Important Installation Information - Thermador PRG364GDH Installation Manual

Important Installation Information

GAS Type Verification
Verify the type of gas supplied to the location. Ensure that
the appliance is connected to the type of gas for which it is
certified. Ranges are certified for use with only natural gas
or propane (LP) gas. Make certain the range matches the
gas type available; these ranges are NOT convertible
between gas types.
:
WARNING
To avoid possible burn or fire hazard, a
backguard designed specifically for this range
must be installed whenever the range is used.
Refer to the "Chart C: Backguard Kit Model Numbers"
on page 14, for the correct backguard models that are
designed for this range. After selecting the correct
backguard, the range must be installed properly, using
the minimum clearances to combustible surfaces
specified in the Cabinet Preparation instructions on
page 4.
Important:
• A backguard must be utilized when there is less than a
12" horizontal clearance between combustible
materials and the back edge of the range. The
Thermador Low Back backguard must be ordered
separately and installed at the rear of the range. For
island installations and other installations with more
than 12" clearance, an optional stainless steel Island
Trim is available to cover the backguard mounting
flanges.
• Verify that the appliance is correct for the type of gas
being provided. Refer to Step 5 on page 12 before
proceeding with the installation.
CAUTION:
To eliminate risk of burns or fire caused by
reaching over heated surface units, cabinet
storage located above the surface units should
be avoided.
Gas Supply:
Natural Gas — 6 inch water column. (14.9 mb) min., 14
inch (34.9 mb) maximum
Propane Gas — 11 inch water column. (27.4 mb) min., 14
inch (34.9 mb) maximum
English 2
Electric Power Supply:
30" Model:
4 Burners — 120 VAC, 60 Hz., 1Ph., 10 Amp circuit.
36" Models:
6 Burners — 120 VAC, 60 Hz., 1Ph., 10 Amp circuit
4 Burners with Griddle — 120 VAC, 60 Hz., 1Ph., 20 Amp
circuit.
CAUTION:
When connecting the unit to propane gas, make
certain the propane gas tank is equipped with its
own high-pressure regulator in addition to the
pressure regulator supplied with the range.The
maximum gas pressure to this appliance
must not exceed 14.0 inches water column
(34.9 mb) from the propane gas tank to the
pressure regulator.
CAUTION:
This unit is designed as a cooking appliance.
Based on safety considerations, never use it for
warming or heating a room.
This appliance has been tested in accordance with ANSI
Z21.1, Standard for Household Cooking Appliances (USA)
and in accordance with CAN 1.1-M81 Domestic Gas
Ranges (Canadian). It is strongly recommended that this
appliance be installed in conjunction with a suitable
overhead vent hood. (See Step 1 for Ventilation
Requirements.) Due to the high heat capability of this unit,
particular attention should be paid to the hood and duct
work installation to assure it meets local building codes.
This appliance complies with one or more of the following
standards:
• UL 858, Standard for the Safety of Household Electric
Ranges
• UL 923, Standard for the Safety of Microwave Cooking
Appliances
• UL 507, Standard for the Safety of Electric Fans
• ANSI Z21.1, American National Standard for
Household Cooking Gas Appliances
• CAN/CSA-C22.2 No. 113-M1984 Fans and Ventilators
• CAN/CSA-C22.2 No. 61-M89 Household Cooking
Ranges
Check local building codes for the proper method of
appliance installation. Local codes vary. Installation,
electrical connections and grounding must comply with all
applicable codes. In the absence of local codes the