )
Transmitter and receiver are no
longer bound. Turn the system
off and then back on to resume
normal operation. Find source of
the link failure (i.e., out of range,
low batteries, damaged antenna).
TRAXXAS TQ 2.4GHz RADIO SYSTEM
Name Notes
Normal Driving See page 15 for information
Mode on how to use your transmitter
controls.
Binding See this page for more information
on binding.
Failsafe / Low- Consistent low voltage in the
Voltage Detect receiver triggers Failsafe so
that there is enough power to
center the throttle servo before it
completely loses power.
Failsafe
Your Traxxas radio system
is equipped with a built-in
Failsafe function that returns
the throttle to its last saved
neutral position in the event
of a signal loss. The LED
on the transmitter and the
receiver will rapidly flash red
when the Failsafe mode is
activated. If Failsafe activates
while you are operating your
model, determine the reason
for signal loss and resolve the
problem before operating
your model again.
RUSTLER 4X4 • 17