Table of Contents
Advertisement
speCiAlsettinGs
» KB Frequency (MHz)«: Enter the user
band frequency assigned to the user
band with »1...0« buttons.
» LNB Selection«: If more than one
satellites are used in the current SCR
system, select »1/2« to»2/2« for the
satellite corresponding to the relevant
positions using »
notes:
Use installation equipment supported /
7
suggested by your Multiswitch.
Other users / receivers connected to the
7
system may be affected if the specified user
band number and frequency is changed
during installation.
User band and User band frequency is
7
specified on the Multiswitch used; and
each user / receiver uses a specified user
band and user band frequency.
With SCR satellite system, auto search by
7
several users / receivers at the same time
may cause problems.
– » DISEqC mode« and »LNB selection«:
depending on the type of antenna used,
B
A
»
«
»
use
or
» DiSEqC 1.0« or »DiSEqC 1.1«.
» Off«: for a satellite system with only
one antenna.
» D iSEqC 1.0«: allows up to four satel-
lites to be received simultaneously.
U nder »LNB selection«, use
A
»
«
or
to select the option »1/4«,
»2/4«, »3/4« or »4/4«.
» D iSEqC 1.1«: allows up to 16 satel-
lites to be received simultaneously.
U nder »LNB selection«, use
A
»
«
to select the option »1/16« to
»16/16«.
m
5 Press »
« to end the setting.
- ---------------------------------------------------------------------------------------------------------
B
A
« or »
« buttons.
«
select the option »Off«,
B
»
settingsformotorisedantennas
(DiseqC1.2)
Your television set supports motorised satellite
systems in compliance with DiSEqC 1.2. This
function allows the satellite antenna to be oper-
ated via the television set.
1 Open the menu with »m«.
2 Select the line »SOURCE SETUP« with
»D«
or
and press »oK« to confirm.
– T he »SOURCE SETUP« menu appears.
3 Select the line »DiSEqC 1.2« with
»D«
. Select the option »On« with
A
»
«
– T he line »User Mode« is active.
note:
Additional operations are explained in the
7
following sections.
usermode
You can adjust the alignment of the satellite an-
tenna to each individual satellite. These settings
will be saved so that the antenna can later be
easily guided to each saved alignment.
1 Select the line »User mode« with
»D«
and press »oK« to confirm.
– T he »USER MODE« menu appears.
2 Select the preferred option with
»D«
.
– » Satellite«: »Press oK«, select a satellite
B
»
«
B
»
with
»oK« to confirm.
– » Transponder«: »Press ●«, select the tran-
sponder from which the signal is being
«
r eceived with
or
and press »oK« to confirm.
– » Moving Mode«: Use
lect the option »Discrete« or »Continuous«.
– » Discrete«: Moves the antenna in
d efined steps to the west and the east.
– » Continuous«: Moves the antenna to the
west or east continuously.
A
«
»
«
»C«
»D«
,
,
or
B
A
»
«
»
«
»C«
,
,
B
»
«
or
ENGLISH
»C«
»C«
or
B
»
«
or
»C«
or
»C«
or
and press
»D«
or
A
»
«
to se-
4 7
Advertisement
Table of Contents
