1. Manuals
  2. Brands
  3. TRENDnet Manuals
  4. Security Camera
  5. 15-AH28B
  6. Quick installation manual

TRENDnet 15AH-28B Quick Installation Manual

Trendnet 15ah28b: installation guide
Hide thumbs Also See for 15AH-28B:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
Quick Installation Guide
15AH-28B

Advertisement

Table of Contents
loading

Related Manuals for TRENDnet 15AH-28B

Summary of Contents for TRENDnet 15AH-28B

  • Page 1 Quick Installation Guide 15AH-28B...

  • Page 2: Before You Start

    1. Before you start Installation Requirements The following items below are not included. Users must provide the items themselves. Make sure to have each item on hand before installation. Internet Camera Server (e.g. TV-IP100, TV-IP201, TV-IP301) Dry Wall or Wood surface Power Cord Knife or box cutter Wire Stripper...

  • Page 3: Hardware Installation

    2. Hardware Installation Note: Configure your Internet Camera Server to match your network settings before installing the device. 1. Lift up the latch and pull the roof upward. 2. Remove the metal bracket from the camera enclosure by unscrewing the four screws. Save these screws.
  • Page 4 4. Flip over the camera housing and remove the rubber stoppers and washers. 5. Remove the circuit board from the camera enclosure by unscrewing the two screws. Save these screws. You will need to use these screws later. 6. Take a power cord and cut it using a wire cutter.
  • Page 5 8. Remove the insulation with pliers. 9. Run the power cord through the rubber stopper. 10. Insert the power cord through the hole and securely screw in the rubber stopper. 11. Insert the wires of the power cord into the power receptacle. Make sure the green and white wires match up.
  • Page 6 12. Mount the Internet Camera Server inside the camera enclosure with the screws. Temporarily leave one hole unscrewed. This example shows a TRENDnet TV-IP100W. 13. Ground the green wire on the 15AH-28B. Then screw in the last hole. 14. Take the camera's power adapter...
  • Page 7 17. Run the power adapter and the RJ-45 Ethernet cable from the base to the top of the mounting arm. Make sure to leave one end of the RJ-45 Ethernet cable unterminated. 18. Insert the power adapter, RJ-45 Ethernet Cable through the rubber stopper screw it in securely.
  • Page 8 21. Reconnect the circuit board back to the camera enclosure using the two screws. 22. Connect the Ethernet cable and power adapter to the camera. 23. Close and secure the back panel. 24. Plug the power cord and the camera power adapter into an available power outlet.
  • Page 9 Mounting the Camera Housing 1. Place the mounting bracket against the wall and mark each of the four holes with a pencil. 2. Drill holes for the fastener plugs at each marked position. Make sure the drill bit matches the size of the provided white screw anchors.
  • Page 10 4. Use the bracket screws to mount the mounting bracket to the housing. 5. Align the Wall Mount bracket with the fasteners, and then use the provided wood screws to secure it. Your installation is now complete. English...

  • Page 11: Troubleshooting

    Once the Ethernet cable is run through the rubber stopper and the 15AH-28B, then terminate the Ethernet cable with an RJ-45 jack. If you still encounter problems or have any questions regarding the 15AH-28B, please contact TRENDnet's Technical Support Department.
  • Page 12 15AH-28B - 1 Year Warranty If a product does not operate as warranted above during the applicable warranty period, TRENDnet shall, at its option and expense, repair the defective product or part, deliver to customer an equivalent product or part to replace the defective item, or refund to customer the purchase price paid for the defective product.
  • Page 13 PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF TRENDnet'S PRODUCTS. TRENDnet SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY...
  • Page 14 Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation.

  • Page 15: Product Warranty Registration

    English/Espanol - 24/7 Francais/Deutsch - 11am-8pm, Monday - Friday MET Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.trendnet.com 20675 Manhattan Place Torrance, CA 90501 Copyright ©2007. All Rights Reserved. TRENDnet.

Table of Contents