Table of Contents
Advertisement
®
MAGNUM PRO
CURVE HDE 250, 350, 450 & 550
CONNECTOR KIT INSTALLATION TO GUN CABLE
The Magnum Pro curve HDE 250, 350, 450 & 550 guns are
shipped as generic assemblies and must be assembled to a
Magnum Connector Kit before they can be connected to a wire
feeder. See Connector Kit Table on page A-1 for appropriate
connector kit.
K466-1 and K466-8 Installation (for Lincoln Feeders)
a) Remove brass cable connector and insulation tube (see Figure
1) from the kit. Slide the insulation tube onto the connector
from the threaded end and screw it onto the feeder end of the
gun cable. Tighten the connection.
b) Remove the molded gas plug fitting on the side of the feeder
end handle and replace it with the barbed brass fitting
provided in the kit.
c) Attach the round connector of the gun control cable provided
to the trigger connector on the front of the Lincoln feeder.
NOTE:
Both the plug and socket are keyed and must be
properly oriented.
d) Place one tubing clamp onto each end of the flexible tubing
provided, approximately 2" (51 mm) in from each end. Slide
one end of the tubing onto the barbed connector on the
feeder end cable handle (step b) and move the clamp down
near the end of the tube to assure a good gas seal.
K466-2 Installation (For Tweco Adapted Feeders)
a) Remove brass cable connector (see Figure 1) from the K466-2
kit and screw it onto the feeder end of the gun cable. Tighten
the connection.
b) Check that the molded gas plug fitting is sealing the gas
fitting hole in the side of the feeder end handle.
K466-3 Installation (For Miller feeders)
a) Remove brass cable connector (see Figure 1) from the K466-3
kit and screw it on to the feeder end of the gun cable.
Tighten the connection.
b) Check that the molded gas plug fitting is sealing the gas
fitting hole in the side of the feeder end handle.
c) Attach the round connector of the gun control cable provided
to the trigger connector on the front of the Miller feeder.
K466-6 and K466-10 Installation (Wirematic and
Lincoln 10 Series Feeders)
a)
Remove brass cable connector (see Figure 1) from the
connector kit and screw it onto the feeder end of the gun
cable. Tighten the connection with the wrench provided.
b)
Check that the molded gas plug fitting is sealing the gas
fitting hole in the side of the feeder end handle.
c)
Attach the gun control cable provided to the trigger connector
on the front of the wire feeder.
K613-1 Installation
a) Remove brass cable connector and insulation tube from the
K613-1 Kit. Slide the insulation tube onto the connector from
threaded end and screw it onto the feeder end of the gun
cable. Tighten the connection.
b) Remove the molded gas plug fitting on the side of the feeder
end handle and replace it with the barbed brass fitting
provided in the kit.
c) Attach the round connector of the gun control cable provided
to the trigger connector on the front of the Lincoln Feeder.
Note: Both the plug and socket are keyed and must be properly
oriented.
d) Place one tubing clamp onto each end of the flexible tubing
provided, approximately 2" (51mm) in from each end. Slide
one end of the tubing onto the barbed connector on the
feeder end cable handle (step b) and move the clamp down
near the end of the tube to assure a good gas seal.
K613-3 Installation
a) Remove brass cable connector from the K613-3 kit and screw
it on to the feeder end of the gun cable. Tighten the
connection.
b) Check that the molded gas plug fitting is sealing the gas
fitting hole in the side of the feeder end handle.
c) Attach the round connector of the gun control cable provided
to the trigger connector on the front of the Miller feeder.
K613-2, K613-7 Installation
a) Remove brass cable connector from the kit and screw it onto
the feeder end of the gun tube, Tighten the connection with
wrench provided.
b) For K613-7, attach the round connector of the gun control
cable provided to the trigger connector on the front of the
Lincoln feeder.
K613-6 Installation
a) Remove brass connector and insulation tube from the kit.Slide
the insulation tube onto the connector from the threaded end
and screw it onto the feeder end of the gun cable.tighten the
connection with the wrench provided.
b) Attach the round connector of the gun control cable provided
to the trigger connector on the front of the Lincoln Feeder.
A-5
INSTALLATION
Advertisement
Table of Contents
