Table of Contents
Advertisement
HHP
■
|
wmi
h
_
Sllliilllv
Mi
■II
■
g|?§/,
iiSi
Do not cover the air inlet port or the air outlet port.
Do not mix old and new batteries.
• Doing so may cause the projector to overheat, which
9
If the batteries are inserted incorrectly, they may
can cause fire or damage to the projector.
explode or leak, and fire, injury or contamination of
• Do not P|ace the projector in narrow, badly ventilated
the battery compartment and surrounding area may
places such as closets or bookshelves.
result.
• Do not place the projector on cloth or papers, as
these materials could be drawn into the air inlet port.
Do not put your weight on this projector.
• You could fall or the projector could break, and injury
Do not set up the projector in humid or dusty places
may result.
or in places where the projector may come into
• Be especially careful not to let young children stand
contact with oily smoke or steam.
or sit on the projector.
• Using the projector under such conditions may result
in fire, electric shocks or plastic deterioration. The
If not using the projector for an extended period of
plastic deterioration may cause the falling down of
time, disconnect the mains plug from the mains
the projector which is mounted in the ceiling.
socket.
• If dust builds up on the mains plug, the resulting
When disconnecting the mains lead, hold the plug,
humidity may damage the insulation, which could
not the lead.
result in fire.
• If the mains lead itself is pulled, the lead will become
damaged, and fire, short-circuits or serious electric
Disconnect the mains plug from the mains socket
shocks may result.
as a safety precaution before carrying out any
cleaning.
Always disconnect all cables before moving the
• Electric shocks can result if this is not done
projector.
• Moving the projector with cables still attached can
If the lamp has broken, ventilate the room
damage the cables, which could cause fire or electric
immediately. Do not touch or bring your face close
shocks to occur.
to the broken pieces.
• Failure to observe this may cause the user to absorb
Do not place any heavy objects on top of the
the gas which was released when the lamp broke
projector.
and which contains nearly the same amount of
• Failure to observe this may cause the projector to
mercury as fluorescent lamps, and the broken pieces
become unbalanced and fall, which could result in
may cause injury.
damage or injury.
• if you believe that you have absorbed the gas or that
_
^
_ .
the gas has got into your eyes or mouth, seek
Do not short-circuit, heat or disassemble the
medical advice immediately
batteries or place them into water or fire.
• Ask your dea|er about the replacement of the lamp
• Failure to observe this may cause the batteries to
unit and check the inside of the projector,
overheat, leak, explode or catch fire, and burns or
other injury may result.
Ask an Authorised Service Centre to clean inside
....
.
the projector at least once a year.
When inserting the batteries, make sure the
. If dust is left to build up inside the projector without
po anhes (+ and -) are correct.
being c|eaned out, it can result in fire or problems
• If the batteries are inserted incorrectly, they may
with operation
explode or leak, and fire, injury or contamination of
• |t is a good idea to clean the inside of the projector
the battery compartment and surrounding area may
bef0re the season for humid weather arrives. Ask
resu 1
your nearest Authorised Service Centre to clean the
Use only the specified batteries
projector when required. Please discuss with the
• If incorrect batter.es are used, the, may explode or
Authorised Sendee Centre regard,ng cleaning costs
leak, and fire, injury or contamination of the battery
compartment and surrounding area may result.
We are constantly making efforts to preserve and maintain a clean environment. Please take non repairable
units back to your dealer or a recycling company.
8 - English
Make sure the following accessories are provided with your projector._
Remote control
(EUR7914Z40 x 1)
AA batteries for
Remote control
(x 2)
m f'
i t
'1
B1E3C3
223 jlENSj
jASPEcj FtuCtfl
Mains lead
for continental Europe (K2CM3FZ00003 x 1)
Mains lead
for UK (K2CT3FZ00003 x 1)
Cautions when transporting
Do not subject the projector to excessive vibration
or shocks.
• The projector lens need to be handled with care.
• Cover the lens with the lens cover when transporting
the projector.
When transporting the projector, hold the body at
the bottom securely.
® Do not hold the adjuster legs or the top cover to
move the projector, as this may damage the
projector.
Cautions when installing
Avoid setting up in places which are subject to
vibration or shocks.
• The internal parts can be damaged, which may
cause malfunctions or accidents.
Avoid setting up in places which are subject to
sudden temperature changes, such as near an air
conditioner or lighting equipment.
• The life of the lamp may be shortened or the
projector may be turned off. See "TEMP indicator" on
page 40.
Do not set up the projector near high-voltage power
lines or near motors.
• The projector may be subject to electromagnetic
interference.
If installing the projector to the ceiling, ask a
qualified technician to carry out all installation
work,
• You will need to purchase the separate installation kit
(Model No. ET-PKX100, ET-PKE1000S).
Furthermore, all installation work is better to be
carried out by a qualified technician.
If using this projector at high elevations
(above 1 400 m), set the ALTITUDE to HIGH. See
"ALTITUDE" on page 39.
• Failure to observe this may result in malfunctions or
the life of the lamp or the other components may be
shortened.
English
-
9
Advertisement
Table of Contents
