Table of Contents
Advertisement
3. Press OK (B3) to confirm and select the required item with
the selection arrows. Then follow the instructions for each
setting.
•
Set temperature:
To modify the temperature of the water used to make the coffee,
proceed as follows:
4. Press OK (B3). The current value appears on the display
(B1) and the "New" value flashes;
5. Select the new value you want to set using the selection
arrows (B2 or B4);
6. When the required value (low, medium, high, maximum)
has been selected, press OK.
The display goes back to the previous screen.
•
Water hardness:
For instructions on identifying and setting water hardness, see
section "16. Setting water hardness".
•
Auto-off (standby):
Auto-off can be set so that the appliance goes off after 15 or 30
minutes, or 1, 2 or 3 hours
4. Press OK. The current value appears on the display (B1) and
the "New" value flashes;
5. Select the new value you want to set using the selection
arrows (B2 or B4);
6. When the required value (low, medium, high, maximum)
has been selected, press OK.
The display goes back to the previous screen.
•
Energy saving:
Use this function to enable or disable energy saving. When en-
abled, the function reduces energy consumption in compliance
with European regulations.
To disable or enable "Energy Saving", proceed as follows:
4. Press OK. The current state ("Enabled" or "Disabled") and
the operation to be performed ("Disable?" or "Enable?") is
displayed. Press OK to confirm;
5. Press OK to disable or enable the function.
The display goes back to the previous screen.
Please note!
•
when the function is enabled, the symbol "ECO" appears
on the display.
•
When in energy saving mode, a few seconds elapse before
the first coffee, cappuccino or milk-based coffee is deliv-
ered as the appliance must heat up again.
•
If the milk container (D) is inserted, "Energy Saving" can-
not be activated.
•
Beep:
Use this function to enable or disable the beep. Proceed as
follows:
4. Press OK. The current state ("Enabled" or "Disabled") and
the operation to be performed ("Disable?" or "Enable?") is
displayed. Press OK to confirm;
5. Press OK to disable or enable the function.
The display goes back to the previous screen.
•
Default beverages:
Use this function to reset the default values for all the beverag-
es, or the individual beverages programmed previously. Select
the beverage, then proceed as follows:
4. Select "All" to reset the aroma and quantity settings to the
default values, or select the required beverage, then press
OK;
5. "Reset?": to reset the default values, press OK.
6. "Reset complete": the appliance confirms the reset and
goes back to the previous screen.
To reset another beverage, repeat from point 4 or to exit, press
/ESC (B5).
•
Default values:
Use this function to reset all the appliance and beverage settings
(apart from the language which remains as selected the first
time the appliance was used). Select the item, then proceed
as follows:
4. "Reset?"; press OK;
5. "Reset complete": the appliance confirms the reset and
goes back to the previous screen.
To exit, press /ESC (B5).
8.6 Statistics
This displays statistics relating to the machine. To display the
statistics, proceed as follows:
1. Press
(B6) to enter the "Settings" menu;
2. Press the selection arrows (B2 and B4) until "Statistics" is
displayed between the two lines;
3. Press OK (B3): statistics on the appliance are displayed, use
the selection arrows to scroll through the items;
4. Press
/ESC (B5) to exit.
To go back to the main screen, press /ESC.
9. RINSING
Use this function to deliver hot water from the coffee spouts
(A9) and hot water spout (C6), if inserted, to clean and heat the
appliance's internal circuit.
Place a container with a minimum capacity of 100ml under the
coffee and hot water spouts.
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
12
Advertisement
Table of Contents
Troubleshooting
