Table of Contents
Advertisement
6. Use the brush (C5) to remove any coffee residues left in the
infuser housing, visible through the infuser door;
7. After cleaning, replace the infuser by sliding it onto the in-
ternal support, then push the PUSH symbol fully in until it
clicks into place;
Please note:
If the infuser is difficult to insert, before insertion, adapt it to the
right size by pressing the two levers (fig. 27).
8. Once inserted, make sure the two coloured buttons have
snapped out;
9. Close the infuser door;
10. Put the water tank back.
14.10 Cleaning the milk container
Clean the milk container (D) each time you prepare milk as de-
scribed below:
1. Remove the lid (D2);
2. Remove the milk spout (D5) and intake tube (D4) (fig. 28);
3. Turn the froth adjustment dial (D1) anticlockwise to the
"INSERT" position (fig. 29) and pull off upwards;
4. Wash all the components thoroughly with hot water and
mild washing-up liquid. All components are dishwasher
safe, placing them in the top basket of the dishwasher.
Make sure there are no milk residues on the hollow and
groove under the dial (fig. 30). If necessary, scrape the
groove with a toothpick;
5. Rinse inside the froth adjustment dial seat with running
water (fig. 31);
6. Check that the intake tube and milk spout are not clogged
with milk residues;
7. Replace the dial (in correspondence to the word "INSERT"),
spout and milk intake tube;
8. Place the lid back on the milk container (D3).
14.11 Cleaning the hot water nozzle
Each time you prepare milk, clean the connection nozzle (A8)
with a sponge to remove milk residues from the gaskets (fig.
20).
15. DESCALING
Important!
•
Before use, read the instructions and the labelling on the
descaler pack.
•
You should use De'Longhi descaler only. Using unsuitable
descaler and/or performing descaling incorrectly may re-
sult in faults not covered by the manufacturer's guarantee.
Descale the machine when "Descale, ESC to cancel, OK to des-
cale (∼45 minutes)" appears on the display (B1). To descale im-
mediately, press OK (B3) and follow the instructions from point
6. To descale the appliance later, press ESC (B5). The
on the display reminds you that the appliance needs descaling.
To access the descaling menu:
1. Turn the appliance on and wait until it is ready for use;
2. Press
(B6) to enter the "Settings" menu;
3. Press the selection arrows (B2 and B4) until "Maintenance"
is displayed between the two lines. Press OK (B3);
4. Press OK to select "Descale";
5. Confirm? (∼45 minutes)". Press OK to confirm;
6. "Remove filter": extract the water tank (A17), remove the
water softener filter (C4) (if present) and empty the water
tank. Press OK;
7. "Pour descaler and water into tank": Pour the descaler into
the tank up to level A (corresponding to a 100 ml pack)
marked on the inner surface of the tank, then add water
(1 litre) up to level B (fig. 32) and put the water tank back.
Press OK;
8. "Empty drip tray": Remove, empty and replace the drip
tray (A15) and grounds container (A11). Press OK;
9. "Place 1.8L container empty under spouts": Place an empty
container with a minimum capacity of 1.8 litres under the hot
water spout (C6) and coffee spouts (A9) (fig. 33). Press OK;
water and coffee spouts. A series of rinses and pauses is
performed automatically to remove all the scale residues
inside the coffee machine;
After about 25 minutes, descaling stops;
11. "Rinse tank and fill with water": the appliance is now
ready to rinse with fresh water. Empty the container used
to collect the descaler solution. Extract the water tank,
empty, rinse under running water, fill with fresh water up
to the MAX level and put back in the appliance. Press OK;
12. "Place 1.8L container empty under spouts": place the con-
tainer used to collect the descaler solution empty under
the coffee spouts and hot water spout (fig. 33) and press
OK";
13. "Rinsing Confirm?": press OK;
18
Important! Danger
of burns
Hot water containing acid
flows out of the coffee spouts
and hot water spout. Take
care to avoid contact with
splashes of this solution.
10. "Descaling underway":
The descale programme
starts and the descaler liq-
33
uid comes out of the hot
symbol
Advertisement
Table of Contents
Troubleshooting
