Mitsubishi Electric MSZ-LN18VG2W-SC1 Service Manual page 21

8-5. Wi-Fi INTERFACE SETTING UP
This Wi-Fi interface communicates the status information and controls
the commands from the MELCloud by connecting to an indoor unit.
Wi-Fi interface
Wi-Fi interface introduction
No. Item
1 MODE switch It selects modes.
2 RESET switch It resets the system and ALL settings.
3 ERR LED (Orange) It shows the network error state.
4 NET LED (Green) It shows the network state.
5 MODE LED (Orange) It shows the Access point mode state.
6 UNIT LED (Green) It shows the indoor unit state.
MSZ-LN18VG2W- ,
E2 ER2
MSZ-LN18VG2V/B/R-
E2
MSZ-LN25VG2W/V/B/R- ,
E2
MSZ-LN35VG2W/V/B/R- ,
E2
MSZ-LN50VG2W/V/B/R- ,
E2
MSZ-LN60VG2W/V/B/R- ,
E2
MSZ-LN25VGW/V/B/R
MSZ-LN35VGW/V/B/R
MSZ-LN50VGW/V/B/R
MSZ-LN60VGW/V/B/R
MSZ-LN18VG2W/V/B/R- ,
E1
MSZ-LN25VG2W/V/B/R- ,
E1
MSZ-LN35VG2W/V/B/R- ,
E1
MSZ-LN50VG2W/V/B/R- ,
E1
MSZ-LN60VG2W/V/B/R- ,
E1
Wi-Fi INTERFACE
XXXXXXXX
MODEL
MAC : XXXXXXXXXXXX
ID : XXXXXXXXXX
SSID : XXXXXXXXXXXX
KEY : XXXXXXXXXXXX
VOLTAGE :
:
CURRENT
ERR
MITSUBISHI ELECTRIC CORPRATION
NET
MODE
UNIT
RESET MODE
WiFi.ASSY DWG No. >PP<
XXXXXXXXXXX
MADE IN CHINA XXXXXXXXXX
(1) MODE switch
• The MODE switch is used for selecting modes in configurations.
(2) RESET switch
• Hold down the RESET switch for 2 seconds to reboot the system.
• Hold down the RESET switch for 14 seconds to initialize the Wi-Fi interface to
the factory default.
NOTE:
When the Wi-Fi interface is reset to the factory default, ALL the configuration
information will be lost. Take great care in implementing this operation.
OBH766G
Wi-Fi interface
Description
, ,
ET2
ER2 EN2
, ,
ER2 EN2 ET2
, ,
ER2 EN2 ET2
,
ER2 ET2
ER1
, ,
ER1 ET1 ET1
, ,
ER1 ET1 ET1
, ,
ER1 ET1 ET1
,
ER1 ET1
ERR
NET
MODE
UNIT
RESET MODE
(1) Open the front panel and remove the Wi-Fi interface.
(2) Set up a connection between the Wi-Fi interface and the router.
Refer to the SETUP MANUAL and SETUP QUICK
REFERENCE GUIDE provided with the unit.
For SETUP MANUAL, please go to the website below.
http://www.mitsubishielectric.com/ldg/ibim/
(3) Put the Wi-Fi interface back and close the front panel
after the setup is completed.
(4) For MELCloud User Manual, please go to the website below.
https://www.melcloud.com/Support
NOTE:
• Ensure that the Router supports the WPA2-AES encryption setting before
starting the Wi-Fi interface setup.
• The End user should read and accept the terms and conditions of the Wi-Fi
service before using this Wi-Fi interface.
• To complete connection of this Wi-Fi interface to the Wi-Fi service, the Rout-
er may be required.
• This Wi-Fi interface will not commence transmission of any operational data
from the system until the End user registers and accepts the terms and con-
ditions of the Wi-Fi service.
• This Wi-Fi interface should not be installed and connected to any Mitsubishi
Electric system which is to provide application critical cooling or heating.
• At the time of relocation or disposal, reset the Wi-Fi interface to the factory
default.
Mitsubishi Electric's Wi-Fi interface is designed for communication to Mit-
subishi Electric's MELCloud Wi-Fi service.
Third party Wi-Fi interfaces cannot be connected to MELCloud.
Mitsubishi Electric is not responsible for any (i) under performance of a sys-
tem or any product; (ii) system or product fault; or (iii) loss or damage to any
system or product; which is caused by or arises from connection to and/or use
of any third party Wi-Fi interface or any third party Wi-Fi service with Mitsubishi
Electric equipment.
For the latest information regarding MELCloud from Mitsubishi Electric
Corporation, please visit www.MELCloud.com.
21