Traxxas RUSTER 4x4 BRUSHLESS Owner's Manual page 10

Applying the Decals
The main decals for your
model have been applied at
the factory. Additional decals
have been printed on self-
adhesive clear mylar and are
die-cut for easy removal. Use
a hobby knife to lift the corner
of a decal and lift it from the
backing.
To apply the decals, place one
end down, hold the other end
up, and gradually smooth the
decal down with your finger
as you go. This will prevent air
bubbles. Placing both ends
of the decal down and then
trying to smooth it out will
result in air pockets. Look
at the photos on the box for
typical decal placement.
8 8
10 • RUSTLER 4X4
TRAXXAS TQ 2.4GHz RADIO SYSTEM
INTRODUCTION
Your model includes the TQ 2.4GHz transmitter. When powered
on, the TQ 2.4GHz will automatically locate and lock onto an
available frequency, allowing multiple models to be raced together
without frequency conflicts. Just switch on and drive! The included
TQ 2.4GHz radio system has been programmed for your model
at the factory and does not require adjustment, but it does have
settings you may need to access to maintain proper operation of
your model. The detailed instructions (page 15) included in this
manual will help you understand and operate the functions of the
new TQ 2.4GHz radio system. For additional information and how-
to videos, visit Traxxas.com.
RADIO AND POWER SYSTEM TERMINOLOGY
Please take a moment to familiarize yourself with these radio and
power system terms. They will be used throughout this manual.
BEC (Battery Eliminator Circuit) - The BEC can either be in the
receiver or in the ESC. This circuit allows the receiver and servos
to be powered by the main battery pack in an electric model. This
eliminates the need to carry a separate pack of 4 AA batteries to
power the radio equipment.
Brushless Motor - A D/C brushless motor replaces the brushed motor's
traditional commutator and brush arrangement with intelligent
electronics that energize the electromagnetic windings in sequence
to provide rotation. Opposite of a brushed motor, the brushless
motor has its windings (coils) on the perimeter of the motor can and
the magnets are mounted to the spinning rotor shaft.
Cogging - Cogging is a condition sometimes associated with
brushless motors. Typically, it is a slight stutter noticed when
accelerating from a stop. It happens for a very short period as the
signals from the electronic speed control and the motor synch
with each other. The BL-2s electronic speed control is optimized
to virtually eliminate cogging.
Current - Current is a measure of power flow through the
electronics, usually measured in amps. If you think of a wire as a
garden hose, current is a measure of how much water is flowing
through the hose.
ESC (Electronic Speed Control) - An electronic speed control is the
electronic motor control inside the model. The BL-2s electronic
speed control uses advanced circuitry to provide precise, digital
proportional throttle control. Electronic speed controls use
power more efficiently than mechanical speed controls so that
the batteries run longer. An electronic speed control also has
circuitry that prevents loss of steering and throttle control as the
batteries lose their charge.
Frequency band - The radio frequency used by the transmitter to
send signals to your model. This model operates on the 2.4GHz
direct-sequence spread spectrum.
kV Rating - Brushless motors are often rated by their kV number.
The kV rating equals no-load motor rpm with 1 volt applied. The
kV increases as the number of wire turns in the motor decreases.
As the kV increases, the current draw through the electronics also
increases. The BL-2s 3300 motor is a 3300 kV motor optimized for
the best speed and efficiency in lightweight 1/10 scale models.
LiPo - Abbreviation for Lithium Polymer. Rechargeable LiPo
battery packs are known for their special chemistry, which
allows extremely high energy density and current handling in a
compact size. These are high performance batteries that require
special care and handling. LiPo battery packs are for advanced
users only.
mAh – Abbreviation for milliamp hour, a measure of the capacity of
the battery pack. The higher the number, the longer the battery
will last between recharges.
Neutral position - The standing position that the servos seek when
the transmitter controls are at the neutral setting.
NiCad - Abbreviation for nickel-cadmium. The original rechargeable
hobby pack, NiCad batteries have very high current handling,
high capacity, and can last up to 1000 charging cycles. Good
charging procedures are required to reduce the possibility of
developing a "memory" effect and shortened run times.
NiMH - Abbreviation for nickel-metal hydride. Rechargeable NiMH
batteries offer high current handling and much greater resistance
to the "memory" effect. NiMH batteries generally allow higher
capacity than NiCad batteries. They can last up to 500 charge
cycles. A peak charger designed for NiMH batteries is required for
optimal performance.
Receiver - The radio unit inside your model that receives signals
from the transmitter and relays them to the servos.