Maintenance & Service; Noise / Vibration - Skil SW1E3475CA Original Instructions Manual

blade into the workpiece
- after the blade has penetrated through the workpiece
continue sawing along the marked cutting line
! do not make plunge cuts in metal materials
• Use the appropriate saw blades u
• When cutting metals, lubricate saw blade regularly with
oil
Splinter-free cutting
•
- cover cutting-line with several layers of wide tape
before cutting
- always face the good side of the workpiece down
• For more information see www.skil.com
MAINTENANCE / SERVICE
• This tool is not intended for professional use
Always keep tool clean (especially ventilation slots E 2)
•
! remove battery from tool before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
• Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT
• Do not dispose of electric tools, batteries, accessories
and packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit

NOISE / VIBRATION

• Measured in accordance with EN 62841 the sound
pressure level of this tool is
power level 98 dB(A) (uncertainty K =
vibration Þ (triax vector sum; uncertainty K = 1.5 m/s²)
cutting board 10.58 m/s²
✱
cutting wooden beams 8.46
✱
• The vibration emission level has been measured in
accordance with a standardised test given in EN 62841;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
87 dB(A) and the sound
3 dB), and the
m/s²
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
b
Scie sabre sans fil et
sans brosse
INTRODUCTION
• Cet outil est destiné à la coupe du bois, du plastique,
du métal et des matériaux de construction ainsi qu'à
l'élagage et à l'ébranchage des arbres.
• Cet outil n'est pas conçu pour un usage professionnel.
• Lisez et conservez ce mode d'emploi.3
DONNÉES TECHNIQUES 1
PIÈCES DE L'OUTIL 2
A Lame
B Semelle pivotante
C Serrage de lame
D Poignée cylindrique
E Fentes de ventilation
F Bouton de verrouillage
G Interrupteur de marche/arrêt et réglage de vitesse
H Poignée
9. J Bouton de l'indicateur de niveau de batterie __
K Deux lampes LED
SÉCURITÉ
CONSIGNES DE SÉCURITÉ GÉNÉRALES POUR L'OUTIL
ÉLECTRIQUE
AVERTISSEMENT Lisez toutes les consignes
-
de sécurité, les instructions, les illustrations et les
spécifications de sécurité fournies avec cet outil
électrique. Le non-respect des consignes figurant ci-
dessous peut provoquer un choc électrique, un incendie et/
ou des blessures graves.
Conservez tous les avertissements et instructions pour
pouvoir vous y référer ultérieurement.
Le terme « outil électrique » utilisé dans les consignes de
sécurité désigne votre outil électrique fonctionnant sur
secteur (filaire) ou sur batterie (sans fil).
1) SÉCURITÉ DE L'AIRE DE TRAVAIL
a) Maintenez l'aire de travail propre et bien éclairée.
Les endroits sombres ou désordonnés augmentent les
risques d'accident.
b) N'utilisez pas les outils électriques dans des
atmosphères explosives, par exemple en présence
de liquides, gaz ou poussières inflammables. Les
outils électriques génèrent des étincelles pouvant
enflammer les poussières et les vapeurs.
11
3475