1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower Accessories
  5. 147-6346
  6. Installation instructions manual

Toro 147-6346 Installation Instructions Manual

Z master 2000 or 4000 series riding mower universal mount kit
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
Universal Mount Kit
Z Master
Model No. 147-6346
Important:
If the Bagger Kit is installed on the machine, you cannot install the Universal Mount Kit.
Safety
Safety and Instructional
Decals
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.
136-1672
1. Warning—do not step; no riders.
136-1680
1. Maximum weight is 11 kg (25 lb)
© 2023—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
2000 or 4000 Series Riding Mower
decal136-1672
decal136-1680
Register at www.Toro.com.
Form No. 3462-522 Rev A
Installation Instructions
*3462-522*
Original Instructions (EN)
Printed in the USA
All Rights Reserved

Advertisement

Table of Contents
loading

Related Manuals for Toro 147-6346

Summary of Contents for Toro 147-6346

  • Page 1 Form No. 3462-522 Rev A Universal Mount Kit Z Master ® 2000 or 4000 Series Riding Mower Model No. 147-6346 Installation Instructions Important: If the Bagger Kit is installed on the machine, you cannot install the Universal Mount Kit. Safety...

  • Page 2: Installation

    Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Qty. – No parts required Prepare the machine. Main bracket Top bracket Bottom bracket plate Top bracket plate Carriage bolt (5/16 x 7/8 inch) Assemble the kit.

  • Page 3: Assembling The Kit

    Assembling the Kit Assemble the kit as shown in Figure 1. Do not overtighten the bolt (1/4 x 4-1/4 inches) and nut (1/4 inch); the hinge bracket must pivot freely. Important: Secure the bottom bracket plate to the machine before installing the hinge bracket. g439098 Figure 1 1.

  • Page 4: Mounting Locations

    Mounting the Kit to the Machine Mounting Locations You can mount this kit in 2 locations on the machine (Figure 2). Refer to the following procedures to mount the kit in the desired location. g437410 Figure 2 1. Side of the engine guard...
  • Page 5 Mounting the Kit to the Side of the Engine Guard WARNING The engine can become very hot. Touching a hot engine can cause severe burns. Allow the engine to cool completely before service or making repairs around the engine area. Secure the mount assembly to the side rear guard using 1 carriage bolt (1/4 x 1 inch) and 1 nut (1/4 inch) as shown in Figure 3...
  • Page 6 Important: If you are mounting to the right side on a Z Master 4000, remove the existing bolt that secures the expansion tank to the frame. Discard this bolt and use the kit hardware to secure the bracket to the frame. g437355 Figure 4 Mounting the kit to the right side of the engine guard...

  • Page 7: Operation

    1. Add a front-weight kit when 2 accessory-mount kits are installed at these positions. Operation Mounting Attachments Use only Toro-approved attachments and accessories. The maximum capacity is 11.3 kg (25 lb). Use the top bracket and hinge bracket for mounting attachments or accessories; secure them using the holes in the mounting brackets.
  • Page 8 Securing the Hinge Bracket Raise the hinge bracket. Loosen the knob and lower the top bracket, inserting the tab into the notch in the hinge bracket (Figure Tighten the knob. g037423 Figure 7 1. Tab in top bracket 2. Notch in hinge bracket...

Table of Contents