Summary of Contents for Dodge Challenger SRT Includes 392/Hellcat 2016
Page 1
Challenger 2 0 1 6 O W N E R ’ S M A N U A L SRT Includes 392/Hellcat...
Page 2
VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name FCA features and equipment that are either standard or op- US LLC shall be deemed to be deleted and the name FCA tional on this vehicle.
Page 3
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ............. . . 3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained tech- Congratulations on selecting your new FCA US LLC nicians and genuine MOPAR® parts, and cares about vehicle. Be assured that it represents precision workman- your satisfaction.
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. VIN Location NOTE: It is illegal to remove or alter the VIN.
Page 11
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS ▫ Rearming Of The System ....19 A WORD ABOUT YOUR KEYS ... . .12 ▫...
Page 12
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Programming Additional Key Fobs ..25 ▫ Manual Door Locks .....31 ▫...
Page 13
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Supplemental Restraint System (SRS) ..57 ▫ Exhaust Gas ......95 ▫...
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS NOTE: In case the ignition does not change with the push of a button, the key fob may have a low or dead Your vehicle uses a keyless ignition system. This system battery.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fobs NOTE: SRT vehicles, equipped with the 6.2L Super- charged engine, come with three key fobs (two red and one black) that allow for different engine power levels. Please refer to the Drive Modes in the “Uconnect Settings”...
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Mechanical Latch On The Back Of The Key Fob Emergency Key Removal NOTE: You can insert the double-sided emergency key into the lock cylinders with either side up. Ignition Or Accessory On Message When opening the driver’s door when the ignition is in ACC or ON (engine not running), a chime will sound to...
Page 17
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 remind you to cycle the ignition to OFF. In addition to the WARNING! (Continued) chime, the ignition or accessory on message will display Enter-N-Go, always make sure the keyless ignition in the cluster. node is in “OFF”...
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information WARNING! (Continued) The following regulatory statement applies to all Radio • Do not leave the key fob in or near the vehicle, or Frequency (RF) devices equipped in this vehicle: in a location accessible to children, and do not leave the ignition of a vehicle equipped with This device complies with Part 15 of the FCC Rules and...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 SENTRY KEY indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, The Sentry Key Immobilizer system prevents unauthor- it indicates that someone used an invalid key fob to start ized vehicle operation by disabling the engine.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! (Continued) CAUTION! • The Sentry Key Immobilizer system is not compat- • Always remove the key fobs from the vehicle and ible with some aftermarket remote starting sys- lock all doors when leaving the vehicle unat- tems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Customer Key Fob Programming VEHICLE SECURITY ALARM Programming key fobs may be performed at an autho- The Vehicle Security Alarm monitors the vehicle doors rized dealer. and trunk for unauthorized entry and the ignition switch for unauthorized operation.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Push the LOCK To Arm The System button on the exterior Passive Entry Door Handle with a valid key fob available Follow these steps to arm the Vehicle Security Alarm: in the same exterior zone (refer to Keyless Enter- 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 • Advance the vehicle ignition system out of the OFF Vehicle Security Alarm will arm regardless of whether position. you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ILLUMINATED ENTRY REMOTE KEYLESS ENTRY The courtesy lights will turn on when you use the key fob The Remote Keyless Entry system allows you to lock or to unlock the doors or open any door. unlock the doors, open the trunk, or activate the Panic Alarm from distances up to approximately 66 ft (20 m) This feature also turns on the approach lighting in the...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 If the vehicle is equipped with Passive Entry, refer to “Keyless Enter-N-Go — Passive Entry” under “Things To Know Before Starting Your Vehicle” for further informa- tion. 1st Press Of Key Fob Unlocks This feature lets you program the system to unlock either the driver’s door or all doors on the first push of the UNLOCK...
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Headlight Illumination On Approach Sound Horn With Lock This feature activates the headlights for up to 90 seconds This feature will cause the horn to chirp when the doors are locked with the key fob. This feature can be turned on when the doors are unlocked with the key fob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 and release. When the Panic Alarm is activated, the Programming Additional Key Fobs turn signals will flash, the horn will pulse on and off, Programming key fobs may be performed at an autho- and the interior lights will turn on.
Page 28
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Emergency Key Removal Separating Key Fob Case 2. Separating key fob halves requires screw removal, if 3. Remove the battery by turning the back cover over equipped, and gently prying the two halves of the key (battery facing downward) and tapping it lightly on a fob apart.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 new battery with your fingers. Skin oils may cause NOTE: Changes or modifications not expressly approved battery deterioration. If you touch a battery, clean it by the party responsible for compliance could void the with rubbing alcohol.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use Remote Start WARNING! All of the following conditions must be met before the • Do not start or run an engine in a closed garage or engine will remote start: confined area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • Remote Start Aborted — Fuel Low • The park lamps will turn on and remain on during Remote Start mode. • Remote Start Disabled — Start Vehicle To Reset • For security, power window and power sunroof op- The instrument cluster message stays active until the eration (if equipped) are disabled when the vehicle is ignition is placed in the ON/RUN position.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To avoid unintentional shut downs, the system Cancel Remote Start will disable the one time push of the REMOTE START Remote Starting will also cancel if any of the following button for two seconds after receiving a valid occur: Remote Start request.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) be in a vehicle unattended is dangerous for a • For personal security and safety in the event of a number of reasons. A child or others could be collision, lock the vehicle doors before you drive as seriously or fatally injured.
Page 35
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 If you push the power door lock switch while the ignition is on, and either door is open, the power locks will not operate. This prevents you from accidentally locking the key fob in the vehicle. Turning off the ignition or closing the door will allow the locks to operate.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock Doors On Exit Automatic Unlock Doors On Exit Programming — If Equipped The doors will unlock automatically if: The Automatic Unlock Doors On Exit feature can be 1. The Automatic Unlock Doors On Exit feature is enabled. enabled or disabled.
Page 37
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 NOTE: • Passive Entry may be programmed ON/OFF; refer to “Uconnect Settings” in “Understanding Your Instru- ment Panel” for further information. • If wearing gloves on your hands, or if it has been raining on the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a slower re- sponse time.
Page 38
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock From The Passenger Side: FOBIK-Safe only executes in vehicles with passive entry. There are three situations that trigger a FOBIK-Safe With a Passive Entry key fob within 5 ft (1.5 m) of the search in any passive entry vehicle.
Page 39
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 NOTE: The vehicle will only unlock the doors when a valid Passive Entry key fob is detected inside the vehicle, and no valid Passive Entry key fob is detected outside the vehicle. The vehicle will not unlock the doors when any of the following conditions are true: •...
Page 40
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Lock The Vehicle’s Doors: Do NOT grab the door handle, when pushing the door handle button. This could unlock the door(s). With one of the vehicle’s Passive Entry key fobs within ft (1.5 m) of the driver or passenger front door handles, push the door handle LOCK button to lock both doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 NOTE: General Information • After pushing the door handle button, you must wait The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle: two seconds before you can lock or unlock the doors, using either Passive Entry door handle.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS There is a single window control on the passenger’s door trim panel that operates the window on the passenger’s Power Windows door. The window controls will operate only when the The window controls on the driver’s door control both of ignition switch is in the ON/RUN or ACC position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 To open the window part way, push the window switch WARNING! to the first detent and release it when you want the window to stop. Never leave children unattended in a vehicle, and do not let children play with power windows.
Page 44
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The transmission must be in PARK before the With the ignition switch in the ON/RUN position, the button will operate. If equipped with a manual transmis- Trunk Open symbol will display in the instrument cluster sion, the vehicle speed must be under 5 MPH (8 km/h) indicating that the trunk is open.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 TRUNK SAFETY WARNING trunk, the trunk can be opened by actuating the glow-in- the-dark handle attached to the trunk latching mecha- WARNING! nism. Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINT SYSTEMS 2. If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, Some of the most important safety features in your move the seat as far back as possible and use the vehicle are the restraint systems: proper child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 6. All occupants should always wear their lap and WARNING! shoulder belts properly. • Never place a rear-facing child restraint in front of 7. The driver and front passenger seats should be moved an air bag.
Page 48
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ejection and the risk of injury caused by striking the the Seat Belt Reminder Light will turn on and remain on inside of the vehicle. Everyone in a motor vehicle should until both outboard front seat belts are buckled. The be belted at all times.
Page 49
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Change Of Status NOTE: If BeltAlert has been deactivated and the driver or outboard front seat passenger (if equipped with out- If the driver or outboard front seat passenger (if board front passenger seat BeltAlert) is unbuckled the equipped with outboard front passenger seat BeltAlert) Seat Belt Reminder Light will turn on and remain on until unbuckles their seat belt while the vehicle is traveling,...
Page 50
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Do not allow people to ride in any area of your • Relying on the air bags alone could lead to more vehicle that is not equipped with seats and seat severe injuries in a collision.
Page 51
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! (Continued) WARNING! (Continued) • A lap belt worn too high can increase the risk of • A seat belt that is too loose will not protect you injury in a collision. The seat belt forces won’t be at properly.
Page 52
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE pull out the seat belt. Slide the latch plate up the WARNING! (Continued) webbing as far as necessary to allow the seat belt to go wear your shoulder belt. The lap and shoulder belt around your lap.
Page 53
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Inserting Latch Plate Into Buckle Positioning The Lap Belt 4. Position the lap belt so that it is snug and lies low 5. Position the shoulder belt across the shoulder and across your hips, below your abdomen. To remove chest with minimal, if any slack so that it is comfort- slack in the lap belt portion, pull up on the shoulder able and not resting on your neck.
Page 54
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE position. If necessary, slide the latch plate down the Seat Belt Extender webbing to allow the seat belt to retract fully. If a seat belt is not long enough to fit properly, even when the webbing is fully extended and the adjustable upper Lap/Shoulder Belt Untwisting Procedure shoulder belt anchorage (if equipped) is in its lowest...
Page 55
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Seat Belts And Pregnant Women WARNING! (Continued) • Using a Seat Belt Extender when not needed can increase the risk of serious injury or death in a collision. Only use the Seat Belt Extender when the lap belt is not long enough and only use in the recommended seating positions.
Page 56
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Position the lap belt snug and low below the abdomen The pretensioners are triggered by the Occupant Re- and across the strong bones of the hips. Place the straint Controller (ORC). Like the air bags, the preten- shoulder belt across the chest and away from the neck.
Page 57
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Restraints Using The Vehicle Seat Belt” under the “Child If the passenger seating position is equipped with an Restraints” section of this manual. The table below ALR and is being used for normal usage, only pull the defines the type of feature for each seating position.
Page 58
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Disengage The Automatic Locking Mode WARNING! Unbuckle the combination lap/shoulder belt and allow it • Never place a rear-facing child restraint in front of to retract completely to disengage the Automatic Locking an air bag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 • Supplemental Side Air Bags WARNING! (Continued) • Front and Side Impact Sensors only used to install rear-facing or forward-facing child restraints that have a harness for restraining • Seat Belt Pretensioners the child.
Page 60
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel.
Page 61
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 output appropriate to the severity and type of collision as WARNING! determined by the Occupant Restraint Controller (ORC), • No objects should be placed over or near the air which may receive information from the front impact sensors or other system components.
Page 62
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Because air bag sensors measure vehicle deceleration WARNING! (Continued) over time, vehicle speed and damage by themselves are some collisions, air bags won’t deploy at all. Al- not good indicators of whether or not an air bag should ways wear your seat belts even though you have air have deployed.
Page 63
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Knee Impact Bolsters SABs are marked with a “SRS AIRBAG” or “AIR- BAG” label sewn into the outboard side of the seats. The Knee Impact Bolsters help protect the knees of the driver and front passenger, and position the front occu- pants for improved interaction with the Advanced Front Air Bags.
Page 64
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the SAB deploys, it opens the seam on the out- 2. Supplemental Side Air Bag Inflatable Curtains board side of the seatback’s trim cover. The inflating SAB (SABICs): Located above the side windows. The trim deploys through the seat seam into the space between the covering the SABICs is labeled “SRS AIRBAG”...
Page 65
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 SABICs may help reduce the risk of head or other injuries WARNING! to front and rear seat outboard occupants in certain side • Your vehicle is equipped with left and right impacts and/or vehicle rollover events, in addition to the injury reduction potential provided by the seat belts and Supplemental Side Air Bag Inflatable Curtains body structure.
Page 66
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The SABICs and SABs (“Side Air Bags”) are designed to help keep you in position, away from inflating Side Air activate in certain side impacts and certain rollover Bags. To get the best protection from the Side Air Bags, events.
Page 67
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 The Side Air Bags will not deploy in all side collisions, WARNING! (Continued) including some collisions at certain angles, or some side properly. In some collisions, Side Air Bags won’t collisions that do not impact the area of the passenger deploy at all.
Page 68
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE faster-developing event may deploy the seat belt preten- deploy and unfold. The abrasions are similar to fric- sioners as well as the Side Air Bags on both sides of the tion rope burns or those you might get sliding along a vehicle.
Page 69
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Do not drive your vehicle after the air bags have de- Enhanced Accident Response System ployed. If you are involved in another collision, the air In the event of an impact, if the communication network bags will not be in place to protect you.
Page 70
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System Reset START or ON/RUN position. If the ignition is in the OFF Procedure position or in the ACC position, the air bag system is not on and the air bags will not inflate. In order to reset the Enhanced Accident Response System functions after an event, the ignition must be changed The ORC contains a backup power supply system that...
Page 71
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 diagnostics also record the nature of the malfunction. WARNING! While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized Ignoring the Air Bag Warning Light in your instru- dealer service the air bag system immediately.
Page 72
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the Redundant Air Bag Warning Light comes on WARNING! (Continued) intermittently or remains on while driving have an modify the front bumper, vehicle body structure, or authorized dealer service the vehicle immediately. For add aftermarket side steps or running boards.
Page 73
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Event Data Recorder (EDR) These data can help provide a better understanding of the circumstances in which crashes and injuries occur. This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in NOTE: EDR data are recorded by your vehicle only if a certain crash or near crash-like situations, such as an air non-trivial crash situation occurs;...
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraints enough for an adult safety belt. Always check the child seat Owner’s Manual to make sure you have the correct Everyone in your vehicle needs to be buckled up at all seat for your child.
Page 75
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Recommended Type Of Weight Or Age Child Restraint Infants and Toddlers Children who are two years old or Either an Infant Carrier or a younger and who have not Convertible Child Restraint, facing reached the height or weight limits...
Page 76
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Size, Height, Recommended Type Of Weight Or Age Child Restraint Children Too Large for Children 12 years old or younger, Vehicle Seat Belt, seated in the rear Child Restraints who have out-grown the height or seat of the vehicle weight limit of their booster seat Infants And Child Restraints...
Page 77
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 All children whose weight or height is above the WARNING! (Continued) forward-facing limit for the child seat should use a 12 years or younger, including a child in a rear- belt-positioning booster seat until the vehicle’s seat belts facing child restraint.
Page 78
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large For Booster Seats WARNING! (Continued) Children who are large enough to wear the shoulder belt • After a child restraint is installed in the vehicle, do comfortably, and whose legs are long enough to bend not move the vehicle seat forward or rearward over the front of the seat when their back is against the because it can loosen the child restraint attach-...
Page 79
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 4. Is the lap part of the belt as low as possible, touching WARNING! the child’s thighs and not their stomach? Never allow a child to put the shoulder belt under an 5.
Page 80
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints Restraint Type Combined Use any attachment method shown with an “X” Below Weight of the LATCH – Seat Belt Only LATCH – Seat Belt + Top Child + Child Lower Anchors Lower Anchors Tether Anchor...
Page 81
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Lower Anchors And Tethers For CHildren has three vehicle anchor points for installing LATCH- (LATCH) Restraint System equipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
Page 82
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH Positions For Installing Child Restraints In This Vehicle • Lower Anchorage Symbol 2 anchorages per seating position • Top Tether Anchorage Symbol...
Page 83
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s weight + 65 lbs (29.5 kg) Use the LATCH anchorage system until the weight of the child restraint) for using the combined weight of the child and the child LATCH anchorage system to attach the restraint is 65 lbs (29.5 kg).
Page 84
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Frequently Asked Questions About Installing Child Restraints With LATCH Can the rear-facing child restraint touch the The child seat may touch the back of the back of the front passenger seat? front passenger seat if the child restraint manufacturer also allows contact.
Page 85
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Locating Tether Anchorages There are tether strap anchorages behind each rear seating position located in the panel be- tween the rear seatback and the rear window. They are found under a plastic cover with the tether anchorage symbol on it.
Page 86
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center Seat LATCH If a child restraint installed in the center position blocks the seat belt webbing or buckle for the outboard position,...
Page 87
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Always follow the directions of the child restraint restraint to get a better fit. If the rear seat can be moved manufacturer when installing your child restraint. Not forward and rearward in the vehicle, you may wish to all child restraint systems will be installed as described move it to its rear-most position to make room for the here.
Page 88
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. Test that the child restraint is installed tightly by the seat belt. Remind all children in the vehicle that the pulling back and forth on the child seat at the belt seat belts are not toys and that they should not play with path.
Page 89
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Installing Child Restraints Using The Vehicle Seat Lap/Shoulder Belt Systems for Installing Child Belt Restraints in this Vehicle The seat belts in the passenger seating positions are equipped with a Switchable Automatic Locking Retractor (ALR) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip.
Page 90
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s Weight limit of the Child Restraint Always use the tether anchor when weight + weight of the child re- using the seat belt to install a straint) for using the Tether Anchor forward facing child restraint, up...
Page 91
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 Installing A Child Restraint With A Switchable 5. To lock the seat belt, pull down on the shoulder part of Automatic Locking Retractor (ALR) the belt until you have pulled all the seat belt webbing out of the retractor.
Page 92
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE strap. See the section “Installing Child Restraints WARNING! (Continued) Using the Top Tether Anchorage” for directions to tether strap of a rear-facing car seat to the tether attach a tether anchor. anchorage that is approved for that seating position, 9.
Page 93
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available. 2.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Remove slack in the tether strap according to the child Transporting Pets restraint manufacturer’s instructions. Air Bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly WARNING! injured, or injure a passenger during panic braking or in a collision.
Page 95
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 It is recommended for the operator to observe the follow- 100 to 300 miles (161 to 483 km): ing driving behaviors during the new vehicle break-in • Depress the accelerator pedal slowly and not more period: than halfway to avoid rapid acceleration in lower 0 to 100 miles (0 to 161 km):...
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For the first 1500 mi (2414 km): WARNING! • Do not participate in track events, sport driving • Do not leave children or animals inside parked schools, or similar activities during the first 1500 mi vehicles in hot weather.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Exhaust Gas WARNING! (Continued) • If it is necessary to sit in a parked vehicle with the WARNING! engine running, adjust your heating or cooling Exhaust gases can injure or kill. They contain carbon controls to force outside air into the vehicle.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The driving, have the system inspected at an authorized Vehicle dealer as soon as possible. This light will illuminate with a single chime when a fault with the Air Bag Seat Belts Warning Light has been detected, it will stay on until Inspect the seat belt system periodically, checking for...
Page 99
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 cannot slip out of position and interfere with the pedals WARNING! (Continued) or impair safe operation of your vehicle in other ways. mats and other coverings will reduce the size of the pedal area and interfere with the pedals.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside Door Latches The Vehicle Check for proper closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
Page 101
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS MIRRORS ......105 BLIND SPOT MONITORING (BSM) — IF EQUIPPED.
Page 102
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Manual Front Seatback Recline ...131 ▫ Lights-On Reminder ....143 ▫...
Page 103
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 ▫ Headlights On With Wipers (Available With ▫ To Vary The Speed Setting ....157 Automatic Headlights Only) ... . .150 ▫...
Page 104
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Overtake Aid ......173 PARKSENSE REAR PARK ASSIST — IF EQUIPPED .
Page 105
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 ▫ Sunglasses Storage ....201 ▫ Closing Sunroof — Express....211 ▫...
Page 106
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE ......218 REAR WINDOW FEATURES ....220 ▫...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 MIRRORS Automatic Dimming Mirror — If Equipped The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. This mirror automatically adjusts for headlight glare from vehicles behind you.
Page 108
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ASSIST Call WARNING! The ASSIST Button is used to automatically connect you ALWAYS obey traffic laws and pay attention to the to any one of the following support centers: road. Some Uconnect Access services, including 9-1-1 •...
Page 109
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • The vehicle brand. 9-1-1 Call • The last known GPS coordinates of the vehicle. 1. Push the 9-1-1 Call button on the Rearview Mirror. 4. You should be able to speak with the 9-1-1 operator NOTE: In case the 9-1-1 Call button is pushed in error, through the vehicle audio system to determine if there will be a 10 second delay before the 9-1-1 Call...
Page 110
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: WARNING! • Your vehicle may be transmitting data as authorized • If anyone in the vehicle could be in danger (e.g., by the subscriber. fire or smoke is visible, dangerous road conditions •...
Page 111
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 9-1-1 Call System Limitations WARNING! (Continued) Vehicles sold in Canada and Mexico DO NOT have 9-1-1 electrical equipment to the vehicle’s electrical sys- Call system capabilities. tem. This may prevent your vehicle from sending a signal to initiate an emergency call.
Page 112
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The vehicle’s electrical systems are not intact. WARNING! • The 9-1-1 Call system software and/or hardware are • Ignoring the Rearview Mirror light could mean you damaged during a crash. will not have 9-1-1 Call services. If the Rearview •...
Page 113
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 General Information WARNING! This device complies with Part 15 of the FCC Rules. ALWAYS obey traffic laws and pay attention to the Operation is subject to the following two conditions: (1) road. Some Uconnect Access services, including 9-1-1 This device may not cause harmful interference, and (2) and Assist, will NOT work without an operable 1X this device must accept any interference received, includ-...
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors Outside Mirrors Folding Feature To receive maximum benefit, adjust the outside mirror(s) The mirrors are equipped with a rotational hinge. The to center on the adjacent lane of traffic and a slight mirrors have one detent (clockwise) towards the rear of overlap of the view obtained from the inside mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Power Mirrors The power mirror controls consist of mirror select but- tons and a four-way mirror control switch. To adjust a The power mirror controls are located on the driver-side mirror, push either the L (left) or R (right) to select the door trim panel.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vanity Mirrors A vanity mirror is located on the sun visor. To use the mirror, rotate the sun visor downward and swing the mirror cover upward. Illuminated Vanity Mirrors An illuminated vanity mirror is on the sun visor. To use the mirror, rotate the sun visor downward and swing the mirror cover upward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 your left hand pull rearwards until the sun visor is in the BLIND SPOT MONITORING (BSM) — IF desired position. To use the extender feature of the sun EQUIPPED visor, grab the extender which is located at the rear of the The Blind Spot Monitoring (BSM) system uses two radar- visor and pull rearward.
Page 118
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Transmission Vehicles The BSM system sensors operate when the vehicle is in any forward gear or REVERSE and enters stand-by mode when the vehicle is in PARK. Manual Transmission Vehicles The BSM system sensors operate when the vehicle is in any gear and enters stand-by mode when the Park Brake is engaged, the vehicle is not in REVERSE, and the vehicle is stationary.
Page 119
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas. NOTE: • The BSM system does NOT alert the driver about rapidly approaching vehicles that are outside the de- tection zones.
Page 120
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The area on the rear fascia where the radar sensors are Entering From The Side located must remain free of snow, ice, and dirt/road Vehicles that move into your adjacent lanes from either contamination so that the BSM system can function side of the vehicle.
Page 121
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Entering From The Rear Overtaking Traffic Vehicles that come up from behind your vehicle on either If you pass another vehicle slowly (with a relative speed side and enter the rear detection zone with a relative of less than 10 mph (16 km/h) and the vehicle remains in speed of less than 30 mph (48 km/h).
Page 122
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Overtaking/Approaching Overtaking/Passing The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc.
Page 123
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Stationary Objects Opposing Traffic WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM (Continued)
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicle’s mirrors, glance over your shoulder, and use your turn signal before changing lanes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 NOTE: In a parking lot situation, oncoming vehicles can Modes Of Operation be obscured by vehicles parked on either side. If the Three selectable modes of operation are available in the sensors are blocked by other structures or vehicles, the Uconnect System.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE turn signal is then activated, and it corresponds to an Blind Spot Alert Off alert present on that side of the vehicle, an audible chime When the BSM system is turned off there will be no will also be sounded.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Operation is subject to the following two conditions: WARNING! 1. The device may not cause harmful interference. • It is dangerous to ride in a cargo area, inside or 2. The device must accept any interference received, outside of a vehicle.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seats Adjusting The Seat Forward Or Rearward The power seat switches are located on the outboard side The seat can be adjusted both forward and rearward. of the front seat cushions. The power seat switches are Push the seat switch forward or rearward.
Page 129
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Power Lumbar — If Equipped Vehicles equipped with power driver or passenger seats are also equipped with power lumbar. The power lumbar switch is located on the outboard side of the power seat. Push the switch forward to increase the lumbar support.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Heated Seats — If Equipped WARNING! (Continued) The front heated seats control buttons are located within control which could cause a collision and serious the Uconnect system. You can gain access to the control injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 If the HI-level setting is selected, the system will auto- WARNING! matically switch to LO-level after approximately 60 min- • Persons who are unable to feel pain to the skin utes of continuous operation. At that time, the display because of advanced age, chronic illness, diabetes, will change from HI to LO, indicating the change.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE air through fine perforations in the seat cover to help Vehicles Equipped With Remote Start keep the driver and front passenger cooler in higher On models that are equipped with remote start, the ambient temperatures.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passenger Seat Easy Entry On the passenger seat, pull forward on the lever located on the side of the seatback in order to dump the seatback and slide the seat forward. You can also temporarily remove the seat belt from the guide loop on the seat and allow the seat belt to retract out of the way.
Page 135
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Reactive Head Restraints — Front Seats WARNING! The front driver and passenger seats are equipped with The head restraints for all occupants must be prop- Reactive Head Restraints (RHR). In the event of a rear erly adjusted prior to operating the vehicle or occu- impact the RHRs will automatically extend forward pying a seat.
Page 136
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To raise the head restraint, pull upward on the head restraint. To lower the head restraint, push the adjust- ment button located at the base of the head restraint and push downward on the head restraint. To remove the head restraint, remove the seat belt from the seat belt loop.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Folding Rear Seat WARNING! (Continued) The rear seatbacks can be folded forward to provide an stow removed head restraints in a location outside additional storage area. Pull on the loops located on the the occupant compartment.
Page 138
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seatback Loop Folded Rear Seat When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 TO OPEN AND CLOSE THE HOOD WARNING! Two latches must be released to open the hood. • Be certain that the seatback is securely locked into 1. Pull the hood release lever located under the left side position.
Page 140
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Move to the outside of the vehicle, the safety catch is located under the center front edge of the hood. Hood Safety Catch WARNING! Hood Safety Catch Location 3. Push the safety catch to the left. Be sure the hood is fully latched before driving your vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 operation of the headlights, parking lights, instrument WARNING! (Continued) panel lights, instrument panel light dimming, and inte- Failure to follow this warning could result in serious rior lights. injury or death. CAUTION! To prevent possible damage, do not slam the hood to close it.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotate the headlight switch to the second detent for Headlights On With Wipers (Available With headlight, parking light and instrument panel light op- Automatic Headlights Only) eration. When this feature is active, the headlights will turn on after the wipers are turned on if the headlight switch is Automatic Headlights placed in the AUTO position and programmable feature...
Page 143
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 mounted on the inside rearview mirror. This camera Sensitivity Control (not recommended), toggle high- detects vehicle specific light and automatically switches beam lever 6 full on/off cycles within 10 seconds of from high beams to low beams until the approaching ignition ON.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate If you turn the headlights, park lights or ignition switch ON again, the system will cancel the delay. 1. Pull the multifunction lever toward you (or rearward If you turn the headlights off before the ignition, they will in vehicle) to manually deactivate the system (normal turn off in the normal manner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 NOTE: If allowed by law in the country in which the vehicle was purchased the Daytime Running Lights can be turned on and off using the Uconnect System, refer to “Uconnect Settings” in “Understanding Your Instrument Panel”...
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: High/Low Beam Switch • If either light remains on and does not flash, or there is Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever a very fast flash rate, check for a defective outside light toward you to switch the headlights back to low beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 These lights also turn on when a door is opened, or when Interior Lights the UNLOCK button on the Remote Keyless Entry key The interior lights come on when a door is opened. fob is pushed, or when the dimmer control is turned fully To protect the battery, the interior lights will turn off upward, past the second detent.
Page 148
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dimmer Controls With the parking lights or headlights on, rotating the left dimmer control upward will increase the brightness of The dimmer control is part of the headlight switch and is the instrument panel lights and lighted cupholders (if located on the left side of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Dome Light Position WINDSHIELD WIPERS AND WASHERS Rotate the left dimmer control completely upward to the second detent to turn on the interior lights. The interior The multifunction lever operates the windshield lights will remain on when the dimmer control is in this wipers and washer when the ignition is placed in position.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotate the end of the multifunction lever to the first wipe interval from a minimum of one cycle every second detent past the intermittent settings for low-speed wiper to a maximum of approximately 36 seconds between operation, or to the second detent past the intermittent cycles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Windshield Washers WARNING! To use the washer, push the multifunction lever inward Sudden loss of visibility through the windshield (toward the steering column) and hold it for as long as could lead to a collision. You might not see other washer spray is desired.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights On With Wipers (Available With The Headlights On with Wipers feature can be turned on Automatic Headlights Only) and off using the Uconnect System, refer to “Uconnect Settings” in “Understanding Your Instrument Panel” for When this feature is active, the headlights will turn on further information.
Page 153
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 wiper sensitivity. Setting 4 can be used if the driver The Rain Sensing system has protection features for the desires more sensitivity. Place the wiper switch in the wiper blades and arms, and will not operate under the OFF position when not using the system.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MANUAL TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping lever is located below the steering wheel at the end of the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The heated steering wheel control button is located WARNING! within the Uconnect system. You can gain access to the control button through the climate screen or the controls Do not adjust the steering column while driving. screen.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 The Electronic Speed Control buttons are located on the WARNING! right side of the steering wheel. • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion, or other physical conditions must exercise care when using the steering wheel heater.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Elec- WARNING! tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at Leaving the Electronic Speed Control system on the same time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 To Deactivate The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “Under- A soft tap on the brake pedal, pushing the CANCEL standing Your Instrument Panel” for more information. button, or normal brake pressure while slowing the The speed increment shown is dependant on the chosen vehicle will deactivate the Electronic Speed Control with-...
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the button is continually pushed, the set speed will • If the button is continually pushed, the set speed will continue to increase until the button is released, then continue to decrease until the button is released, then the new set speed will be established.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 NOTE: The Electronic Speed Control system maintains ADAPTIVE CRUISE CONTROL (ACC) — IF speed up and down hills. A slight speed change on EQUIPPED moderate hills is normal. Adaptive Cruise Control (ACC) increases the driving convenience provided by cruise control while traveling On steep hills, a greater speed loss or gain may occur so on highways and major roadways.
Page 162
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the ACC sensor detects a vehicle ahead, ACC will You can change the mode by using the Cruise Control apply limited braking or acceleration (not to exceed buttons. The two control modes function differently. the original set speed) automatically to maintain a Always confirm which mode is selected.
Page 163
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 WARNING! (Continued) WARNING! (Continued) • The ACC system: • When entering a turn lane or highway off ramp; • Does not react to pedestrians, oncoming vehicles, when driving on roads that are winding, icy, snow- covered, slippery, or have steep uphill or downhill and stationary objects (e.g., a stopped vehicle in a slopes.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adaptive Cruise Control (ACC) Operation The speed control buttons (located on the right side of the steering wheel) operates the ACC system. Adaptive Cruise Control Buttons 1 — Normal (Fixed Speed) 5 — Distance Setting Increase Cruise Control On/Off 6 —...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 NOTE: Any chassis/suspension or tire size modifications NOTE: You cannot engage ACC under the following to the vehicle will effect the performance of the Adaptive conditions: Cruise Control and Forward Collision Warning System. •...
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate/Deactivate To turn the system OFF, push and release the Adaptive Cruise Control (ACC) ON/OFF button again. At this Push and release the Adaptive Cruise Control (ACC) time, the system will turn off and the DID will display ON/OFF button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Remove your foot from the accelerator pedal. If you do WARNING! not, the vehicle may continue to accelerate beyond the set speed. If this occurs: Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous. You could acciden- •...
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The gear selector is removed from the Drive position. To Resume • The Electronic Stability Control/Traction Control Sys- If there is a set speed in memory push the RES (resume) button and then remove your foot from the accelerator tem (ESC/TCS) activates.
Page 169
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 • If the button is continually pushed, the set speed will The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “ Under- continue to increase in 10 km/h increments until the standing Your Instrument Panel”...
Page 170
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the button is continually pushed, the set speed will • When you use the SET - button to decelerate, if the continue to decrease in 5 mph increments until the engine’s braking power does not slow the vehicle button is released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Setting The Following Distance In ACC The specified following distance for ACC can be set by varying the distance setting between four bars (longest), three bars (long), two bars (medium) and one bar (short). Using this distance setting and the vehicle speed, ACC calculates and sets the distance to the vehicle ahead.
Page 172
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Distance Setting 3 Bars (Long) Distance Setting 2 Bars (Medium)
Page 173
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 To decrease the distance setting, push the Distance Set- ting — Decrease button and release. Each time the button is pushed, the distance setting decreases by one bar (shorter). If there is no vehicle ahead, the vehicle will maintain the set speed.
Page 174
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The system disengages. (Refer to the information on ACC Activation). The maximum braking applied by ACC is limited; how- ever, the driver can always apply the brakes manually, if necessary. NOTE: The brake lights will illuminate whenever the ACC system applies the brakes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Overtake Aid Adaptive Cruise Control Ready When driving with ACC engaged and following a ve- When ACC is activated but the vehicle speed setting has hicle, the system will provide an additional acceleration not been selected, the display will read “Adaptive Cruise up to the ACC set speed to assist in passing the vehicle.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • ACC Unavailable Warning The “ACC/FCW Unavailable Wipe Front Radar Sensor” message can sometimes be displayed while driving in • The DID will return to the last display selected after highly reflective areas (i.e. tunnels with reflective tiles, or five seconds of no ACC display activity ice and snow).
Page 177
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 To keep the ACC System operating properly, it is impor- When the condition that deactivated the system is no tant to note the following maintenance items: longer present, the system will return to the “Adaptive Cruise Control Off”...
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Service ACC/FCW Warning Precautions While Driving With ACC If the system turns off, and the DID displays “ACC/FCW In certain driving situations, ACC may have detection Unavailable Service Required” or “Cruise/FCW Unavail- issues. In these cases, ACC may brake late or unexpect- able Service Required”, there may be an internal system edly.
Page 179
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 the vehicle is out of the curve the system will resume your original Set Speed. This is a part of normal ACC system functionality. NOTE: On tight turns ACC performance may be limited. Offset Driving Condition Example Turns And Bends When driving on a curve with ACC engaged, the system...
Page 180
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using ACC On Hills Lane Changing When driving on hills, ACC may not detect a vehicle in ACC may not detect a vehicle until it is completely in the your lane. Depending on the speed, vehicle load, traffic lane in which you are traveling.
Page 181
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Narrow Vehicles Some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There may not be sufficient distance to the vehicle ahead.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Stationary Objects And Vehicles General Information ACC does not react to stationary objects and stationary This vehicle has systems that operate on radio frequency vehicles. For example, ACC will not react in situations that comply with Part 15 of the Federal Communications where the vehicle you are following exits your lane and Commission (FCC) rules and with Industry Canada...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 Normal (Fixed Speed) Electronic Speed Control WARNING! Mode In the normal Cruise Control mode, the system will In addition to Adaptive Cruise Control mode, a Normal not react to vehicles ahead. In addition, the proximity (Fixed Speed) Electronic Speed Control mode is available warning does not activate and no alarm will sound for cruising at fixed speeds.
Page 184
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Once a speed has been set a message (CRUISE CON- U.S. Speed (mph) TROL SET TO MPH/KM) will appear indicating what • Pushing the SET + button once will result in a 1 mph speed was set.
Page 185
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 To Decrease Speed Metric Speed (km/h) • Pushing the SET - button once will result in a 1 km/h When the Normal (Fixed Speed) Cruise Control is set, you can decrease speed by pushing the SET - button. decrease in set speed.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The vehicle parking brake is applied. • The Adaptive Cruise Control (ACC) On/Off button is pushed. • The braking temperature exceeds normal range (over- heated). FORWARD COLLISION WARNING (FCW) — IF EQUIPPED •...
Page 187
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 NOTE: FCW monitors the information from the forward looking sensors as well as the Electronic Brake Controller (EBC), to calculate the probability of a forward collision. When the system determines that a forward collision is probable, the driver will be provided with audible and visual warnings.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: WARNING! (Continued) • The minimum speed for FCW activation is 5 mph responsibility to avoid a collision by controlling the (10 km/h). vehicle via braking and steering. Failure to follow this warning could lead to serious injury or death. •...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Changing the FCW status to “Off” prevents the system Changing the FCW status to the “Near” setting, allows from warning you of a possible collision with the vehicle the system to warn you of a possible collision with the in front of you.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Service FCW Warning ParkSense will retain the last system state (enabled or disabled) from the last ignition cycle when the ignition is If the system turns off, and the DID displays: changed to the ON/RUN position. •...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 ParkSense Warning Display The system will indicate a detected obstacle by showing a single arc in one or more regions based on the obstacle’s The ParkSense Warning screen will only be displayed if distance and location relative to the vehicle.
Page 192
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Single 1/2 Second Tone/Solid Arc Slow Tone/Solid Arc...
Page 193
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 Fast Tone/Flashing Arc Continuous Tone/Flashing Arc The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle:...
Page 194
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING ALERTS Rear Greater 79-59 in 59-47 in 47-39 in 39-25 in 25-12 in Less than Distance than (200- (150- (120- (100-65 cm) (65-30 cm) 12 in (in/cm) 79 in 150 cm) 120 cm) 100 cm) (30 cm) (200 cm)
Page 195
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 WARNING ALERTS Rear Greater 79-59 in 59-47 in 47-39 in 39-25 in 25-12 in Less than Distance than (200- (150- (120- (100-65 cm) (65-30 cm) 12 in (in/cm) 79 in 150 cm) 120 cm) 100 cm) (30 cm) (200 cm)
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Enabling And Disabling ParkSense When the ParkSense system is disabled, the Drivers Information Display (DID) will display ParkSense can be enabled and disabled with the the “PARKSENSE OFF” message for approxi- ParkSense switch, located on the switch panel below the mately five seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 Service The ParkSense Rear Park Assist System If “PARKSENSE UNAVAILABLE WIPE REAR SEN- SORS” appears in the Driver Information Display (DID), During vehicle start up, when the ParkSense Rear Park make sure the outer surface and the inside of the rear Assist System has detected a faulted condition, the fascia/bumper is clean and clear of snow, ice, mud, dirt instrument cluster will actuate a single chime, once per...
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • ParkSense will reduce the volume of the radio when it ParkSense System Usage Precautions is sounding an audio tone. NOTE: • Clean the ParkSense sensors regularly, taking care not • Ensure that the rear bumper is free of snow, ice, mud, to scratch or damage them.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 WARNING! CAUTION! (Continued) the sensors will not be detected when they are in Drivers must be careful when backing up even when close proximity. using the Rear Park Assist system. Always check • The vehicle must be driven slowly when using carefully behind your vehicle, and be sure to check ParkSense in order to be able to stop in time when for pedestrians, animals, other vehicles, obstructions,...
Page 200
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE license plate. The image will be displayed in the touch- When the Vehicle is shifted out of Reverse (with camera screen display along with a caution note to “check entire delay turned OFF) the rear camera mode is exited and the surroundings”...
Page 201
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 The following table shows the approximate distances for each zone: Zone Distance to the rear of the vehicle 0 - 1 ft (0 - 30 cm) Yellow 1 ft - 6.5 ft (30 cm - 2 m) Green 6.5 ft or greater (2 m or greater) WARNING!
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. OVERHEAD CONSOLE The overhead console contains courtesy/reading lights and sunglass storage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 These lights also turn on when a door is opened, when The HomeLink buttons that are located in the overhead the UNLOCK button on the Remote Keyless Entry key console designate the three different HomeLink channels. fob is pushed, or when the dimmer control is turned fully The HomeLink indicator is located on the left side of the upward past the second detent.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Before You Begin Programming HomeLink NOTE: • Erasing all channels should only be performed when Be sure that your vehicle is parked outside of the garage before you begin programming. programming HomeLink for the first time. Do not erase channels when programming additional buttons.
Page 205
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to program while keeping the HomeLink indicator light in view. 3. Push and hold the HomeLink button you want to program while you push and hold the hand-held transmitter button.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Firmly push and release the “LEARN” or “TRAIN- Reprogramming A Single HomeLink Button ING” button. On some garage door openers/devices (Rolling Code) there may be a light that blinks when the garage door To reprogram a channel that has been previously trained, opener/device is in the LEARN/TRAIN mode.
Page 207
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 • To program the two remaining HomeLink buttons, 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to program repeat each step for each remaining button. DO NOT while keeping the HomeLink indicator light in view.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Canadian/Gate Operator Programming 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to For programming transmitters in Canada/United States program while keeping the HomeLink indicator light that require the transmitter signals to “time-out”...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 NOTE: 2. Push and hold the desired HomeLink button until the indicator light begins to flash after 20 seconds. Do not • If the indicator light stays on constantly, program- release the button. ming is complete and the garage door/device should activate when the HomeLink button is pushed.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Push the LEARN button on the Garage Door Opener Security to complete the training for a Rolling Code. It is advised to erase all channels before you sell or turn • Did you unplug the device for programming and in your vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 General Information WARNING! (Continued) This device complies with Part 15 of the FCC Rules and pets or other objects are in the path of the door or with Industry Canada licence-exempt RSS standard(s). gate.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located between the sun • Never leave children unattended in a vehicle, or visors on the overhead console. with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location accessible to children.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 movement. The sunroof and sunshade will remain in a WARNING! (Continued) partially opened condition until the sunroof switch is • Do not allow small children to operate the sunroof. pushed again. Never allow your fingers, other body parts, or any Closing Sunroof —...
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Feature Sunshade Operation This feature will detect an obstruction in the opening of The sunshade can be opened manually. However, the the sunroof during Express Close operation. If an ob- sunshade will open automatically as the sunroof opens. struction in the path of the sunroof is detected, the NOTE: The sunshade cannot be closed if the sunroof is sunroof will automatically retract.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 Sunroof Maintenance The power outlets are labeled with either a “key” or a “battery” symbol to indicate how the outlet is powered. Use only a nonabrasive cleaner and a soft cloth to clean Power outlets labeled with a “key”...
Page 216
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To ensure proper operation, a MOPAR cigar knob and element must be used. The front power outlet is located next to the storage area on the integrated center stack of the instrument panel. Power Outlet —...
Page 217
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. •...
Page 218
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) CAUTION! (Continued) • Do not touch with wet hands. • Accessories that draw higher power (i.e., coolers, • Close the lid when not in use and while driving the vacuum cleaners, lights, etc.), will degrade the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 CUPHOLDERS Front Cupholders The front cupholders are located in the center console and in the door panels. Door Cupholder WARNING! If containers of hot liquid are place in the cupholder, they can spill when the door is closed, burning the Front Cupholders occupants.
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cupholders STORAGE The rear seat cupholders are located in the center armrest Glove Compartment between the rear seats. The cupholders are positioned The glove compartment is located on the passenger side forward in the armrest and side-by-side to provide conve- of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 may also be equipped with a Universal Consumer Inter- face (UCI). UCI supports Mini, 4G, Photo, Nano, 5G iPod and iPhone devices. Refer to “Universal Consumer Inter- face (UCI) — If Equipped” in “Understanding Your Instrument Panel”...
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To prevent excessive battery drain, use the rear WARNING! window defroster only when the engine is operating. Do not operate this vehicle with a console compart- CAUTION! ment lid in the open position. Driving with the console compartment lid open may result in injury in Failure to follow these cautions can cause damage to a collision.
Page 223
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT PANEL FEATURES ..225 DRIVER INFORMATION DISPLAY (DID) ..260 ▫ Engine Oil Life Reset ....262 INSTRUMENT CLUSTER —...
226 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — SRT Instrument Cluster For SRT 6.4L...
Page 229
UNDERSTANDING YOUR INSTRUMENT PANEL 227 • 1. Tachometer The fuel pump symbol points to the side of the • Indicates the engine speed in revolutions per minute vehicle where the fuel filler door is located. (RPM x 1000). 5. Temperature Gauge •...
Page 230
228 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! CAUTION! A hot engine cooling system is dangerous. You or Driving with a hot engine cooling system could others could be badly burned by steam or boiling damage your vehicle. If the temperature gauge reads coolant.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 INSTRUMENT CLUSTER — SRT Instrument Cluster For SRT 6.2L Supercharged...
Page 232
230 UNDERSTANDING YOUR INSTRUMENT PANEL • 1. Tachometer The fuel pump symbol points to the side of the • Indicates the engine speed in revolutions per minute vehicle where the fuel door is located. (RPM x 1000). 5. Temperature Gauge •...
UNDERSTANDING YOUR INSTRUMENT PANEL 231 WARNING AND INDICATOR LIGHTS WARNING! (Continued) IMPORTANT: The warning / indicator lights switch on for service if your vehicle overheats. If you decide to in the instrument panel together with a dedicated mes- look under the hood yourself, see “Maintaining Your sage and/or acoustic signal when applicable.
232 UNDERSTANDING YOUR INSTRUMENT PANEL Red Telltale Indicator Lights Seat Belt Reminder Warning Light Red Telltale What It Means Light Seat Belt Reminder Warning Light When the ignition is first placed in the ON/RUN, if the driver’s seat belt is unbuckled, a chime will sound and the light will turn on.
Page 235
UNDERSTANDING YOUR INSTRUMENT PANEL 233 Air Bag Warning Light Red Telltale What It Means Light Air Bag Warning Light This light will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN position. If the light is either not on during startup, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.
Page 236
234 UNDERSTANDING YOUR INSTRUMENT PANEL Brake Warning Light Red Telltale What It Means Light Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
Page 237
UNDERSTANDING YOUR INSTRUMENT PANEL 235 The light will remain on until the cause is corrected. Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- Operation of the Brake Warning Light can be checked by tions.
Page 238
236 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Security Warning Light — If Equipped Red Telltale What It Means Light Vehicle Security Warning Light — If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed.
Page 239
UNDERSTANDING YOUR INSTRUMENT PANEL 237 Engine Temperature Warning Light Red Warning What It Means Light Engine Temperature Warning Light This light warns of an overheated engine condition. As engine coolant temperatures rise and the gauge approaches H, this indicator will illuminate and a single chime will sound after reaching a set threshold.
Page 240
238 UNDERSTANDING YOUR INSTRUMENT PANEL Battery Charge Warning Light Red Telltale What It Means Light Battery Charge Warning Light This light illuminates when the battery is not charging properly. If it stays on while the en- gine is running, there may be a malfunction with the charging system. Contact your autho- rized dealer as soon as possible.
Page 241
UNDERSTANDING YOUR INSTRUMENT PANEL 239 Oil Pressure Warning Light Red Telltale What It Means Light Oil Pressure Warning Light This light indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on.
Page 242
240 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Throttle Control (ETC) Warning Light Red Telltale What It Means Light Electronic Throttle Control (ETC) Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected while the engine is running, the light will either stay on or flash de- pending on the nature of the problem.
Page 243
UNDERSTANDING YOUR INSTRUMENT PANEL 241 Transmission Temperature Warning Light Red Telltale What It Means Light Transmission Temperature Warning Light This light indicates that the transmission fluid temperature is running hot. This may occur with severe usage. If this light turns on, safely pull over and stop the vehicle. Then, place the transmission into NEUTRAL and run the engine at idle speed or apply light foot pressure to increase the engine speed RPM until the Transmission Temperature light turns off.
Page 244
242 UNDERSTANDING YOUR INSTRUMENT PANEL Electric Power Steering Fail Warning — If Equipped Red Telltale What It Means Light Electric Power Steering Fail Warning — If Equipped This light is used to manage the electrical warning of the EPS (Power Steering System). Refer to “Power Steering”...
Page 245
UNDERSTANDING YOUR INSTRUMENT PANEL 243 Trunk Open Warning Light Red Telltale What It Means Light Trunk Open Warning Light This indicator will illuminate when the trunk is open and not fully closed. NOTE: If the vehicle is moving there will also be a single chime.
244 UNDERSTANDING YOUR INSTRUMENT PANEL Yellow Telltale Indicator Lights Engine Check/Malfunction Indicator Light (MIL) Yellow Telltale What It Means Light Engine Check/Malfunction Indicator Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems. The light will illuminate when the ignition is in the ON position before engine start.
Page 247
UNDERSTANDING YOUR INSTRUMENT PANEL 245 WARNING! CAUTION! A malfunctioning catalytic converter, as referenced Prolonged driving with the Malfunction Indicator above, can reach higher temperatures than in normal Light (MIL) on could cause damage to the engine operating conditions. This can cause a fire if you control system.
Page 248
246 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Stability Control (ESC) Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) Indicator Light — If Equipped The “ESC Indicator Light” in the instrument cluster will come on when the ignition is placed in the ON/RUN position, and when ESC is activated.
Page 249
UNDERSTANDING YOUR INSTRUMENT PANEL 247 Electronic Stability Control (ESC) OFF Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) OFF Indicator Light — If Equipped This light indicates the Electronic Stability Control (ESC) is off. Low Washer Fluid Indicator Light —...
Page 250
248 UNDERSTANDING YOUR INSTRUMENT PANEL Tire Pressure Monitoring Indicator Light Yellow Telltale What It Means Light Tire Pressure Monitoring Indicator Light The warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed.
Page 251
UNDERSTANDING YOUR INSTRUMENT PANEL 249 one or more of your tires is significantly under-inflated. Your vehicle has also been equipped with a TPMS Accordingly, when the low tire pressure telltale illumi- malfunction indicator to indicate when the system is not nates, you should stop and check your tires as soon as operating properly.
Page 252
250 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! CAUTION! (Continued) type, and/or style. Aftermarket wheels can cause The TPMS has been optimized for the original sensor damage. Using aftermarket tire sealants may equipment tires and wheels. TPMS pressures and cause the Tire Pressure Monitoring System (TPMS) warning have been established for the tire size sensor to become inoperable.
Page 253
UNDERSTANDING YOUR INSTRUMENT PANEL 251 Anti-Lock Brake (ABS) Indicator Light Yellow Telltale What It Means Light Anti-Lock Brake (ABS) Indicator Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition is placed in the ON/RUN position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required.
Page 254
252 UNDERSTANDING YOUR INSTRUMENT PANEL Low Fuel Indicator Light Yellow Telltale What It Means Light Low Fuel Indicator Light When the fuel level reaches approximately 2 gal (7.5 L) this light will turn on, and remain on until fuel is added. Adaptive Cruise Control Fault Indicator Light —...
Page 255
UNDERSTANDING YOUR INSTRUMENT PANEL 253 Service Forward Collision Warning Indicator Light — If Equipped Yellow Telltale What It Means Light Service Forward Collision Warning Indicator Light — If Equipped This telltale will turn on when there is a fault in the Forward Collision Warning system. Contact your authorized dealership.
254 UNDERSTANDING YOUR INSTRUMENT PANEL Green Telltale Indicator Lights Front Fog Indicator Light — If Equipped Green Telltale What It Means Light Front Fog Indicator Light — If Equipped This indicator will illuminate when the front fog lights are on. Park/Headlight ON Indicator Light Green Telltale What It Means...
Page 257
UNDERSTANDING YOUR INSTRUMENT PANEL 255 ECO Mode Indicator Light Green Telltale Light What It Means ECO Mode Indicator Light This light will turn on when ECO Mode is active. Turn Signal Indicator Lights Green Telltale What It Means Light Turn Signal Indicator Lights The instrument cluster directional arrow will flash independently for the LEFT or RIGHT turn signal as selected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multifunction lever is moved down (LEFT) or up (RIGHT).
256 UNDERSTANDING YOUR INSTRUMENT PANEL Cruise Control Engaged Indicator Light — If Equipped Green Telltale What It Means Light Cruise Control Engaged Indicator Light This light will turn on when the cruise control has been set to a certain speed. Blue Telltale Indicator Lights High Beam Indicator Light Blue Telltale...
UNDERSTANDING YOUR INSTRUMENT PANEL 257 White Telltale Indicator Lights Cruise Control Ready Indicator Light White Telltale What It Means Light Cruise Control Ready Indicator Light This light will turn on when the electronic speed control is ON, but not set. Sport Mode Indicator Light White Telltale What It Means...
Page 260
258 UNDERSTANDING YOUR INSTRUMENT PANEL Track Mode Indicator Light White Telltale What It Means Light Track Mode Indicator Light This light will turn on when Track Mode is active. Refer to “Drive Modes” in “Starting And Operating” for further information. Custom Mode Indicator Light White Telltale What It Means...
Page 261
UNDERSTANDING YOUR INSTRUMENT PANEL 259 Valet Mode Indicator Light White Telltale What It Means Light Valet Mode Indicator Light This light will turn on when Valet Mode is active. Refer to “Drive Modes” in “Starting And Operating” for further information.
260 UNDERSTANDING YOUR INSTRUMENT PANEL DRIVER INFORMATION DISPLAY (DID) This system conveniently allows the driver to select a variety of useful information by pushing the arrow The Driver Information Display (DID) features an inter- buttons located on the left side of the steering wheel. The active display which is located in the instrument cluster.
Page 263
UNDERSTANDING YOUR INSTRUMENT PANEL 261 The system allows the driver to select information by UP And DOWN Arrow Buttons: pushing the following buttons mounted on the steering Using the UP or DOWN arrows allows you to wheel: cycle through the Main Menu Items. Changes the Main Screen area and Menu Title area.
262 UNDERSTANDING YOUR INSTRUMENT PANEL • Main menu and submenu’s wrap for continuous • Pushing the LEFT arrow button will exit each scrolling. submenu layer and return to the main menu. • Upon returning to a main menu, the last submenu For the Trip and Fuel Economy menus (and new Perfor- screen viewed within that main menu will be displayed.
Page 265
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Unless reset, this message will continue to display each Use the steering wheel DID controls for the following time you place the ignition in the ON/RUN position. To procedure(s): turn off the message temporarily, push and release the 1.
264 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Push and release the UP or DOWN arrow Performance Shift Indicator (PSI) – If Equipped button to exit the submenu screen. The Performance Shift Indicator (PSI) is enabled on NOTE: If the indicator message illuminates when you vehicles with manual transmission, or when a vehicle start the vehicle, the oil change indicator system did not with automatic transmission is in manual shift mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 NOTE: Refer to “Uconnect Settings” in “Understanding DID Selectable Menu Items Your Instrument Panel” for further information on en- Push and release the UP or DOWN arrow button abling, disabling, and configuring the Performance Shift until the desired Selectable Menu item is displayed in Indicator.
Page 268
266 UNDERSTANDING YOUR INSTRUMENT PANEL directional prompts to access or reset any of the Boost Pressure — 6.2L Supercharged following Vehicle Info submenu items: Intercooler Water Temp — 6.2L Supercharged Tire Pressure Monitor Performance Features — If Equipped Coolant Temp WARNING! Trans Temp Measurement of vehicle statistics with the Perfor-...
Page 269
UNDERSTANDING YOUR INSTRUMENT PANEL 267 • 1/8 Mile (200 meters) Timer Push an release the UP or DOWN arrow button until the Performance menu is displayed in the DID. – Best Push the RIGHT arrow button to enter the – Last submenus.
Page 270
268 UNDERSTANDING YOUR INSTRUMENT PANEL • Lap Timer • To clear the vehicle’s best, last, and current 0-60 MPH (0-100 km/h) time, push and hold the OK button for • Lap History two seconds. – Will list the last 5 laps with the best lap highlighted 0 to 100 MPH (0 to 161 km/h) in green.
Page 271
UNDERSTANDING YOUR INSTRUMENT PANEL 269 • Dashes will display if the vehicle fails to reach 1/8 Reaction Timer mile (200 meters) in less then 15 seconds. Press the OK button to engage Countdown Timer. The • To clear the vehicle’s best 1/8 mile (200 meters) run, time it takes for the wheel speed to not equal 0 MPH, after the word GO, is your reaction time.
Page 272
270 UNDERSTANDING YOUR INSTRUMENT PANEL Braking Distance Current G-Force When selected, this screen displays the vehicle’s braking When selected, this screen displays the current G-Force distance, and the speed at which the brake pedal was (lateral and longitudinal) that displays the directions of pushed.
Page 273
UNDERSTANDING YOUR INSTRUMENT PANEL 271 • Pushing the OK button will start “current” timer from • The timer will stop when the driver navigates away 0:00.0. from this page. • When the OK button is pushed, the times are updated Lap History accordingly.
Page 274
272 UNDERSTANDING YOUR INSTRUMENT PANEL Top Speed Adaptive Cruise Control Off When selected, this screen displays the Top Speed since When ACC is deactivated, the display will read “Adap- last reset: tive Cruise Control Off.” • Populates a top speed from first drive cycle and every Adaptive Cruise Control Ready time that speed is exceeded that number is stored here When ACC is activated but the vehicle speed setting has...
Page 275
UNDERSTANDING YOUR INSTRUMENT PANEL 273 • System Cancel • Current Fuel Economy (MPG, L/100 km, or km/l) • Driver Override • Range To Empty (miles or km) • System Off • Average Fuel Economy (MPG, L/100 km, or km/l) • ACC Proximity Warning •...
Page 276
274 UNDERSTANDING YOUR INSTRUMENT PANEL • Average Fuel Economy – Shows the average fuel and release the OK button to enter the submenus. The economy (MPG, L/100 or km/l) of Trip A or Trip B Screen Setup feature allows you to change what since the last reset.
Page 277
UNDERSTANDING YOUR INSTRUMENT PANEL 275 • Time • Trip B Distance • Range to Empty • Audio Inform • Average L/100km (or MPG) • Digital Speed • Current L/100km (or MPG) • None • Trip A Distance 4. Current Gear •...
276 UNDERSTANDING YOUR INSTRUMENT PANEL • If the menu is exited before the end of codes is reached Diagnostics — If Equipped - when the driver re-enters the list will be restarted This feature allows the driver to view engine and emis- from the beginning.
Page 279
UNDERSTANDING YOUR INSTRUMENT PANEL 277 Load reduction is only active when the engine is running. “Battery Charge Warning Light” in “Understanding It will display a message if there is a risk of battery Your Instrument Panel” for further information. depletion to the point where the vehicle may stall due to The electrical loads that may be switched off (if lack of electrical supply, or will not restart after the equipped), and vehicle functions which can be effected...
Page 280
278 UNDERSTANDING YOUR INSTRUMENT PANEL • The battery was discharged by an electrical load left on loads are larger than the capability of charging system. The charging system is still functioning properly. when the vehicle was parked. • Turning on all possible vehicle electrical loads (e.g. •...
UNDERSTANDING YOUR INSTRUMENT PANEL 279 After a trip: Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful • Check if any aftermarket equipment was installed access to vehicle systems and wireless communications. (additional lights, upfitter electrical accessories, audio Vehicle software technology continues to evolve over systems, alarms) and review specifications if any (load...
Page 282
280 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: WARNING! • FCA or your dealer may contact you directly regarding • It is not possible to know or to predict all of the software updates. possible outcomes if your vehicle’s systems are • To help further improve vehicle security and minimize breached.
UNDERSTANDING YOUR INSTRUMENT PANEL 281 Privacy of any wireless and wired communications can- not be assured. Third parties may unlawfully intercept information and private communications without your consent. For further information, refer to “Privacy Prac- tices – If Equipped with Uconnect 8.4 radio” in “All About Uconnect Access”...
282 UNDERSTANDING YOUR INSTRUMENT PANEL Buttons On The Faceplate Buttons On The Touchscreen Buttons on the faceplate are located below the Uconnect Buttons on the touchscreen are accessible on the system in the center of the instrument panel. In addition, Uconnect display.
Page 285
UNDERSTANDING YOUR INSTRUMENT PANEL 283 NOTE: Display • Only one touchscreen area may be selected at a time. After pressing the “Display” button on the touchscreen, the following settings will be available: • Depending on the vehicles options, feature settings •...
Page 286
284 UNDERSTANDING YOUR INSTRUMENT PANEL • Display Brightness With Headlights OFF nomenclature, including the trip functions and the navi- gation system (if equipped). Press the “Set Language” When in this display, you may select the brightness with button on the touchscreen, and then press the desired the headlights off.
Page 287
UNDERSTANDING YOUR INSTRUMENT PANEL 285 • Speed Time-Out” button on the touchscreen until a check-mark appears next to the setting, showing that setting has been Select from: “MPH” or “km/h.” selected. • Distance • Navigation Turn-By-Turn In Cluster — If Equipped Select from: “mi”...
Page 288
286 UNDERSTANDING YOUR INSTRUMENT PANEL • Torque Clock Select from: “lb-ft” or “Nm.” After pressing the “Clock” button on the touchscreen the following settings will be available: Voice • Sync Time With GPS — If Equipped After pressing the “Voice” button on the touchscreen the following settings will be available: This feature will allow you to automatically have the radio set the time.
Page 289
UNDERSTANDING YOUR INSTRUMENT PANEL 287 • Set Time Minutes Safety & Driving Assistance After pressing the “Safety & Driving Assistance” button This feature will allow you to adjust the minutes. The on the touchscreen the following settings will be avail- “Sync time with GPS”...
Page 290
288 UNDERSTANDING YOUR INSTRUMENT PANEL • Rear ParkSense Volume — If Equipped button. For further information, refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features The Rear ParkSense Chime Volume settings can be se- Of Your Vehicle”. lected from the DID or Uconnect System. The chime •...
Page 291
UNDERSTANDING YOUR INSTRUMENT PANEL 289 When “Lights & Chime” mode is activated, the Blind The image will be displayed on the radio touchscreen Spot Monitor (BSM) will show a visual alert in the display along with a caution note to “check entire sur- exterior mirrors as well as an audible alert when the turn roundings”...
Page 292
290 UNDERSTANDING YOUR INSTRUMENT PANEL To set the ParkView Backup Camera Delay press the and operating information. To make your selection, press “Controls” button on the touchscreen, the “settings” the “Hill Start Assist” button on the touchscreen, until a button on the touchscreen, then the “Safety & Driving check-mark appears next to setting, indicating that the Assistance”...
Page 293
UNDERSTANDING YOUR INSTRUMENT PANEL 291 • Headlight Illumination On Approach • Auto Dim High Beams — If Equipped When this feature is selected, the headlights will activate When this feature is selected, the high beam headlights and remain on for 0, 30, 60 or 90 seconds when the doors will activate/deactivate automatically under certain con- are unlocked with the key fob.
Page 294
292 UNDERSTANDING YOUR INSTRUMENT PANEL • Flash Lights With Lock button on the touchscreen, until a check-mark appears next to the setting, showing that the setting has been When this feature is selected, the hazard lights will flash selected. when the doors are locked or unlocked with the key fob, •...
Page 295
UNDERSTANDING YOUR INSTRUMENT PANEL 293 Press” button on the touchscreen, until a check-mark NOTE: If the vehicle is programmed 1st Press Of Key Fob appears next to setting, showing that setting has been Unlocks “All Doors,” all doors will unlock no matter selected.
Page 296
294 UNDERSTANDING YOUR INSTRUMENT PANEL has been selected. Refer to “Keyless Enter-N-Go” in Auto Comfort Systems — If Equipped “Things To Know Before Starting Your Vehicle”. After pressing the “Auto-On Comfort” button on the • Personal Settings Linked To Key Fob — If Equipped touchscreen the following settings will be available: •...
Page 297
UNDERSTANDING YOUR INSTRUMENT PANEL 295 Engine Off Options button on the touchscreen to select your desired time interval, and choose from “0 seconds,” “45 seconds,” After pressing the “Engine Off Options” button on the “5 minutes” or “10 minutes.” touchscreen the following settings will be available: •...
Page 298
296 UNDERSTANDING YOUR INSTRUMENT PANEL • Equalizer • AUX Volume Offset — If Equipped This feature allows you to adjust the Bass, Mid and Treble This feature provides the ability to tune the audio level settings. Adjust the settings with the “+” and “–” setting for portable devices connected through the AUX input.
Page 299
UNDERSTANDING YOUR INSTRUMENT PANEL 297 • Paired Phones • Subscription Information This feature shows which phones are paired to the New vehicle purchasers or lessees will receive a free Phone/Bluetooth system. For further information, refer limited time subscription to SiriusXM Satellite Radio to the Uconnect Owner’s Manual Supplement.
Page 300
298 UNDERSTANDING YOUR INSTRUMENT PANEL • Clear Personal Data Restore Settings After pressing the “Restore Settings” button on the When this feature is selected it will remove all personal touchscreen the following settings will be available: data including Bluetooth devices and presets. To remove personal information, press the “Clear Personal Data”...
UNDERSTANDING YOUR INSTRUMENT PANEL 299 SRT PERFORMANCE PAGES WARNING! Performance Pages is an application that provides a Measurement of vehicle statistics with the SRT Per- display for performance indicators, as received from the formance Pages is intended for off-highway or off- Instrument Cluster, that will help you gain familiarity road use only and should not be done on any public with the capabilities of your SRT vehicle in real-time.
300 UNDERSTANDING YOUR INSTRUMENT PANEL The Performance Pages include the following: The following describes each feature and its operation: • Home Home • Timers • Gauges 1 • Gauges 2 • G-Force • Engine SRT Performance Pages — Home...
UNDERSTANDING YOUR INSTRUMENT PANEL 301 When Home is selected, the following features will be Timers available: • A series of six images which can be selected by the user. • A left and right arrow to allow the user to scroll through vehicle images.
Page 304
302 UNDERSTANDING YOUR INSTRUMENT PANEL When the Timers Page is selected you will be able to over 10, will overwrite the oldest saved run for Uconnect select from following “Tickets”: System storage. The operation of the Save feature is listed below: •...
Page 305
UNDERSTANDING YOUR INSTRUMENT PANEL 303 • With an SD Card installed, press the “SD Card” to save • The Reaction Time, MPH, ⅛, and ¼ Mile timers will be runs to the SD Card. “ready” when the vehicle is at 0 MPH (0 km/h). •...
304 UNDERSTANDING YOUR INSTRUMENT PANEL • Brake Distance Gauges 1 Displays the distance it takes the vehicle to make a full stop. Contains current and last data for distance and start – from speed. NOTE: The distance measurement will be aborted if the brake pedal is released before the vehicle comes to a complete stop.
Page 307
UNDERSTANDING YOUR INSTRUMENT PANEL 305 • Oil Pressure Shows the actual oil pressure. • Oil Temperature Shows the actual oil temperature. • Battery Voltage Shows the actual battery voltage. • Trans Oil Temp (Auto Transmission Only) Shows the actual automatic transmission oil temperature. SRT Performance Pages —...
306 UNDERSTANDING YOUR INSTRUMENT PANEL • Oil Pressure Shows the actual oil pressure. Gauges 2 SRT Performance Pages — Gauges 1 (6.4L) When selected, this screen displays the following values: • Coolant Temperature Shows the actual coolant temperature. • Oil Temperature SRT Performance Pages —...
Page 309
UNDERSTANDING YOUR INSTRUMENT PANEL 307 • Intake Air Temperature Shows the actual intake air temperature. • Transmission Temperature (Automatic Transmission Only) Shows the actual transmission temperature. SRT Performance Pages — Gauges 2 (6.4L Automatic Transmission) When selected, this screen displays the following values: •...
308 UNDERSTANDING YOUR INSTRUMENT PANEL When selected, this screen displays the following values: G-Force • Boost Pressure Shows the current value for boost pressure. • Air Fuel Ratio Shows the current value for the air fuel ratio. • Inter-Cooler (I/C) Coolant Temperature Shows the current value for the I/C coolant temperature.
Page 311
UNDERSTANDING YOUR INSTRUMENT PANEL 309 • Vehicle Speed When G-Force is selected, the following features will be available: Vehicle Speed measures the current speed of the vehicle • Lateral G-Force Left and Right in either mph or km/h, starting at 0 with no maximum value.
UNDERSTANDING YOUR INSTRUMENT PANEL 311 • Instantaneous Horsepower/Kilowatts SRT DRIVE MODES Key FOB 6.2L Supercharged Engine — If Equipped Shows the instantaneous horsepower. • Instantaneous Torque Shows the instantaneous torque. • Oil Pressure (6.4L Only) Shows the actual oil pressure. •...
Page 314
312 UNDERSTANDING YOUR INSTRUMENT PANEL RED key FOB unlocks the full potential of the engine’s the SRT Drive Modes interface, and can be accessed by output, and allows the driver to select from two power pressing the “KEY FOB” button on the touchscreen in the levels within Drive Modes Set-Up.
Page 315
UNDERSTANDING YOUR INSTRUMENT PANEL 313 • Selecting “Drive Modes” from the “Apps” menu. Your SRT vehicle is equipped with a Drive Modes feature which allows for coordinating the operation of various • Selecting “Drive Modes” from within the Performance vehicle systems depending upon the type of driving Pages menu.
314 UNDERSTANDING YOUR INSTRUMENT PANEL The SRT Drive Modes main screen displays the current Listed below are the available Drive Modes: drive mode and real-time status of the vehicle’s perfor- Track Mode mance configuration. The selectable Drive Modes buttons are Track, Sport, Custom, or Default and will be high- lighted when displaying the current configuration.
UNDERSTANDING YOUR INSTRUMENT PANEL 315 Pressing the “Track” button on the touchscreen will Sport Mode activate the configuration for typical track driving. The Transmission, Traction, Steering, and Suspension systems are all set to their “Track” settings highlighted in red. The Paddle Shifters are enabled.
316 UNDERSTANDING YOUR INSTRUMENT PANEL Default Mode This mode is for typical driving conditions where the Traction and Transmission will be operating in their Street settings, which cannot be changed while in this mode. The Steering and Suspension can be configured in either the “Street,”...
UNDERSTANDING YOUR INSTRUMENT PANEL 317 Custom Mode configuration that is saved for quick selection of your favorite settings. While in Custom Mode, the Power, Traction, Transmission, Steering, Suspension, and Paddle Shifter settings are shown in their current configuration. Custom Mode The Custom Mode may be selected quickly by pushing Custom Mode Set-Up —...
Page 320
318 UNDERSTANDING YOUR INSTRUMENT PANEL While in the Custom Drive Mode screen, press the Power — If Equipped With 6.2L Supercharged “Custom Set-Up” button on the touchscreen to access the Engine selectable options. In the Custom Mode Set-Up screen the individual current configuration will be displayed.
Page 321
UNDERSTANDING YOUR INSTRUMENT PANEL 319 • 700+ Transmission Press the “700+” button on the touchscreen to modify the output power of the engine to 700+. NOTE: This selection is only available with the RED key fob. • 500 Press the “500” button on the touchscreen to modify the output power of the engine to 500.
Page 322
320 UNDERSTANDING YOUR INSTRUMENT PANEL • Sport Paddle Shifters – If Equipped With Automatic Transmission Press the “Sport” button on the touchscreen to provide faster shift speeds and will have a moderate comfort trade-off. • Street Press the “Street” button on the touchscreen to provide a balance of shift speed and comfort for typical daily driving.
Page 323
UNDERSTANDING YOUR INSTRUMENT PANEL 321 • ON Traction Press the “ON” button on the touchscreen to enable steering wheel paddle shifters. • OFF Press the “OFF” button on the touchscreen to disable steering wheel paddle shifters. Traction • Track Press the “Track” button on the touchscreen to modify traction control to optimize track performance with the least stability control.
Page 324
322 UNDERSTANDING YOUR INSTRUMENT PANEL • Sport Suspension Press the “Sport” button on the touchscreen to turn off traction control and reduce stability control. • Street Press the “Street” button on the touchscreen to provide full traction control and full stability control. Suspension...
Page 325
UNDERSTANDING YOUR INSTRUMENT PANEL 323 • Track Steering — If Equipped With 6.4L Engine Press the “Track” button on the touchscreen to provide the firmest possible suspension stiffness with the highest amount of comfort trade-off. • Sport Press the “Sport” button on the touchscreen to provide a firmer suspension stiffness with moderate comfort trade- off.
324 UNDERSTANDING YOUR INSTRUMENT PANEL • Sport RACE OPTIONS Press the “Sport” button on the touchscreen to adjust the steering effort to the higher level. • Street Press the “Street button on the touchscreen to adjust the steering effort to the lowest level. Race Options Press the “Race Options”...
UNDERSTANDING YOUR INSTRUMENT PANEL 325 Launch Control WARNING! Launch Mode is intended for off-highway or off-road use only and should not be used on any public roadways. It is recommended that this feature be used in a controlled environment, and within the limits of the law.
Page 328
326 UNDERSTANDING YOUR INSTRUMENT PANEL “Launch RPM Set-Up” to set the holding RPM. Launch Mode can be turned on or off by either pushing the Launch Control button on the instrument panel switch bank (if activated), or by pressing the “Cancel Launch Mode”...
UNDERSTANDING YOUR INSTRUMENT PANEL 327 Shift Light within the Driver Information Display (DID). This fea- ture is a visual cue to manually up-shift using the paddle shifters or the transmission gear selector in manual shift mode. To actuate the Shift Light feature, press the “Shift Light” button on the touchscreen, then press the “Shift Light On”...
Page 330
328 UNDERSTANDING YOUR INSTRUMENT PANEL transmission) 1, 2, 3, 4, and 5-6 (manual transmission). Pressing and releasing the up/down arrow buttons on the touchscreen above and below each listed gear, the RPM values will change in increments of 250 RPM. Pressing and holding the arrows will change the RPM values in increments of 500 RPM, ranging from 2000–...
UNDERSTANDING YOUR INSTRUMENT PANEL 329 VALET MODE not set, so you are free to select any 4 digit numeric combination that will be easy to remember. While in Valet Mode, the following vehicle configura- tions are set and locked to prevent unauthorized modi- fication: •...
Page 332
330 UNDERSTANDING YOUR INSTRUMENT PANEL • The Launch Control button is disabled. be accessed by either pushing the SRT button on the faceplate, or pressing the “Valet Mode Active – Press • Engine power is reduced. Here to Exit” button on the touchscreen. Valet Mode Deactivation Valet Mode Deactivation PIN To exit Valet Mode, you must enter the same 4 digit PIN...
UNDERSTANDING YOUR INSTRUMENT PANEL 331 press the “OK” button on the touchscreen. Your vehicle ECO MODE — IF EQUIPPED WITH AUTOMATIC will return to the default state whenever exiting Valet TRANSMISSION Mode. NOTE: If your 4 digit PIN is lost or forgotten, the vehicle will exit Valet Mode after a battery disconnect for ap- proximately five minutes.
332 UNDERSTANDING YOUR INSTRUMENT PANEL performance. Increased engine exhaust noise and/or Located in the front storage area of the center console, vibration may be noticed while Eco is active. This is this feature allows an iPod/MP3 player, or an external normal and a result of the increased amount of operating USB device, to be connected to the audio system.
UNDERSTANDING YOUR INSTRUMENT PANEL 333 iPod control supports Mini, 4G, Photo, Nano, 5G iPod and iPhone devices. Some iPod software versions may not fully support the iPod control features. Please visit Apple’s website for software updates. For further information, refer to the Uconnect User’s Manual.
334 UNDERSTANDING YOUR INSTRUMENT PANEL Pushing the center button will make the radio switch Media Mode between the various modes available (AM/FM/AUX Pushing the top of the switch once will go to the next etc.). track on the selected media (AUX, Bluetooth, SD Card). Pushing the bottom of the switch once will go to the The left-hand control is a rocker-type switch with a beginning of the current track, or to the beginning of the...
UNDERSTANDING YOUR INSTRUMENT PANEL 335 antenna, it is recommended that the radio volume be The radio manufacturer believes the internal wireless turned down or off during mobile device operation when radio is safe for use by consumers. The level of energy not using Uconnect (if equipped).
336 UNDERSTANDING YOUR INSTRUMENT PANEL • Increase the separation between the equipment and NOTE: receiver. • This equipment has been tested and found to comply • Consult the dealer or an experienced radio technician with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
UNDERSTANDING YOUR INSTRUMENT PANEL 337 General Overview Buttons On The Touchscreen Buttons On The Faceplate Buttons on the touchscreen are accessible on the Uconnect system screen. The buttons on the faceplate are located below the Uconnect screen. Uconnect 8.4 Automatic Temperature Controls — Buttons On The Touchscreen Automatic Climate Controls —...
Page 340
338 UNDERSTANDING YOUR INSTRUMENT PANEL Button Descriptions (Applies To Both Buttons On The 4. AUTO Operation Button Faceplate And Buttons On The Touchscreen) Automatically controls the interior cabin temperature by 1. MAX A/C Button adjusting airflow distribution and amount. Performing this function will cause the system to switch between Press and release to change the current setting, the manual mode and automatic modes.
Page 341
UNDERSTANDING YOUR INSTRUMENT PANEL 339 6. Rear Defrost Button CAUTION! (Continued) Press and release this button to turn on the rear window • Do not use scrapers, sharp instruments, or abrasive defroster and the heated outside mirrors (if equipped). window cleaners on the interior surface of the An indicator will illuminate when the rear window window.
Page 342
340 UNDERSTANDING YOUR INSTRUMENT PANEL 8. Passenger Temperature Control Down Button 10. Blower Control (Uconnect 8.4 Radio Only) Blower control is used to regulate the amount of air Provides the passenger with independent temperature forced through the climate system. There are seven control.
Page 343
UNDERSTANDING YOUR INSTRUMENT PANEL 341 • Bi-Level Mode Button On The Touchscreen Air comes from the instrument panel outlets Use the small blower icon to reduce the blower setting and floor outlets. A slight amount of air is and the large blower icon to increase the blower setting. directed through the defrost and side window demis- Blower can also be selected by pressing the blower bar ter outlets.
342 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Climate Control OFF Button 14. Driver Temperature Control Up Button (Uconnect 8.4 Only) Press and release this button to turn the Climate Control ON/OFF. Provides the driver with independent temperature con- trol. Push the button on the faceplate for warmer tem- 13.
Page 345
UNDERSTANDING YOUR INSTRUMENT PANEL 343 button to turn off the air conditioning and manually front fascia protectors may reduce airflow to the adjust the blower and airflow mode settings. Also, make condenser, reducing air conditioning performance. sure to select only Panel, Bi-Level or Floor modes. MAX A/C NOTE: MAX A/C sets the control for maximum cooling perfor-...
344 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation mode will cause the LED in the control button to blink and then turn off. When outside air contains smoke, odors, or Automatic Temperature Control (ATC) high humidity, or if rapid cooling is desired, Automatic Operation you may wish to recirculate interior air by pressing the Recirculation control button.
Page 347
UNDERSTANDING YOUR INSTRUMENT PANEL 345 NOTE: Manual Operation Override • It is not necessary to move the temperature settings. The system allows for manual selection of blower speed, air distribution mode, A/C status and recirculation control. The system automatically adjusts the temperature, mode, and blower speed to provide comfort as quickly The blower fan speed can be set to any fixed speed by as possible.
346 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Winter Operation Use of the air Recirculation mode during winter months is NOTE: Refer to the chart at the end of this section for not recommended because it may cause window fogging. suggested control settings for various weather condi- tions.
Page 349
UNDERSTANDING YOUR INSTRUMENT PANEL 347 windshield and provide sufficient heating. If side win- Outside Air Intake dow fogging becomes objectionable, increase blower Make sure the air intake, located directly in front of the speed to improve airflow and clearing of the side win- windshield, is free of obstructions such as leaves.
Page 350
348 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions For Various Weather Conditions...
UNDERSTANDING YOUR INSTRUMENT PANEL 349 PERSONALIZED MENU BAR 2. Press and hold, then drag the selected App to replace an existing shortcut in the main menu bar. The Uconnect features and services in the main menu bar The replaced shortcut will now be an active App/ are easily changed for your convenience.
350 UNDERSTANDING YOUR INSTRUMENT PANEL Get Started All you need to control your Uconnect system with your voice are the buttons on your steering wheel. 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing in- structions.
Page 353
UNDERSTANDING YOUR INSTRUMENT PANEL 351 4. Each time you give a Voice Command, you must first push either the VR or Phone button, wait until after the beep, then say your Voice Command. 5. You can interrupt the help message or system prompts by pushing the VR or Phone button and saying a Voice Command from current category.
352 UNDERSTANDING YOUR INSTRUMENT PANEL Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect system. Push the VR button . After the beep, say • Cancel to stop a current voice session •...
UNDERSTANDING YOUR INSTRUMENT PANEL 353 Radio Use your voice to quickly get to the AM, FM or SiriusXM Satellite Radio stations you would like to hear. (Subscrip- tion or included SiriusXM Satellite Radio trial required.) Push the VR button . After the beep, say •...
Page 356
354 UNDERSTANDING YOUR INSTRUMENT PANEL Push the VR button . After the beep, say one of the following commands and follow the prompts to switch your media source or choose an artist. • Change source to Bluetooth • Change source to AUX •...
UNDERSTANDING YOUR INSTRUMENT PANEL 355 Phone TIP: When providing a Voice Command, push the Phone button and say “Call,” then pronounce the name Making and answering hands-free phone calls is easy exactly as it appears in your phone book. When a with Uconnect.
356 UNDERSTANDING YOUR INSTRUMENT PANEL Voice Text Reply PRE-DEFINED VOICE TEXT REPLY RESPONSES Uconnect will announce incoming text messages. Push Yes. Stuck in traffic. See you later. the Phone button and say Listen. (Must have com- Start without I’ll be late. patible mobile phone paired to Uconnect system.) 1.
Page 359
UNDERSTANDING YOUR INSTRUMENT PANEL 357 TIP: Your mobile phone must have the full implementa- tion of the Message Access Profile (MAP) to take advan- tage of this feature. For details about MAP, visit UconnectPhone.com. Apple iPhone iOS 6 or later supports reading incoming text messages only.
358 UNDERSTANDING YOUR INSTRUMENT PANEL TIP: Voice Text Reply is not compatible with iPhone, but TIP: Voice Command for Climate may only be used to if your vehicle is equipped with Siri Eyes Free, you can adjust the interior temperature of your vehicle. Voice use your voice to send a text message.
UNDERSTANDING YOUR INSTRUMENT PANEL 359 Navigation (8.4A/8.4AN) TIP: To start a POI search, push the VR button . After the beep, say: “ Find nearest coffee shop.” The Uconnect navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go.
360 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect Access (8.4A/8.4AN) NOTE: Uconnect Access is available only on equipped vehicles purchased within the continental United States, Alaska and Hawaii. Services can only be used where WARNING! coverage is available; see coverage map for details. ALWAYS obey traffic laws and pay attention to the 9-1-1 Call road.
UNDERSTANDING YOUR INSTRUMENT PANEL 361 Vehicle Health Alert Your vehicle will send you an email alert if it senses a problem under the hood with one of your vehicles key systems. For further information go to the Mopar Owner Connect website moparownerconnect.com. Register (8.4A/8.4AN) To unlock the full potential of Uconnect Access in your vehicle, you first need to register with Uconnect Access.
362 UNDERSTANDING YOUR INSTRUMENT PANEL Signing up is easy! Simply follow the steps above. Or, press the “Apps ” button on the touchscreen to “Register By Web” to complete the process using your smartphone or computer. For further information, please visit DriveUconnect.com. Mobile App (8.4A/8.4AN) You’re only a few steps away from using remote com- mands and playing your favorite music in your vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 363 3. Press the app you’d like to connect to your vehicle. Voice Texting (8.4A/8.4AN) 4. Enter your login information for the selected app and 1. To send a message, push the Phone button . After press Link.
Page 366
364 UNDERSTANDING YOUR INSTRUMENT PANEL You must be registered with Uconnect Access and have a compatible MAP – enabled smartphone to use your voice to send a personalized text message. For details about MAP, visit UconnectPhone.com. Apple iPhone iOS6 or later supports reading incoming text messages only.
UNDERSTANDING YOUR INSTRUMENT PANEL 365 TIP: 2. Press the “Yelp” button on the touchscreen. • Voice Texting is not compatible with iPhone, but if 3. Once the YELP home screen appears on the touch- your vehicle is equipped with Siri Eyes Free, you can screen, push the VR button , then say: “YELP use your voice to send a text message.
366 UNDERSTANDING YOUR INSTRUMENT PANEL TIP: Once you perform a search, you can reorganize the SiriusXM Travel Link (8.4A/8.4AN) results by selecting either the Best Match, Rating or Need to find a gas station, view local movie listings, Distance tab on the top of the touchscreen display. check a sports score or the 5 - day weather forecast? SiriusXM Travel Link is a suite of services that brings a wealth of information right to your Uconnect 8.4AN...
UNDERSTANDING YOUR INSTRUMENT PANEL 367 TIP: Traffic alerts are not accessible with Voice Com- Siri Eyes Free — If Equipped mand. If your vehicle is equipped with Siri Eyes Free, you can use your voice to send text messages, schedule meetings, set reminders, and more.
368 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic reply messages can be: General Information • “I am driving right now, I will get back to you shortly.” This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following •...
Page 373
STARTING AND OPERATING CONTENTS STARTING PROCEDURES ....376 MANUAL TRANSMISSION — IF EQUIPPED . .383 ▫ Manual Transmission — If Equipped ..376 ▫...
Page 374
372 STARTING AND OPERATING ▫ Eight-Speed Automatic Transmission — If POWER STEERING — 6.2L SUPERCHARGED Equipped ......390 ENGINE .
Page 375
STARTING AND OPERATING 373 ▫ Anti-Lock Brake Warning Light... .426 TIRES — GENERAL INFORMATION ..450 ▫ Brake Assist System (BAS) ....426 ▫...
Page 376
374 STARTING AND OPERATING ▫ Materials Added To Fuel ....470 TIRE ROTATION RECOMMENDATIONS ..460 ▫ Tire Rotation — Same Tire Size On Front And ▫...
376 STARTING AND OPERATING STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the • Do not leave the key fob in or near the vehicle inside and outside mirrors, fasten your seat belt, and if (or in a location accessible to children), and do not present, instruct all other occupants to buckle their seat leave the ignition (of a vehicle equipped with belts.
STARTING AND OPERATING 377 Automatic Transmission — If Equipped Tip Start Feature The gear selector must be in the NEUTRAL or PARK Cycle the ignition switch to START position and release position before you can start the engine. Apply the brakes it.
378 STARTING AND OPERATING Normal Starting Using The ENGINE START/STOP Button — Manual Transmission Only Using The ENGINE START/STOP Button — Automatic Transmission Only 1. Press and hold the clutch pedal while pushing and holding the ENGINE START/STOP button. 1. The transmission must be in PARK or NEUTRAL. 2.
Page 381
STARTING AND OPERATING 379 To Turn Off The Engine Using ENGINE START/ NOTE: If the ignition switch is left in the ACC or RUN STOP Button — Automatic Transmission Only (engine not running) position and the transmission is in PARK, the system will automatically time out after 30 1.
Page 382
380 STARTING AND OPERATING NOTE: Keyless Enter-N-Go Functions — With Driver’s Foot OFF The Brake Pedal/Clutch Pedal (In PARK • If the ignition switch is left in the ACC position, the Or NEUTRAL Position) system will automatically time out after 30 minutes of The Keyless Enter-N-Go feature operates similar to an inactivity and the ignition will switch to the OFF ignition switch.
STARTING AND OPERATING 381 Extreme Cold Weather (Below –22°F Or −30°C) WARNING! (Continued) To ensure reliable starting at these temperatures, use of engine has started, ignite and damage the converter an externally powered electric engine block heater (avail- and vehicle. able from your authorized dealer) is recommended.
382 STARTING AND OPERATING will engage automatically, run for 10 seconds, and then After Starting disengage. Once this occurs, release the accelerator pedal The idle speed is controlled automatically, and it will and the brake pedal, wait 10 to 15 seconds, then repeat decrease as the engine warms up.
STARTING AND OPERATING 383 WARNING! CAUTION! • Never drive with your foot resting on the clutch Remember to disconnect the engine block heater cord before driving. Damage to the 110-115 Volt pedal, or try to hold the vehicle on a hill with the electrical cord could cause electrocution.
Page 386
384 STARTING AND OPERATING NOTE: During cold weather, you may experience in- NOTE: creased effort in shifting until the transmission fluid • Your vehicle is equipped with a transmission reverse warms up. This is normal. inhibitor system. When vehicle speed is greater than 3 mph (5 km/h), the reverse inhibitor activates to help prevent shifts into REVERSE.
STARTING AND OPERATING 385 Also, this may be more noticeable when the transmis- sion is warm. This is a normal condition and is not an indication of a problem with your clutch or transmis- sion. Shifting Fully press the clutch pedal and lift your foot off the accelerator pedal before shifting gears.
386 STARTING AND OPERATING The spring will try to pull the gear selector toward third You must always use first gear (or REVERSE) when and fourth gear. Make sure you move the gear selector starting from a standing position. into second or fifth gear. If you let the gear selector move Recommended Shift Speeds in the direction of the pulling, you may end shifting from To utilize your manual transmission efficiently for fuel...
STARTING AND OPERATING 387 Earlier upshifts during cruise conditions (relatively Downshifting steady speeds) may result in increased fuel economy. To maintain a safe speed and prolong brake life, down- Higher upshift speeds may be used to obtain a desired shift to maintain a safe speed when descending a steep acceleration rate.
388 STARTING AND OPERATING AUTOMATIC TRANSMISSION WARNING! (Continued) the parking brake, turn the engine OFF, remove the WARNING! key fob from the vehicle and lock your vehicle. • It is dangerous to shift out of PARK or NEUTRAL When the ignition is in the OFF mode, the auto- if the engine speed is higher than idle speed.
STARTING AND OPERATING 389 NOTE: You must press and hold the brake pedal while WARNING! (Continued) shifting out of PARK. • Do not leave the key fob in or near the vehicle (or Key Ignition Park Interlock in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN mode.
390 STARTING AND OPERATING The brake pedal must also be pressed to shift from NEUTRAL into DRIVE or REVERSE when the vehicle is stopped or moving at low speeds. Eight-Speed Automatic Transmission — If Equipped The transmission gear range (PRNDM) is displayed both on the gear selector and in the Driver Information Display (DID).
Page 393
STARTING AND OPERATING 391 Only shift from DRIVE to PARK or REVERSE when the NOTE: If the gear selector cannot be moved to the PARK, accelerator pedal is released and the vehicle is stopped. REVERSE, or NEUTRAL position (when pushed for- Be sure to keep your foot on the brake pedal when ward) it is probably in the MANUAL (AutoStick, +/-) shifting between these gears.
Page 394
392 STARTING AND OPERATING PARK (P) WARNING! This range supplements the parking brake by locking the • Never use the PARK position of an automatic transmission. The engine can be started in this range. transmission as a substitute for the parking brake. Never attempt to use PARK while the vehicle is in Always apply the parking brake fully when parked motion.
Page 395
STARTING AND OPERATING 393 WARNING! (Continued) WARNING! (Continued) • When leaving the vehicle, always remove the key someone or something. Only shift into gear when the engine is idling normally and your foot is fob and lock your vehicle. • Never leave children alone in a vehicle, or with firmly pressing the brake pedal.
Page 396
394 STARTING AND OPERATING • With brake pedal released, verify that the gear selector CAUTION! will not move out of PARK. • Before moving the gear selector out of PARK, you REVERSE (R) must start the engine and also press the brake This range is for moving the vehicle backward.
Page 397
STARTING AND OPERATING 395 automatically upshifts through all forward gears. The WARNING! (Continued) DRIVE position provides optimum driving characteris- practices that limit your response to changing traffic tics under all normal operating conditions. or road conditions. You might lose control of the When frequent transmission shifting occurs (such as vehicle and have a collision.
Page 398
396 STARTING AND OPERATING MANUAL (M) restarted. The Malfunction Indicator Light (MIL) may be illuminated. A message in the instrument cluster will The MANUAL (M, +/-) position (beside the DRIVE inform the driver of the more serious conditions, and position) enables full manual control of transmission indicate what actions may be necessary.
STARTING AND OPERATING 397 4. Wait approximately 30 seconds. AUTOSTICK 5. Restart the engine. Steering Wheel Mounted Paddle Shifters Or Console Mounted Shifter 6. Shift into the desired gear range. If the problem is no AutoStick is a driver-interactive transmission feature longer detected, the transmission will return to normal providing manual shift control, giving you more control operation.
Page 400
398 STARTING AND OPERATING This system can also provide you with more control Operation during passing, city driving, cold slippery conditions, When the gear selector is in the DRIVE (D) position, the mountain driving, and many other situations. transmission will operate automatically, shifting between the eight available gears.
Page 401
STARTING AND OPERATING 399 • In temporary AutoStick mode (gear selector in NOTE: Tapping one of the steering wheel-mounted shift paddles (+/-), while the gear selector is in DRIVE, will DRIVE), the transmission will automatically shift up activate a temporary AutoStick mode. Tapping (-) to when maximum engine speed is reached.
Page 402
400 STARTING AND OPERATING • The transmission will automatically downshift to first • Transmission shifting will be more noticeable when gear when coming to a stop. After a stop, the driver AutoStick is engaged. should manually upshift (+) the transmission as the •...
STARTING AND OPERATING 401 DRIVE MODES Your SRT vehicle is equipped with a SRT Drive Mode feature. This feature gives the driver control over the systems in the vehicle which affect its performance, enabling the driver to tune it for desired driving sce- narios.
Page 404
402 STARTING AND OPERATING • SPORT MODE — This mode is a predefined configu- ration optimized for typical enthusiast driving. The ABS, Transmission, Steering, and Suspension systems are all set to their SPORT settings. Steering wheel mounted paddle shifters are enabled. •...
Page 405
STARTING AND OPERATING 403 • Sport — provides a faster shift speed and has a • Sport — turns off traction control and reduces stability moderate comfort trade-off. control. • Street — provides a balance of shift speed and comfort •...
Page 406
404 STARTING AND OPERATING • Sport — provides greater steering feedback, requiring • When selecting 500 HP, the vehicle will lock into greater steering effort. “Street” mode. Eco and Valet mode are still selectable. • Street — provides a balance of steering feedback and •...
Page 407
STARTING AND OPERATING 405 a four digit PIN code. The PIN code is not predeter- NOTE: mined, so the operator is free to select any four digit • To exit VALET Mode the operator must enter the same numeric combination that will be easy to remember. four digit PIN that was used to enter the mode.
406 STARTING AND OPERATING Launch Mode — If Equipped Preconditions: • Launch Mode should not be used on public roads. This vehicle is equipped with a Launch Mode system that is designed to allow the driver to achieve maximum Always check track conditions and the surrounding vehicle acceleration in a straight line.
Page 409
STARTING AND OPERATING 407 Automatic Transmission — If Equipped 5. Make sure the steering wheel is pointing straight. Launch Mode is only available when the following 6. Hold the brake and make sure the vehicle is in procedure is followed: “Drive”.
Page 410
408 STARTING AND OPERATING Launch mode will be active until the vehicle reaches Launch Mode is only available when the following 62 mph (100 km/h), at which point the ESC system will procedure is followed: return to its current ESC mode. 1.
Page 411
STARTING AND OPERATING 409 6. Fully depress the clutch pedal and make sure the 9. Keep the vehicle pointed straight. vehicle is in first gear. Launch mode will be active until the vehicle reaches 62 mph (100 km/h), at which point the ESC system will 7.
410 STARTING AND OPERATING • Prior to each track event, verify the front and rear CAUTION! brake pads have more than ½ pad thickness remain- ing. If the brake pads require changing, please burnish Do not attempt to shift when the drive wheels are prior to track outing at full pace.
Page 413
STARTING AND OPERATING 411 • All SRT vehicles are track tested for 24 hours of NOTE: It is recommended that you target 40psi (276kpa) endurance. However, it is recommended that suspen- Hot Tire Pressure at the conclusion of each track session. sion system, brake system, prop shaft, and ½...
Page 414
412 STARTING AND OPERATING 2. Lap the track in this manner until you start smelling 6. Sometimes, a second burnish session is required. If the the brakes. Continue for another ½ lap at speed, then pads start smelling in the next track session, reduce do a two lap cool down with minimal brake applies.
STARTING AND OPERATING 413 DRIVING ON SLIPPERY SURFACES Traction When driving on wet or slushy roads, it is possible for a Acceleration wedge of water to build up between the tire and road Rapid acceleration on snow covered, wet, or other slip- surface.
414 STARTING AND OPERATING Your vehicle may be equipped with a Limited Slip Flowing/Rising Water Differential (LSD) that reduces, but does not eliminate, the amount of wheel slip across a given axle for im- WARNING! proved handling. Do not drive on, or cross, a road or a path where water is flowing and/or rising (as in storm run-off).
Page 417
STARTING AND OPERATING 415 WARNING! CAUTION! (Continued) standing water that is deeper than the bottom of • Driving through standing water limits your vehi- the tire rims mounted on the vehicle. cle’s traction capabilities. Do not exceed 5 mph • Determine the condition of the road or the path (8 km/h) when driving through standing water.
416 STARTING AND OPERATING If for some reason the power assist is interrupted, it will CAUTION! (Continued) still be possible to steer your vehicle. Under these condi- damage is not covered by the New Vehicle Limited tions, you will observe a substantial increase in steering Warranty.
STARTING AND OPERATING 417 apparent, and/or the system is not functioning as antici- WARNING! pated. Coordinate inspection efforts through an autho- rized dealer. Continued operation with reduced power steering assist could pose a safety risk to yourself and others. CAUTION! Service should be obtained as soon as possible.
418 STARTING AND OPERATING If necessary, add fluid to restore to the proper indicated WARNING! level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, And Genuine Continued operation with reduced assist could pose Parts”...
STARTING AND OPERATING 419 NOTE: PARKING BRAKE • Even if the power steering assistance is no longer Before leaving the vehicle, make sure that the parking brake is fully applied and place the gear selector in the operational, it is still possible to steer the vehicle. PARK or REVERSE (manual transmission only) position.
420 STARTING AND OPERATING When parking on a hill, it is important to turn the front Manual Transmission — If Equipped wheels toward the curb on a downhill grade and away The foot operated parking brake is positioned below the from the curb on an uphill grade.
STARTING AND OPERATING 421 Automatic Transmission — If Equipped The foot operated parking brake is located below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully. To release the parking brake, press the park brake pedal a second time and let your foot up as you feel the brake disengage.
Page 424
422 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Do not leave the key fob in or near the vehicle (or to guard against vehicle movement and possible in a location accessible to children), and do not injury or damage. •...
STARTING AND OPERATING 423 OFF), the brakes will still function. The effort required to CAUTION! brake the vehicle will be much greater than that required with the power system operating. If the “Brake Warning Light” remains on with the parking brake released, a brake system malfunction NOTE: Your vehicle is equipped with a high perfor- is indicated.
424 STARTING AND OPERATING (ERM). These systems work together to enhance both If the “Brake System Warning Light” remains on or vehicle stability and control in various driving condi- comes on while driving, it indicates that the brake system tions. is not functioning properly and that immediate service is required.
Page 427
STARTING AND OPERATING 425 as ice, snow, gravel, bumps, railroad tracks, loose debris, WARNING! or panic stops may increase the likelihood of ABS activa- • The ABS contains sophisticated electronic equip- tion(s). ment that may be susceptible to interference You also may experience the following when ABS acti- caused by improperly installed or high output vates: radio transmitting equipment.
426 STARTING AND OPERATING If the “Anti-Lock Brake Warning Light” remains on or WARNING! (Continued) comes on while driving, it indicates that the anti-lock by the condition of the vehicle brakes and tires or portion of the brake system is not functioning and that the traction afforded.
STARTING AND OPERATING 427 reduce braking distances. The BAS complements the WARNING! (Continued) anti-lock brake system (ABS). Applying the brakes very must never be exploited in a reckless or dangerous quickly results in the best BAS assistance. To receive the manner, which could jeopardize the user’s safety or benefit of the system, you must apply continuous brak- the safety of others.
Page 430
428 STARTING AND OPERATING • Park brake must be off. WARNING! (Continued) • Driver door must be closed. such as on minor hills or with a loaded vehicle, or while pulling a trailer. HSA is not a substitute for • The vehicle must be on a sufficient grade. active driving involvement.
Page 431
STARTING AND OPERATING 429 WARNING! WARNING! (Continued) parking brake while parking on a hill and that the • If you use a trailer brake controller with your driver is responsible for braking the vehicle. trailer, the trailer brakes may be activated and deactivated with the brake switch.
430 STARTING AND OPERATING For vehicles not equipped with the DID, perform the 8. Turn the ignition switch to the OFF position and then following steps: back to the ON position. If the sequence was com- pleted properly, the “ESC Off Indicator Light” will 1.
STARTING AND OPERATING 431 • Understeer - when the vehicle is turning less than to the wheel that is not spinning. BLD may remain enabled even if TCS and ESC are in a reduced mode. appropriate for the steering wheel position. The “ESC Activation/Malfunction Indicator Light”...
Page 434
432 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) ESC performance. Improperly inflated and un- accidents, including those resulting from excessive evenly worn tires may also degrade ESC perfor- speed in turns, driving on very slippery surfaces, or hydroplaning. ESC also cannot prevent accidents mance.
Page 435
STARTING AND OPERATING 433 Partial Off WARNING! (Continued) The “Partial Off” mode is intended for times when a more the “ESC Off Indicator Light” will be illuminated. spirited driving experience is desired. This mode may When in “Partial Off” mode, the engine power modify TCS and ESC thresholds for activation, which reduction feature of TCS is disabled, and the allows for more wheel spin than normally allowed.
Page 436
434 STARTING AND OPERATING Full Off – If Equipped WARNING! This mode is intended for off-highway or off-road use • In the ESC “Full Off” mode, the engine torque only and should not be used on any public roadways. In reduction and stability features are disabled.
Page 437
STARTING AND OPERATING 435 malfunction has been detected in the ESC system. If this NOTE: light remains on after several ignition cycles, and the • The “ESC Activation/Malfunction Indicator Light” vehicle has been driven several miles (kilometers) at and the “ESC OFF Indicator Light” come on momen- speeds greater than 30 mph (48 km/h), see your autho- tarily each time the ignition switch is turned ON.
436 STARTING AND OPERATING Electronic Roll Mitigation (ERM) WARNING! This system anticipates the potential for wheel lift by Many factors, such as vehicle loading, road condi- monitoring the driver’s steering wheel input and the tions and driving conditions, influence the chance speed of the vehicle.
STARTING AND OPERATING 437 Rain Brake Support (RBS) TIRE SAFETY INFORMATION Rain Brake Support may improve braking performance Tire Markings in wet conditions. It will periodically apply a small amount of brake pressure to remove any water buildup on the front brake rotors. It functions when the wind- shield wipers are in LO or HI speed.
Page 440
438 STARTING AND OPERATING • Temporary spare tires are designed for temporary NOTE: emergency use only. Temporary high pressure com- • P (Passenger) — Metric tire sizing is based on U.S. pact spare tires have the letter “T” or “S” molded into design standards.
Page 441
STARTING AND OPERATING 439 Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 442
440 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions –...
STARTING AND OPERATING 441 Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on The TIN may be found on one or both sides of the tire, the outboard side, then you will find it on the inboard however, the date code may only be on one side.
442 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 01 = Number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.
Page 445
STARTING AND OPERATING 443 Term Definition Maximum Inflation Pressure The maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire. The maximum inflation pressure is molded into the sidewall. Recommended Cold Tire Inflation Vehicle manufacturer’s recommended cold tire inflation pressure Pressure as shown on the tire placard.
444 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Example Tire Placard Location (Door)
Page 447
STARTING AND OPERATING 445 Tire And Loading Information Placard Example Tire Placard Location (B-Pillar) Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry.
Page 448
446 STARTING AND OPERATING 3. Tire size designed for your vehicle. NOTE: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear 4. Cold tire inflation pressures for the front, rear, and axles must not be exceeded. For further information on spare tires.
Page 449
STARTING AND OPERATING 447 Steps For Determining Correct Load Limit— (5) Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may (1) Locate the statement “The combined weight of not safely exceed the available cargo and luggage load occupants and cargo should never exceed XXX kg or capacity calculated in Step 4.
Page 450
448 STARTING AND OPERATING Metric Example For Load Limit NOTE: • If your vehicle will be towing a trailer, load from your For example, if “XXX” amount equals 635 kg and there will be five 68 kg passengers in your vehicle, the amount trailer will be transferred to your vehicle.
450 STARTING AND OPERATING • Tread Wear WARNING! • Ride Comfort Overloading of your tires is dangerous. Overloading Safety can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the WARNING! recommended load capacity for your vehicle. Never overload them.
STARTING AND OPERATING 451 Fuel Economy WARNING! (Continued) Underinflated tires will increase tire rolling resistance • Unequal tire pressures can cause steering prob- resulting in higher fuel consumption. lems. You could lose control of your vehicle. • Unequal tire pressures from one side of the vehicle Ride Comfort And Vehicle Stability to the other can cause the vehicle to drift to the Proper tire inflation contributes to a comfortable ride.
Page 454
452 STARTING AND OPERATING judgement when determining proper inflation. Tires The cold tire inflation pressure must not exceed the may look properly inflated even when they are under- maximum inflation pressure molded into the tire side- inflated. wall. • Inspect tires for signs of tire wear or visible damage. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes.
STARTING AND OPERATING 453 Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds and WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
454 STARTING AND OPERATING Consult an authorized tire dealer for tire repairs and on ice. If your vehicle is equipped with Summer tires, be additional information. aware these tires are not designed for Winter or cold driving conditions. Install Winter tires on your vehicle Damaged Run Flat tires, or Run Flat tires that have when ambient temperatures are less than 40°F (5°C) or if experienced a loss of pressure should be replaced imme-...
STARTING AND OPERATING 455 Snow Tires While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be Some areas of the country require the use of snow tires poorer than that of non-studded tires. Some states pro- during the Winter.
456 STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continu- ously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed.
STARTING AND OPERATING 457 • Performance tires, tires with a speed rating of V or worn to the tread wear indicators, the tire should be replaced. Refer to “Replacement Tires” in this section for higher, and Summer tires typically have a reduced further information.
458 STARTING AND OPERATING Replacement Tires affect your vehicle’s handling. If you ever replace a wheel, make sure that the wheel’s specifications match The tires on your new vehicle provide a balance of many those of the original wheels. characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures.
STARTING AND OPERATING 459 WARNING! (Continued) CAUTION! braking of your vehicle. This can cause unpredict- Replacing original tires with tires of a different size able handling and stress to steering and suspen- may result in false speedometer and odometer read- sion components.
460 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tire Rotation — Same Tire Size On Front And Rear Axle The tires on the front and rear of your vehicle operate at different loads and perform different steering, driving, The suggested rotation method for vehicles equipped and braking functions.
STARTING AND OPERATING 461 Tire Rotation — Different Tire Size On Front And TIRE PRESSURE MONITOR SYSTEM (TPMS) Rear Axle The Tire Pressure Monitor System (TPMS) will warn the The suggested rotation method is the “side-to-side” as driver of a low tire pressure based on the vehicle recom- shown in the following diagram.
Page 464
462 STARTING AND OPERATING also increase as the vehicle is driven - this is normal and may need to be driven for up to 10 minutes above 15 mph there should be no adjustment for this increased pres- (24 km/h) in order for the TPMS to receive this informa- sure.
Page 465
STARTING AND OPERATING 463 inflated to the vehicle’s recommended cold placard pres- CAUTION! (Continued) sure value. • After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will CAUTION! prevent moisture and dirt from entering the valve •...
464 STARTING AND OPERATING • The TPMS is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure using an accurate tire pressure gauge, even if under-inflation has not reached the level to trigger illumination of the TPM Telltale Light.
Page 467
STARTING AND OPERATING 465 • Four TPM sensors, the vehicle’s recommended cold placard pressure infla- tion value. Once the system receives the updated tire • Various TPMS messages, which display in the Driver pressures, the system will automatically update, the Information Display (DID), and graphic display in the DID will return the pressure values •...
Page 468
466 STARTING AND OPERATING a minimum of five seconds and then display dashes (- -) 4. Using tire chains on the vehicle. in place of the pressure value to indicate which sensor is 5. Using wheels/tires not equipped with TPM sensors. not being received.
STARTING AND OPERATING 467 SYSTEM message for a minimum of five seconds and General Information then display dashes (- -) in place of the pressure value. This device complies with Part 15 of the FCC rules and RSS-210 of Industry Canada. Operation is subject to the 4.
468 STARTING AND OPERATING FUEL REQUIREMENTS octane number can cause engine failure and may void or not be covered by the New Vehicle Limited Warranty. 6.2L Supercharged And 6.4L Engine Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you experience these These engine are designed to meet all symptoms, try another brand of gasoline before consid- emissions regulations, provide opti-...
STARTING AND OPERATING 469 Gasoline/Oxygenate Blends Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol Some fuel suppliers blend unleaded gasoline with oxy- are not the responsibility of the manufacturer and may genates such as ethanol. void or not be covered under New Vehicle Limited Warranty.
470 STARTING AND OPERATING If a Non-FFV vehicle is inadvertently fueled with E-85 without MMT be used in your vehicle. The MMT content fuel, the engine will have some or all of these symptoms: of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer whether •...
STARTING AND OPERATING 471 available, the usage of Top Tier Detergent gasoline is CAUTION! (Continued) recommended. Visit www.toptiergas.com for a list of • An out-of-tune engine or certain fuel or ignition TOP TIER Detergent Gasoline Retailers. malfunctions can cause the catalytic converter to Indiscriminate use of fuel system cleaning agents should overheat.
472 STARTING AND OPERATING NOTE: Intentional tampering with the emissions control WARNING! (Continued) system can result in civil penalties being assessed against ventilation system to force fresh, outside air into you. the vehicle. Carbon Monoxide Warnings • Guard against carbon monoxide with proper main- tenance.
Page 475
STARTING AND OPERATING 473 CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap. • A poorly fitting fuel filler cap could let impurities into the fuel system. •...
474 STARTING AND OPERATING Loose Fuel Filler Cap Message WARNING! (Continued) If the vehicle diagnostic system determines that the fuel • Never add fuel to the vehicle when the engine is filler cap is loose, improperly installed, or damaged, a running.
STARTING AND OPERATING 475 • Gross Axle Weight Rating (GAWR) rear VEHICLE LOADING • Vehicle Identification Number (VIN) The load carrying capacity of your vehicle is shown on the “Vehicle Certification Label”. This information • Type of Vehicle should be used for passenger and luggage loading as •...
476 STARTING AND OPERATING Figure out the weight on the front and rear of the vehicle WARNING! separately. It is important that you distribute the load evenly over the front and rear axles. Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front Overloading can cause potential safety hazards and or rear GAWR.
Page 479
STARTING AND OPERATING 477 NOTE: Refer to the “Vehicle Certification Label” affixed to the rear of the driver’s door for your vehicle’s GVWR and GAWRs. TRAILER TOWING Trailer towing with this vehicle is not recommended. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF The Ground...
Page 480
478 STARTING AND OPERATING Recreational towing (with rear wheels on the ground) is CAUTION! NOT ALLOWED. The only acceptable method for tow- ing this vehicle (behind another vehicle) is on a vehicle Towing this vehicle in violation of the above require- trailer with all four wheels OFF the ground.
Page 481
WHAT TO DO IN EMERGENCIES CONTENTS ▫ Tire Service Kit Components And Operation . .485 HAZARD WARNING FLASHERS ...481 ▫ Tire Service Kit Usage Precautions ..486 IF YOUR ENGINE OVERHEATS .
Page 482
480 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE ...504 ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) ......507 ▫...
WHAT TO DO IN EMERGENCIES 481 HAZARD WARNING FLASHERS NOTE: With extended use the Hazard Warning flashers may wear down your battery. The Hazard Warning flasher switch is located in the switch bank near the bottom center of the instrument IF YOUR ENGINE OVERHEATS panel.
482 WHAT TO DO IN EMERGENCIES • You can also turn the temperature control to maximum CAUTION! heat, the mode control to floor and the blower control to high. This allows the heater core to act as a Driving with a hot cooling system could damage supplement to the radiator and aids in removing heat your vehicle.
WHAT TO DO IN EMERGENCIES 483 Torque Specifications Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Lug Nut/Bolt Torque **Lug Nut/ Lug Nut/ Bolt Size Bolt Socket Size 111 Ft-Lbs (150 N·m) M14 x 1.50 22 mm **Use only your Authorized Dealer recommended lug...
484 WHAT TO DO IN EMERGENCIES Tighten the lug nuts/bolts in a star pattern until each WARNING! nut/bolt has been tightened twice. To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered.
WHAT TO DO IN EMERGENCIES 485 Tire Service Kit Storage Tire Service Kit Components And Operation The Tire Service Kit is located in the trunk. Tire Service Kit Components Tire Service Kit Location 1 — Sealant Bottle 5 — Mode Select Knob 2 —...
486 WHAT TO DO IN EMERGENCIES Using The Mode Select Knob And Hoses Using The Power Button Your Tire Service Kit is equipped with the following Push and release the Power Button (4) once to symbols to indicate the air or sealant mode. turn On the Tire Service Kit.
Page 489
WHAT TO DO IN EMERGENCIES 487 from the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • For optimum performance, make sure the valve stem on the wheel is free of debris before connecting the Tire Service Kit.
Page 490
488 WHAT TO DO IN EMERGENCIES WARNING! WARNING! (Continued) • Keep Tire Service Kit away from open flames or • Do not attempt to seal a tire on the side of the heat source. vehicle closest to traffic. Pull far enough off the •...
WHAT TO DO IN EMERGENCIES 489 on the ground. This will provide the best positioning WARNING! (Continued) of the kit when injecting the sealant into the deflated • Tire Service Kit Sealant solution contains latex. In tire and running the air pump. Move the vehicle as case of an allergic reaction or rash, consult a phy- necessary to place the valve stem in this position sician immediately.
Page 492
490 WHAT TO DO IN EMERGENCIES • After pushing the Power Button (4), the sealant (white 4. Remove the cap from the valve stem and then screw the fitting at the end of the Sealant Hose (6) onto the fluid) will flow from the Sealant Bottle (1) through the valve stem.
Page 493
WHAT TO DO IN EMERGENCIES 491 2. Connect the Power Plug (8) to a different 12 Volt quickly from approximately 70 psi (4.8 Bar) to the power outlet in your vehicle or another vehicle, if actual tire pressure when the Sealant Bottle (1) is available.
Page 494
492 WHAT TO DO IN EMERGENCIES If the tire inflates to the recommended pressure or is at CAUTION! (Continued) least 26 psi (1.8 Bar) pressure within 15 minutes: • Failure to reinstall the cap on the fitting at the end 1.
Page 495
WHAT TO DO IN EMERGENCIES 493 3. Uncoil the Air Pump Hose (7) (black in color) and WARNING! screw the fitting at the end of hose (7) onto the valve stem. Tire Service Kit is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after 4.
Page 496
494 WHAT TO DO IN EMERGENCIES 2. Disconnect the Tire Service Kit from the valve stem, (F) Sealant Bottle And Hose Replacement: reinstall the cap on the valve stem and unplug from 12 1. Uncoil the Sealant Hose (6) (clear in color). Volt outlet.
WHAT TO DO IN EMERGENCIES 495 6. Verify that the cap is installed on the fitting at the end WARNING! of the Sealant Hose (6) and return the hose to its storage area (located on the bottom of the air pump). Do not attempt jump-starting if the battery is frozen.
496 WHAT TO DO IN EMERGENCIES Preparations For Jump-Start The battery is stored under an access cover in the trunk. Remote battery posts are located on the right side of the engine compartment for jump-starting. Remote Battery Posts Locations 1 — Remote Positive (+) Post 2 —...
WHAT TO DO IN EMERGENCIES 497 3. If using another vehicle to jump-start the battery, park WARNING! the vehicle within the jumper cables reach, set the • Take care to avoid the radiator cooling fan when- parking brake and make sure the ignition is OFF. ever the hood is raised.
Page 500
498 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Failure to follow these procedures could result in Do not connect the jumper cable to the negative (-) damage to the charging system of the booster vehicle post of the discharged battery. The resulting electri- or the discharged vehicle.
WHAT TO DO IN EMERGENCIES 499 Disconnecting The Jumper Cables CAUTION! 1. Disconnect the negative (-) end of the jumper cable Accessories plugged into the vehicle power outlets from the remote negative (-) post of the vehicle with draw power from the vehicle’s battery, even when not the discharged battery.
Page 502
500 WHAT TO DO IN EMERGENCIES accelerator. Use the least amount of accelerator pedal NOTE: Push the ESC Off switch to place the Electronic pressure that will maintain the rocking motion, without Stability Control (ESC) system in Partial Off mode spinning the wheels or racing the engine.
WHAT TO DO IN EMERGENCIES 501 MANUAL PARK RELEASE — 8 SPEED CAUTION! TRANSMISSION • When “rocking” a stuck vehicle by shifting be- WARNING! tween DRIVE / 1ST GEAR and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or Always secure your vehicle by fully applying the drivetrain damage may result.
Page 504
502 WHAT TO DO IN EMERGENCIES Follow these steps to use the Manual Park Release: 3. Using a small screwdriver or similar tool, fish the tether strap up through the opening in the console 1. Firmly apply the parking brake. base.
Page 505
WHAT TO DO IN EMERGENCIES 503 5. While holding the locking tab in the disengaged To Reset The Manual Park Release: position, pull the tether strap to rotate the lever up and 1. Push the latch (at the base of the lever, on the rear side) rearward until it locks in place in the vertical position.
Page 506
504 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. Towing Condition Wheels OFF The Ground AUTOMATIC TRANSMISSION/ MANUAL TRANSMISSION Flat Tow NONE If transmission is operable: •...
WHAT TO DO IN EMERGENCIES 505 If you must use the accessories (wipers, defrosters, etc.) Automatic Transmission while being towed, the ignition must be in the ON/RUN The manufacturer recommends towing your vehicle with position, not the ACC position. all four wheels OFF the ground using a flatbed. If flatbed equipment is not available, and the transmission CAUTION! is operable, the vehicle may be flat towed (with all four...
506 WHAT TO DO IN EMERGENCIES If flatbed equipment is not available, and the transmis- CAUTION! sion is operable, the vehicle may be flat towed (with all four wheels on the ground) under the following condi- Towing this vehicle in violation of the above require- tions: ments can cause severe transmission damage.
WHAT TO DO IN EMERGENCIES 507 ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) This vehicle is equipped with an Enhanced Accident Response System. EVENT DATA RECORDER (EDR) This vehicle is equipped with an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...
514 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors further damage to the emission control system. It the performance of the emissions, engine, and automatic could also affect fuel economy and driveability.
MAINTAINING YOUR VEHICLE 515 access this information to assist with the diagnosis and For further information, refer to “Privacy Practices — If service of your vehicle and emissions system. Equipped With Uconnect 8.4 Radio” and “Uconnect CyberSecurity” in “All About Uconnect Access” in your WARNING! Owner’s Manual Radio Supplement and “Cybersecurity”...
516 MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE Your vehicle has a simple ignition actuated test, which PROGRAMS you can use prior to going to the test station. To check if your vehicle’s OBD II system is ready, you must do the In some localities, it may be a legal requirement to pass following: an inspection of your vehicle’s emissions control system.
MAINTAINING YOUR VEHICLE 517 the ignition or start the engine. This means that your before going to the I/M station. The I/M station can fail vehicle’s OBD II system is not ready and you should your vehicle because the MIL is on with the engine not proceed to the I/M station.
518 MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control Besides those maintenance items specified in the fixed systems may void your warranty and could result in civil “Maintenance Schedule”, there are other components penalties being assessed against you. which may require servicing or replacement in the future. WARNING! CAUTION! •...
MAINTAINING YOUR VEHICLE 519 (.95 liters) of oil when the reading is at the bottom of the CAUTION! (Continued) “SAFE” range will result in an oil level at the top of the transmission, or air conditioning. Such damage is “SAFE” range on these engines. not covered by the New Vehicle Limited Warranty.
Page 522
520 MAINTAINING YOUR VEHICLE Engine Oil Selection CAUTION! For best performance and maximum protection under all Do not use chemical flushes in your engine oil as the types of operating conditions, the manufacturer only chemicals can damage your engine. Such damage is recommends full synthetic engine oils that meet the not covered by the New Vehicle Limited Warranty.
Page 523
MAINTAINING YOUR VEHICLE 521 Synthetic Engine Oils Engine Oil Change Requirements — 6.2L Supercharged Engine (If Equipped) You may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- We recommend having your oil changed and vehicle mended maintenance intervals for oil and filter changes serviced by your authorized dealer.
522 MAINTAINING YOUR VEHICLE To access these oil drains, the vehicle needs to be safely WARNING! (Continued) lifted and supported to remove the front underbody you have any doubt about your ability to perform a shields (belly pan). Your service technician will refer to service job, take your vehicle to a competent me- the Service Manual for proper under body shield (belly chanic.
MAINTAINING YOUR VEHICLE 523 Engine Oil Filter Selection WARNING! (Continued) This manufacturer’s engines have a full-flow type oil cleaner, hoses, etc.) unless such removal is necessary filter. Use a filter of this type for replacement. The quality for repair or maintenance. Make sure that no one is of replacement filters varies considerably.
524 MAINTAINING YOUR VEHICLE Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. NOTE: The battery is stored under an access cover in the trunk. Remote battery terminals are located in the engine compartment for jump-starting.
MAINTAINING YOUR VEHICLE 525 WARNING! (Continued) CAUTION! over a battery when attaching clamps. If acid • It is essential when replacing the cables on the splashes in eyes or on skin, flush the area imme- battery that the positive cable is attached to the diately with large amounts of water.
Page 528
526 MAINTAINING YOUR VEHICLE include cleaning of the condenser fins and a performance CAUTION! test. Drive belt tension should also be checked at this time. Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- WARNING! tioning components.
Page 529
MAINTAINING YOUR VEHICLE 527 Refrigerant Recovery And Recycling R1234yf — If 1. Remove the access door in the cowl screen by pressing Equipped the retaining clips. R-1234yf Air Conditioning Refrigerant is a hydrofluoole- fine HFO that is endorsed by the Environmental Protec- tion Agency and is an ozone-saving product with a low GWP (Global Warming Potential).
Page 530
528 MAINTAINING YOUR VEHICLE Filter Access Cover A/C Air Filter 3. Remove the used filter. 5. Close the filter access cover. 4. Install the new filter with arrows pointing in the Refer to the “Maintenance Schedule” for the proper direction of airflow, which is toward the rear of the maintenance intervals.
MAINTAINING YOUR VEHICLE 529 Body Lubrication Windshield Wiper Blades Locks and all body pivot points, including such items as Clean the rubber edges of the wiper blades and the seat tracks, door hinge pivot points and rollers, liftgate, windshield periodically with a sponge or soft cloth and a tailgate, decklid, sliding doors and hood hinges, should mild nonabrasive cleaner.
530 MAINTAINING YOUR VEHICLE Adding Washer Fluid The fluid reservoir will hold nearly 1 gal (4 l) of washer fluid when the message “Low Washer Fluid” appears in The windshield washer fluid reservoir is located in the the Driver’s Information Display (DID). front of the engine compartment.
Page 533
MAINTAINING YOUR VEHICLE 531 have an authorized technician inspect the complete ex- WARNING! (Continued) haust system and adjacent body areas for broken, dam- • A hot exhaust system can start a fire if you park aged, deteriorated, or mispositioned parts. Open seams over materials that can burn.
Page 534
532 MAINTAINING YOUR VEHICLE In unusual situations involving grossly malfunctioning CAUTION! (Continued) engine operation, a scorching odor may suggest severe In the event of engine malfunction, particularly and abnormal catalyst overheating. If this occurs, stop involving engine misfire or other apparent loss of the vehicle, turn off the engine and allow it to cool.
MAINTAINING YOUR VEHICLE 533 NOTE: Your vehicles exhaust system may be equipped WARNING! (Continued) with an Electronic Exhaust Valve (EEV) system, if the time to cool. Never try to open a cooling system exhaust system is replaced with aftermarket products a pressure cap when the radiator is hot.
Page 536
534 MAINTAINING YOUR VEHICLE tears, cuts, and tightness of the connection at the bottle If the engine coolant (antifreeze) is dirty or contains and radiator. Inspect the entire system for leaks. visible sediment, have an authorized dealer clean and flush with OAT coolant (antifreeze) (conforming to With the engine at normal operating temperature (but MS.90032).
Page 537
MAINTAINING YOUR VEHICLE 535 CAUTION! CAUTION! (Continued) rust inhibitors or antirust products, as they may not • Mixing of engine coolant (antifreeze) other than be compatible with the engine coolant and may specified Organic Additive Technology (OAT) en- plug the radiator. gine coolant (antifreeze), may result in engine •...
Page 538
536 MAINTAINING YOUR VEHICLE Please review these recommendations for using Organic (antifreeze) solution. The use of lower quality water Additive Technology (OAT) engine coolant (antifreeze) will reduce the amount of corrosion protection in the that meets the requirements of FCA Material Standard engine cooling system.
Page 539
MAINTAINING YOUR VEHICLE 537 have a authorized dealer drain, flush, and refill with WARNING! OAT coolant (conforming to MS.90032) as soon as • Do not open hot engine cooling system. Never add possible. engine coolant (antifreeze) when the engine is Cooling System Pressure Caps overheated.
Page 540
538 MAINTAINING YOUR VEHICLE engine coolant in open containers or allow it to remain in When additional coolant is needed to maintain the puddles on the ground. If ingested by a child or pet, seek proper level, it should be added to the coolant bottle. Do emergency assistance immediately.
MAINTAINING YOUR VEHICLE 539 • Check the coolant freeze point in the radiator and in the • Do not change the thermostat for Summer or Winter coolant expansion bottle. If engine coolant (antifreeze) operation. If replacement is ever necessary, install ONLY needs to be added, the contents of the coolant expansion the correct type thermostat.
Page 542
540 MAINTAINING YOUR VEHICLE Master Cylinder — Brake Fluid Level Check Use only manufacturer’s recommended brake fluid. Re- fer to “Fluids, Lubricants, and Genuine Parts” in “Main- Check the fluid level in the master cylinder immediately taining Your Vehicle” for further information. if the “Brake Warning Light”...
MAINTAINING YOUR VEHICLE 541 Use only brake fluid that has been in a tightly closed WARNING! (Continued) container to avoid contamination from foreign matter or cylinder reservoir cap secured at all times. Brake moisture. fluid in a open container absorbs moisture from the Clutch Hydraulic System (Manual Transmission) air resulting in a lower boiling point.
542 MAINTAINING YOUR VEHICLE Manual Transmission — If Equipped Automatic Transmission — If Equipped Fluid Level Check Selection Of Lubricant Check the fluid level by removing the fill plug on the left It is important to use the proper transmission fluid to side of the transmission.
Page 545
MAINTAINING YOUR VEHICLE 543 CAUTION! (Continued) CAUTION! shudder. Refer to “Fluids, Lubricants, And Genuine Do not use chemical flushes in your transmission as Parts” in this section for fluid specifications. the chemicals can damage your transmission compo- nents. Such damage is not covered by the New Special Additives Vehicle Limited Warranty.
544 MAINTAINING YOUR VEHICLE with an improper fluid level can cause severe transmis- Rear Axle sion damage. Fluid Level Check Checking the fluid level while the vehicle is on level CAUTION! ground and has been stationary for 15 minutes will If a transmission fluid leak occurs, visit your autho- improve the accuracy of the fluid level reading.
MAINTAINING YOUR VEHICLE 545 Appearance Care And Protection From Corrosion What Causes Corrosion? Corrosion is the result of deterioration or removal of Protection Of Body And Paint From Corrosion paint and protective coatings from your vehicle. Vehicle body care requirements vary according to geo- graphic locations and usage.
Page 548
546 MAINTAINING YOUR VEHICLE • If insects, tar, or other similar deposits have accumu- Special Care lated on your vehicle, use MOPAR Super Kleen Bug • If you drive on salted or dusty roads or if you drive and Tar Remover to remove. near the ocean, hose off the undercarriage at least once •...
Page 549
MAINTAINING YOUR VEHICLE 547 • If you carry special cargo such as chemicals, fertilizers, control dust on dirt roads. Use a soft cloth or sponge and de-icer salt, etc., be sure that such materials are well mild soap to wipe away promptly. Do not use harsh packaged and sealed.
Page 550
548 MAINTAINING YOUR VEHICLE When cleaning extremely dirty wheels including exces- NOTE: If you intend parking or storing your vehicle for sive brake dust, care must be taken in the selection of tire an extended period after cleaning the wheels with wheel and wheel cleaning chemicals and equipment to prevent cleaner, drive your vehicle for a few minutes before doing damage to the wheels.
Page 551
MAINTAINING YOUR VEHICLE 549 Stain Repel Fabric Cleaning Procedure — If Interior Care Equipped Use MOPAR Total Clean to clean fabric upholstery and Stain Repel seats may be cleaned in the following manner: carpeting. • Remove as much of the stain as possible by blotting Use MOPAR Total Clean to clean vinyl upholstery.
Page 552
550 MAINTAINING YOUR VEHICLE WARNING! CAUTION! Damage caused by these type of products may not be Do not use volatile solvents for cleaning purposes. covered by your New Vehicle Limited Warranty. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. CAUTION! CAUTION! Do not use Alcohol and Alcohol-based and/or Keton...
Page 553
MAINTAINING YOUR VEHICLE 551 To minimize the possibility of scratching the lenses and When cleaning the rear view mirror, spray cleaner on the reducing light output, avoid wiping with a dry cloth. To towel or cloth that you are using. Do not spray cleaner remove road dirt, wash with a mild soap solution fol- directly on the mirror.
552 MAINTAINING YOUR VEHICLE If the belts need cleaning, use MOPAR Total Clean, a mild Cleaning The Center Console Cupholders soap solution, or lukewarm water. Do not remove the Clean with a damp cloth or towel using a mild detergent belts from the vehicle to wash them.
MAINTAINING YOUR VEHICLE 553 WARNING! (Continued) • Before replacing a fuse, make sure that the ignition is off and that all the other services are switched off and/or disengaged. • If the replaced fuse blows again, contact an autho- rized dealer. •...
Page 556
554 MAINTAINING YOUR VEHICLE CAUTION! (Continued) CAUTION! (Continued) use of a fuse with a rating other than indicated may allow water to get into the power distribution result in a dangerous electrical system overload. If center and possibly result in an electrical system failure.
Page 557
MAINTAINING YOUR VEHICLE 555 Cavity Cartridge Fuse Mini-Fuse Description 30 Amp Pink – Electronic Stability Control 20 Amp Blue – Police Ignition Run / ACC #1 20 Amp Blue – Police Ignition Run / ACC # 2 – 20 Amp Yellow All-Wheel Drive Module –...
Page 558
556 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description 50 Amp Red – Electric Power Steering #2 – If Equipped / Radiator Fan (6.2L Super- charged) 30 Amp Pink – Wiper Motor 30 Amp Pink – Headlamp Washers – If Equipped 20 Amp Blue –...
MAINTAINING YOUR VEHICLE 559 Rear Power Distribution Center (Fuses) There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays. Fuse cavity location and de- scriptions are printed on the inside of the power distri- bution center cover.
Page 562
560 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! (Continued) • When replacing a blown fuse, it is important to use • When installing the power distribution center cover, only a fuse having the correct amperage rating. The it is important to ensure the cover is properly posi- use of a fuse with a rating other than indicated may tioned and fully latched.
Page 563
MAINTAINING YOUR VEHICLE 561 Cavity Cartridge Fuse Mini-Fuse Description 30 Amp Pink – Interior Lighting 40 Amp Green – Power Locks 30 Amp Pink – Driver Door Control Module 30 Amp Pink – Passenger Door Control Module – 20 Amp Yellow Dual USB Center Console Rear/Cigar Lighter IP –...
Page 564
562 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description – – Fuse – Spare 30 Amp Pink – Fuel Pump – 20 Amp Yellow – Police Right Spot Lamp – Police – 10 Amp Red Fuel Door/Diagnostic Port – 10 Amp Red Integrated Center Stack –...
Page 565
MAINTAINING YOUR VEHICLE 563 Cavity Cartridge Fuse Mini-Fuse Description – 15 Amp Blue Ignition Switch/RF Hub Module/Steering Column Lock (300) – If Equipped – 10 Amp Red Steering Column Module/Clock (300) – 5 Amp Tan Battery Sensor – 15 Amp Blue Electronic Exhaust Valve –...
Page 566
564 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description – 20 Amp Yellow Comfort Seat And Steer- ing Wheel Module (Heated Steering Wheel/RR Heated Seats) – 10 Amp Red Park Assist / Blind Spot / Rear View Camera – 15 Amp Blue Cluster / Rearview Mir- ror / Compass (Charger/ 300) / Humidity Sensor...
Page 567
MAINTAINING YOUR VEHICLE 565 Cavity Cartridge Fuse Mini-Fuse Description – – Fuse – Spare – – Fuse – Spare – 20 Amp Yellow Front Heated Seats – If Equipped – 10 Amp Red Heated Cupholders/Rear Heated Seat Switches – If Equipped –...
568 MAINTAINING YOUR VEHICLE VEHICLE STORAGE in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the If you are leaving your vehicle dormant for more than 21 possibility of compressor damage when the system is days, you may want to take these steps to protect your started again.
Page 571
MAINTAINING YOUR VEHICLE 569 Bulb Number Door Courtesy Shift Indicator Lamp JKLE14140 Optional Door Map Pocket/Cupholder LED (Serviced at Authorized Dealer) For lighted switches, see your authorized dealer for replacement instructions. Exterior Bulbs Bulb Number Headlamp – High Intensity Discharge (HID) D3S (Serviced at Authorized Dealer) * Halogen Headlamp HIR2LL...
570 MAINTAINING YOUR VEHICLE Bulb Number Backup Lamp LED (Serviced at Authorized Dealer) Center High-Mount Stop Lamp (CHMSL) LED (Serviced at Authorized Dealer) License LED (Serviced at Authorized Dealer) * The headlamps are a type of high-voltage discharge Low Beam Headlamp, High Beam Headlamp, tube.
Page 573
MAINTAINING YOUR VEHICLE 571 5. Remove bulb by turning it counter clockwise and 4. Reach behind the passenger headlamp assembly. disconnect. 5. Remove the headlamp cover. 6. Install new bulb by turning it clockwise and reconnect. 6. Turn the headlamp access cap counterclockwise to 7.
Page 574
572 MAINTAINING YOUR VEHICLE Low Beam Headlamp, High Beam Headlamp, and WARNING! Park/Turn Lamp — Models With High Intensity Discharge (HID) Headlamps — If Equipped A transient high voltage occurs at the bulb sockets of HID headlamps when the headlamp switch is turned HID Headlamps ON.
MAINTAINING YOUR VEHICLE 573 Front/Rear Side Marker Lamp Center High-Mounted Stop Lamp (CHMSL) The Side Markers use LED lamps that are not serviceable The CHMSL uses LED lamps that are not serviceable separately. The Side Markers must be replaced as an separately.
576 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS CAUTION! (Continued) Important Information need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an au- CAUTION! thorized dealer as soon as possible. • Do not use water alone or alcohol-based engine •...
MAINTAINING YOUR VEHICLE 577 Engine Component Fluid, Lubricant, or Genuine Part Engine/Intercooler Coolant We recommend you use MOPAR Antifreeze/Coolant 10 Year/ 150,000 Mile Formula OAT coolant conforming to MS.90032. Engine Oil For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils.
578 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Manual Transmission – If We recommend you use MOPAR ATF+4 Automatic Transmission Fluid. Equipped Automatic Transmission – If Use only MOPAR ZF 8&9 Speed ATF Automatic Transmission Fluid, or Equipped equivalent.
Page 582
580 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE Based on engine operation conditions, the oil change indicator message will illuminate. This means that ser- The Scheduled Maintenance services listed in this vice is required for your vehicle. Have your vehicle manual must be done at the times or mileages specified serviced as soon as possible, within the next 500 miles to protect your vehicle warranty and ensure the best (805 km).
Page 583
MAINTENANCE SCHEDULES 581 • Inspect the battery, and clean and tighten the terminals Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a as required. scheduled oil change is performed by someone other •...
Page 585
MAINTENANCE SCHEDULES 583 Miles: 102 108 114 120 126 132 138 144 150 Months: Kilome- ters: Rotate the tires, ro- tate at the first sign of irregular wear, even if it occurs before scheduled mainte- nance.
Page 586
584 MAINTENANCE SCHEDULES Miles: 102 108 114 120 126 132 138 144 150 Months: Kilome- ters: Inspect front sus- pension, tie rod ends, and boot seals, for cracks or leaks and all parts for damage, wear, im- proper looseness or end play;...
Page 587
MAINTENANCE SCHEDULES 585 Miles: 102 108 114 120 126 132 138 144 150 Months: Kilome- ters: If using your ve- hicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; re- place if necessary.
Page 588
586 MAINTENANCE SCHEDULES Miles: 102 108 114 120 126 132 138 144 150 Months: Kilome- ters: Inspect the brake lin- ings; re- place if necessary. Inspect the CV joints. Inspect the exhaust system.
Page 589
MAINTENANCE SCHEDULES 587 Miles: 102 108 114 120 126 132 138 144 150 Months: Kilome- ters: Adjust the parking brake on vehicles equipped with four wheel disc brakes. Inspect the manual transmis- sion fluid (If Equipped).
Page 591
MAINTENANCE SCHEDULES 589 Miles: 102 108 114 120 126 132 138 144 150 Months: Kilome- ters: Change the rear axle fluid if using your vehicle for any of the following: police, taxi, fleet or frequent trailer towing. Replace the engine air cleaner filter.
Page 592
590 MAINTENANCE SCHEDULES Miles: 102 108 114 120 126 132 138 144 150 Months: Kilome- ters: Replace the air condition- ing filter. Inspect and re- place the PCV Valve if neces- sary Replace the spark plugs – 6.2L Super- charged Engine **...
Page 593
MAINTENANCE SCHEDULES 591 Miles: 102 108 114 120 126 132 138 144 150 Months: Kilome- ters: Replace the spark plugs – 6.4L Engine ** Flush and replace the engine coolant at 120 months if not done at 150,000 miles (240,000 km).
Page 594
592 MAINTENANCE SCHEDULES ** The spark plug change interval is mileage based only, yearly intervals do not apply. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 595
IF YOU NEED CONSUMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ....595 Speech Impaired (TDD/TTY) ... . .597 ▫...
Page 596
594 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... . .602 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES ..601 ▫...
IF YOU NEED CONSUMER ASSISTANCE 595 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
596 IF YOU NEED CONSUMER ASSISTANCE • Authorized dealer name facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized FCA US LLC Customer Center dealer service manager first.
IF YOU NEED CONSUMER ASSISTANCE 597 In Mexico Contact Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) Av. Prolongacion Paseo de la Reforma, 1240 To assist customers who have hearing difficulties, the Sante Fe C.P. 05109 manufacturer has installed special TDD (Telecommuni- Mexico, D.
Page 600
598 IF YOU NEED CONSUMER ASSISTANCE Warranty expires. The manufacturer stands behind only We appreciate that you have made a major investment the manufacturer’s service contracts. If you purchased a when you purchased the vehicle. An authorized dealer manufacturer’s service contract, you will receive Plan has also made a major investment in facilities, tools, and Provisions and an Owner Identification Card in the mail training to assure that you are absolutely delighted with...
IF YOU NEED CONSUMER ASSISTANCE 599 WARRANTY INFORMATION If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in See the Warranty Information Booklet, located on the a group of vehicles, it may order a recall and remedy DVD, for the terms and provisions of FCA US LLC campaign.
600 IF YOU NEED CONSUMER ASSISTANCE In Canada Service Manuals If you believe that your vehicle has a safety defect, you These comprehensive Service Manuals provide the infor- should contact the Customer Service Department imme- mation that students and professional technicians need in diately.
IF YOU NEED CONSUMER ASSISTANCE 601 Owner’s Manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES These Owner’s Manuals have been prepared with the The following tire grading categories were established by assistance of service and engineering specialists to ac- the National Highway Traffic Safety Administration. The quaint you with specific FCA US LLC vehicles.
602 IF YOU NEED CONSUMER ASSISTANCE Treadwear Traction Grades The Treadwear grade is a comparative rating, based on The Traction grades, from highest to lowest, are AA, A, B, the wear rate of the tire when tested under controlled and C. These grades represent the tire’s ability to stop on conditions on a specified government test course.
IF YOU NEED CONSUMER ASSISTANCE 603 Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, The temperature grade for this tire is established for representing the tire’s resistance to the generation of heat a tire that is properly inflated and not overloaded. and its ability to dissipate heat, when tested under Excessive speed, under-inflation, or excessive load- controlled conditions on a specified indoor laboratory...
Page 625
INDEX 623 Speed Control Starting And Operating .....376 Accel/Decel ......157, 158 Starting Procedures .
Page 626
624 INDEX System, Remote Starting .....27 High Speed ......453 Inflation Pressures .
Page 627
INDEX 625 SRT ....... . .272 Trunk Release Remote Control ....41 Towing .
Page 628
626 INDEX Unleaded Gasoline ......468 Washing Vehicle ......545 Untwisting Procedure, Seat Belt .
Page 629
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.