Table of Contents
Advertisement
Before using for the first time
In this section you will find out which steps are required before
using the appliance for the first time:
setting the clock
■
changing the water hardness range if required
■
before first use
■
cleaning the accessories before use
■
Your appliance was thoroughly factory tested for proper
operation. As a result, there may already be a small amount of
condensation in the appliance.
Setting the clock
After the power has been connected, the
:
light up in the display.
‹‹
‹‹
Set the current time using the rotary selector.
1.
Press the
button.
0
2.
The current time is applied.
Setting the water hardness range
Descale your appliance regularly. This is the only way to
prevent damage.
Your appliance automatically displays when it needs descaling.
It has been preset to the "medium" water hardness range.
Change the value if your water is softer or harder.
You can enquire about the water hardness with your water
supplier.
If your water is very hard, we recommend that you use softened
water.
You can only dispense with descaling completely if you
exclusively use softened water. If this is the case, change the
water hardness to "softened".
You can change the water hardness range in the basic settings
when the appliance is switched off.
If required, press the
#
1.
Press and hold the
button until
0
2.
display.
Operating the appliance
In this section, you can read about
how to fill the water tank
■
how to switch the appliance on and off
■
what to note after each use
■
how to change the clock time
■
Filling the water tank
Press the
w
symbol to open the appliance door. You can see
the water tank on the right.
Caution!
Use of unsuitable liquids may damage the appliance
Only use fresh tap water, softened water or uncarbonated
■
mineral water.
If your tap water is very hard, we recommend that you use
■
softened water.
Do not use distilled water, highly chlorinated tap water
■
(> 40 mg/l) or other liquids.
You can obtain information about your tap water from your
water supplier.
8
symbol and
À0
button to switch off the appliance.
appears in the
™‚ ‚
Press the
0
button repeatedly until
3.
hardness range "medium").
Turn the rotary selector to change the water hardness range.
4.
Possible values:
softened
™† ‹
soft
™† ‚
medium
™† ƒ
hard
™† „
very hard
™† ...
Press and hold the
0
button to exit basic settings.
5.
The change is saved.
First use
Before first use, heat the empty appliance for 20 minutes at
100 °C. Do not open the appliance door during this time. The
appliance is automatically calibrated (see section: Automatic
calibration).
Press the
button to switch on the appliance.
#
1.
Fill the water tank and insert it (see section: Filling the
2.
water tank).
Press the
J
button.
3.
The appliance heats up to 100 °C. The cooking time
(20 minutes) does not start to count down until the set
temperature has been reached. Do not open the appliance
door during this time.
The cooking operation ends automatically and an audible
signal sounds.
Press the
button to switch off the appliance.
#
4.
Leave the appliance door ajar until the appliance has cooled
down.
Cleaning the accessories before use
Using soapy water and a soft cloth, clean the accessories
thoroughly before first use.
Fill the water tank before each use:
Open the appliance door and remove the water tank (fig. A).
1.
Fill the water tank with cold water (fig. B).
2.
MIN
Amount of water required for approx. 30 minutes
steaming at 100 °C
MAX
Amount of water required for approx. 2 hours
steaming at 100 °C
™† ƒ
appears (water
-
I
II
II
IV
Advertisement
Table of Contents
