Miele PDR 918 HP Operating And Installation Instructions
Commercial heat pump dryers
Hide thumbs
Also See for PDR 918 HP:
- Quick start manual (160 pages) ,
- Operating and installation instructions (60 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Miele PDR 918 HP
Summary of Contents for Miele PDR 918 HP
- Page 1 Operating and installation Instructions Commercial heat pump dryers PDR 914/918/922 HP To avoid the risk of accidents or damage to the en-AU, NZ appliance, it is essential to read these instructions before it is installed and used for the first time. M.-Nr. 11 864 930...
-
Page 2: Table Of Contents
Contents Caring for the environment .................... Warning and Safety instructions ................... Correct application......................Preventing problems ......................Technical safety......................... Correct use........................11 Accessories ........................11 Operating the tumble dryer .................... 12 Control panel ........................12 Sensors and touch display with sensors................13 Main menu......................... - Page 3 Contents Timer ..........................26 Prerequisite for setting the timer ................... 26 Setting the timer......................26 Cleaning and care ......................27 Cleaning the fluff filter ....................... 27 Tumble dryer........................28 Heat exchanger ......................... 29 Problem solving guide ....................31 After sales service......................32 Contact in case of fault .....................
- Page 4 Additional fan ........................ 53 Pressure sensor ......................53 Peak load signal ......................53 Peak load prevention ....................53 COM module selection ....................54 Availability of Miele digital products................54 Wi-Fi / LAN........................54 Network time......................... 54 Remote.......................... 55 RemoteUpdate ......................55 Machine parameters......................
- Page 5 Contents Technical data........................57 Technical data ........................57...
-
Page 6: Caring For The Environment
Please dispose of it at your local community waste collection / recycling centre for electrical and electronic appliances. Consult with Miele if necessary. Please ensure that your old appliance presents no danger to children while being stored awaiting disposal. -
Page 7: Warning And Safety Instructions
“Installation”, as well as in the “Warning and Safety instructions”. Miele cannot be held liable for injury or damage caused by non-compliance with these instructions. Keep these operating instructions in a safe place and pass them on to any future owner. -
Page 8: Preventing Problems
The tumble dryer may only be operated with a peak- load device if this is connected to the tumble dryer via the Miele connector box and the relevant settings have been configured on the tumble dryer. There is a risk of the laundry self-igniting if the drying programme is cancelled before the cooling phase has finished. -
Page 9: Technical Safety
Unauthorised repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability. Repairs must only be carried out by a Miele authorised service technician, otherwise any subsequent damage will not be covered by the warranty. - Page 10 If the electrical connection cable is faulty, it must only be replaced by a Miele authorised service technician to protect the user from danger.
-
Page 11: Correct Use
If you order a plinth for this tumble dryer (available from Miele as an optional accessory), make sure it is the correct one. Miele cannot be held liable for damage caused by non-compliance with these... -
Page 12: Operating The Tumble Dryer
Operating the tumble dryer Control panel sensor For selecting the current user language. At the end of the programme, the language is automatically reset to the language set at the Supervisor level. sensor Takes you back one level in the menu. Touch display / sensor For starting the selected drying programme and cancelling a programme that has... -
Page 13: Sensors And Touch Display With Sensors
Operating the tumble dryer Sensors and touch display with sensors The sensors , and Start/Stop and the sensors in the display respond to fingertip contact. Every touch of the sensors is confirmed by a keypad tone. You can adjust the volume of the keypad tone or switch it off (see “Supervisor level”). -
Page 14: Setting Numerical Values
Operating the tumble dryer To scroll through the menu, place your finger on the touch display and move it left or right. The orange scroll bar in the bottom display area shows that there are further options to choose from. To select the required drying programme, touch the programme name with your finger. -
Page 15: Pull-Down Menu
Operating the tumble dryer The numerical keypad will be displayed. Time 12:00 To enter the numerical value, touch the numbers on the right-hand side and then confirm with OK. Pull-down menu The pull-down menu can be used to display information (e.g. about a drying programme). ... -
Page 16: Using For The First Time
Some settings can only be modified during the initial commissioning process. After that, they can only be changed by Miele Professional Service. These settings are also described in "Supervisor level". Switching on the tumble dryer Press the button. -
Page 17: Reference To Optional External Devices
Using for the first time Reference to optional external devices Before initial commissioning, connect the Connector box and/or slide a communication module into the slot on the back of the tumble dryer. For this purpose, the tumble dryer must be disconnected from the power supply. -
Page 18: Selecting Programme Packages
Payment system”. These settings can only be changed during the initial commissioning process. If you wish to change the settings later, please contact Miele. If you do not wish to set up a payment system, you can skip this step. -
Page 19: Completing The Initial Commissioning Process
Using for the first time Payment system 11:02 Skipping payment system set-up No payment Timed COM module system operation Programme Timed op. + control impul.counter No payment system Touch the sensor. Touch to confirm. The display will change to the next setting. Completing the initial commissioning process The commissioning process is complete when a programme lasting longer than 10 minutes has been carried out in full. - Page 20 Using for the first time Duration Touch the sensor. Place your finger on the number that you want to change and move your finger upwards or downwards. Duration 11:02 Reset Select a duration of 10 minutes. Touch to confirm.
-
Page 21: Drying
Drying 1. Notes on correct laundry care Washing Heavily soiled laundry must be washed particularly thoroughly. Use sufficient detergent and select a high wash temperature. If in doubt, wash the items several times. New, coloured items should be washed thoroughly and separately. Do not dry these garments together with light coloured garments. -
Page 22: Loading The Tumble Dryer
Drying 2. Loading the tumble dryer Loading laundry Textiles may be damaged. into the tumble Before loading, read chapter “1. Notes on correct laundry care” dryer first. Open the door. Load laundry into the tumble dryer. Risk of damage with laundry getting trapped. Laundry can be damaged by getting trapped when closing the door. -
Page 23: Selecting A Programme
Drying 3. Selecting a programme Press the button. Switching on the tumble dryer The welcome screen will light up. There are different ways to select a drying programme in the main menu. 11:02 Programmes Favourites Supervisor Help Touch the sensor. -
Page 24: Selecting Programme Settings
Drying With your finger, swipe to the left until you reach the required programme. Touch the required programme. The display will change to the standard menu for that drying programme. 4. Selecting programme settings Selecting the The preset drying level can be changed for many programmes. drying level Different drying levels are available depending on the programme. -
Page 25: Starting A Programme
Drying 5. Starting a programme Payment system If your machine is connected to a payment system, the amount of (optional) payment required will appear in the display. Money may be lost if the drum door is opened or the programme is cancelled. -
Page 26: At The End Of The Programme
Drying programmes can therefore vary or “jump”. The tumble dryer’s electronic module adapts during the ongoing drying programme. The displayed programme running time becomes more and more accurate. When using the programmes for the first time, the displayed time sometimes deviates significantly from the real time left. The difference between the estimated and achieved time becomes smaller if the corresponding programme is run more often. -
Page 27: Cleaning And Care
Cleaning and care Cleaning the fluff filter Risk of fire if the tumble dryer is operated without a fluff filter. If there is no fluff filter, the air channels, heating elements and ducting can become clogged during drying and may catch fire. The fluff filter must not be removed for cleaning. -
Page 28: Tumble Dryer
Clean the louvres using a brush or vacuum cleaner. Then re-cover the air intake vent. Miele Professional Service must check the interior of the tumble dryer and the impellers in the ventilation openings for fluff deposits once per year and clean the machine if necessary. -
Page 29: Heat Exchanger
Cleaning and care Heat exchanger While the heat pump is running, fluff, detergent residue and other components contained in the steam collect in the heat exchangers. Soiling of the heat exchangers reduces heat transfer to the air and minimises the efficiency of the system. The heat exchangers must therefore be checked and cleaned at regular intervals. - Page 30 ter der Wartungsklappe) erlaubt. Für den Trockner Verunreinigungen. Sie verhindern dadurch ein Ver- und die weiteren Teile ist eine Reinigung mit Was- stopfen des Ablaufes. ser nicht zulässig. Lebensgefahr durch elektri- Achten Sie darauf, dass die Lamellen sich nicht ver- schen Schlag! Cleaning and care biegen oder beschädigt werden.
-
Page 31: Problem Solving Guide
Problem solving guide Problem Possible cause and remedy Condensate is escaping The drain is dirty. from an unexpected Inspect the drain and remove any soiling if necessary. location. The drain can be accessed via the rear service panel in the floor area. -
Page 32: After Sales Service
After sales service Contact in case of fault In the event of any faults which you cannot remedy yourself, please contact Miele Professional Service. Contact information for Miele can be found at the end of this booklet. Please quote the model and serial number of your appliance when contacting Miele. This information can be found on the data plate. -
Page 33: Installation
*INSTALLATION* Installation Installation requirements The heat pump dryer must only be installed and commissioned by a Miele Professional Service technician or a Miele authorised technician. The heat pump dryer must be installed in accordance with all relevant local and national regulations and applicable standards. -
Page 34: Installing The Heat Pump
*INSTALLATION* Installation At the next installation site, the tumble dryer and the heat pump must be lifted from the transport pallet using suitable lifting gear. Installing the heat pump Before the heat pump dryer is used for the first time, the tumble dryer and heat pump must be connected to one another. - Page 35 *INSTALLATION* Installation Position the tumble dryer in front of the heat pump air openings. Align the tumble dryer and heat pump above the machine feet horizontally and parallel to one another. Tilt the heat pump backwards slightly and move the tumble dryer ...
-
Page 36: Installation
*INSTALLATION* Installation Tumble dryer Heat pump The clamping lug connects the heat pump to the tumble dryer. Once this step is complete, the tumble dryer should no longer be able to move away. Put the tumble dryer lid on top of the tumble dryer and clamp the ... - Page 37 Useful tip: Use a spirit level to ensure correct alignment. In Australia and New Zealand, all PDR 922 HP machines are installed on a mobile plinth with lockable castors. This mobile plinth assists during maintenance and repair work by Miele technicians. The height of the machine is 1500 mm with castors fitted.
-
Page 38: Electrical Connection
If more than one voltage is specified on the data plate, the tumble dryer can be converted for connection to the relevant input voltage. This conversion must be performed by the Miele Professional Service Department or by an authorised technician. During the conversion, the wiring instructions given on the wiring diagram must be followed. - Page 39 *INSTALLATION* Installation When in the off position, this all-pole isolation device ensures a 3 mm gap between all open contacts. These include circuit breakers, fuses and relays. If the mains supply cannot be permanently disconnected, the isolation device (including plug and socket) must be safeguarded against being switched on either unintentionally or without authorisation.
-
Page 40: Air Intake Vent
*INSTALLATION* Installation Air intake vent During tumble dryer operation, the installation site must constantly be supplied with sufficient cool, fresh air. If the ambient temperature frequently exceeds 45 °C, the cooling circuit in the heat pump must be connected to external air intake and outlet vent ducting to ensure that heat pump functionality is not impaired. -
Page 41: Optional Accessories
Miele cannot accept liability. XCI box The optional XCI box allows external hardware from Miele and other suppliers to be connected to the Miele Professional machine. External hardware includes, e.g. payment system, peak-load system, pressure sensor or an external vent flap. -
Page 42: Factory Default Settings For Network Configuration
Miele as optional accessories for individual target groups. The programming required for connecting a payment system must be carried out by Miele Professional Service or an authorised technician only. A separate electrical connection is... -
Page 43: Supervisor Level
Carefully enter a new code. You will need to inform Miele if you have forgotten your new code. Miele will have to reset the code. Make a note of your new code and store it in a safe place. -
Page 44: Set Languages
Supervisor level International 6 languages are available. The sensor is not active. Note the setting Set languages Language selection The sensor can be used to select a language. All languages are available (factory setting). You can change the order of the first 4 languages. These slots are allocated to the most commonly used languages. -
Page 45: Volume
Supervisor level Volume The volume for various signal tones can be changed. The volume can be changed for the following sounds: Finish tone The end tone signals the end of a drying programme. Keypad tone Welcome tone Fault alarm The fault tone signals an fault and can be switched off. The volume of the fault tone cannot be changed. -
Page 46: Machine" Off Status
Supervisor level On after 10 min. - Factory default setting: The display switches off after 10 minutes. On (30 min.) Not curr.prog. The display will remain on while the programme is running, but will go out 30 minutes after the end of the programme. Logo (30 min.) Not curr.prog. -
Page 47: Logo
Supervisor level Logo You can choose whether the “Miele Professional” logo or your own logo appears in the display. Controls Launderette Logo Launderette Logo int. time Launderette For the setting, the , or Logo ext. time option must be selected. -
Page 48: Programme Packages
Supervisor level Favourite programmes Under , you can set which 12 programmes to select/modify. The first three programmes can be selected directly. The remaining programmes are selected via another list. Launderette Logo ext. time 4 timed programmes* with different temperature levels are time-controlled via an external payment system. -
Page 49: Special Programmes
Supervisor level Special programmes You can put together 5 special residual moisture or time-controlled programs and assign your own program names. First, enter the programme name. Select the special programme you want to change. Save as menu opens. Use the letters and symbols below the line to enter the name. ... -
Page 50: Sort Programmes
Supervisor level Drum reversal – 0 – 500 seconds Pause – 100 – 300 seconds Sort programmes Programmes can be moved within the programme list and in the Favourites list. - Factory setting: Off - On Moving programmes/favourite programmes You can move/change the order of the programmes (programme menu – single selection list). -
Page 51: Further Cooling
Supervisor level Further cooling Before the end of the programme, the temperature of the dried laundry is monitored and the cooling phase at the end of the programme is extended if necessary. Changing this setting leads to increased energy consumption. - Factory setting: Off - On Cooling down temperature... -
Page 52: Service Interval
External applications External exhaust flap External hardware is connected via the Miele XCI box. The time delay between the external exhaust air flap's activation point and the switch-on time for the drum/fan motor is regulated. -
Page 53: Additional Fan
The tumble dryer may only be operated with a peak-load system if this system is connected to the tumble dryer via the Miele XCI Box. - Factory setting: No function... -
Page 54: Com Module Selection
An XKM module or RS232 module is inserted into the module slot. Availability of Miele digital products The ability of Miele digital products depends on the availability of the services in your country. The different services are not available in all countries. -
Page 55: Remote
Wi-Fi network. Miele’s RemoteUpdate function can only be used if the tumble dryer is connected to a Wi- Fi network and you have an account in the Miele Professional App. The tumble dryer must be registered in the app. -
Page 56: Payment System
Supervisor level Copyright and licences For the purpose of operating and controlling the machine, Miele uses proprietary or third- party software that is not covered by open source licensing terms. These items of software/software components are protected by copyright. The copyright powers of Miele and third parties must be respected. - Page 57 Technical data Technical data PDR 914 HP PDR 918 HP PDR 922 HP Height 1,400 mm 1,400 mm 1,400 mm Width 906 mm 906 mm 906 mm Depth 1,232 mm 1,415 mm 1,544 mm Depth with door open 1,852 mm 2,055 mm 2164 mm Net weight 156.354 kg 169.5 kg 180.2 kg...
- Page 58 Freemans Bay Auckland 1011 New Zealand Telephone: 0800 4 MIELE (0800 464 353) www.miele.com.au/professional professional.sales@miele.com.au Miele Global Headquarters: Miele & Cie. KG Carl-Miele-Straße 29, 33332 Gütersloh, Germany Alteration rights reserved / Publication date: 27.23 M.-Nr. 11 864 930 / 01 ...