Related Manuals for Audiovox PROFESSIONAL Series
Summary of Contents for Audiovox PROFESSIONAL Series
- Page 1 PROFESSIONAL SERIES Remote Start with Keyless Entry Installation Guide CA6150RX 2010 Audiovox Electronics Corporation. All rights reserved.
-
Page 2: Table Of Contents
Manual Feature Programming ..............16 Programming Feature Banks ..............17 Tach Programming .................. 18 Smart Tachless.Mode ................18 Feature Descriptions ................19 Transmitter Button Functions ............. 22 Remote Start Shutdown Diagnostics ..........23 System Layout ..................24 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 3: Before You Begin
Use a Digital Multi Meter for testing and verifying circuits. DO NOT USE A TEST LIGHT, OR "COMPUTER SAFE PROBE" as these can set off air bags or damage vehicle computers. Technical Support (800) 421-3209 or go to http://techservices.codesystems.com 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 4: Wire Connection Guide
8 Pin Main Harness 3 Pin Parking Light Harness 6 Pin Start Harness 4 Pin Auxiliary Output Harness 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 5: Pin Main Harness
Verification: This wire will register at positive voltage and register ground when the horn switch is pressed. Connect the BROWN/BLACK wire to the vehicle’s horn wire. This is a low current output, 500mA. 2010 Audiovox Electronics Corporation. All rights reserved. - Page 6 Wire Jump To PINK BLUE/BLACK Active Outpu t Wire From Ignition Output Wire Control Module Wire From Control Module To Vehicle's 2nd or 3rd Accessory Wire To Vehicle's 2nd or 3rd Ignition Wire 2010 Audiovox Electronics Corporation. All rights reserved.
- Page 7 Locate the vehicle’s brake light wire at the brake pedal mounted switch. Verification: This wire registers positive voltage when the brake pedal is pressed. Connect the BROWN/RED wire to the vehicle’s brake light wire. 2010 Audiovox Electronics Corporation. All rights reserved.
-
Page 8: Pin Parking Light Harness
Verification: This wire registers voltage only when the key is turned to the START position. Verification: The starter wire registers voltage when the key is turned to the START position. Connect the PURPLE wire to the vehicle starter wire. 2010 Audiovox Electronics Corporation. All rights reserved. - Page 9 Verification: This wire will register ( + ) voltage in all positions of the ignition switch. Connect the RED wire to the constant 12 Volt battery wire. NOTE: Remove all fuses until all connections are made. 2010 Audiovox Electronics Corporation. All rights reserved.
-
Page 10: Pin Auxiliary Harness
This is typically used to re-lock the vehicle’s doors if they unlock upon remote start shutdown. It can also be used to pulse a door pin- switch wire to prevent the vehicle’s accessories from remaining on after remote start shutdown. 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 11: Pin Door Lock Output Harness
Please review the wire and location chart to see which type of door lock system is in your vehicle. The most common types are shown in the following diagrams. 2010 Audiovox Electronics Corporation. All rights reserved. - Page 12 Connect the GREEN and BLUE wires shown in the diagram below. Positive Locks: Fused +12 Volt Battery Souce GREEN (-) Lock Output Lock Fused +12 Volt Vehicle Door Lock Battery Souce Control Relays Unlock BLUE (-) Unlock Output 2010 Audiovox Electronics Corporation. All rights reserved.
- Page 13 Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPDT relays (not supplied). Multiplex Locks: Ground Fused +12 Volt GREEN (-) Lock Output BLUE (-) Unlock Output Battery Source Resistor Lock Vehicle Door Lock Control Relays Unlock 2010 Audiovox Electronics Corporation. All rights reserved.
- Page 14 BLUE wires shown in the diagram below using (2) SPDT relays (not supplied). Fused +12 Volt Battery Source Door Lock GREEN (-) Lock Output Actuator Chassis Ground Fused +12 Volt Battery Source BLUE (-) Unlock Output Chassis Ground 2010 Audiovox Electronics Corporation. All rights reserved.
-
Page 15: Additional Ports
Transponder Interface Activation Factory Alarm Arm / Disarm Manual Arm / Disarm Inputs (factory keyless controls system) Tracking Port This 4 pin port is used for Code Alarm Car Link or Vehicle Tracking accessories. 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 16: Set Up & Programming
2 - 4 chirps. NOTE: The system will remain in feature programming mode as long as the ignition is on, there is no time limit. To exit programming turn the IGNITION OFF. 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 17: Programming Feature Banks
Lock and 3 Ignition Controlled Locks Lock Only Unlock Only Unlock 4 Horn Output Timing 16mS 10mS 30mS 40mS 50mS 5 Real Panic Latched until 6 AUX 1 Push and Hold Latched IGN ON 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 18: Tach Programming
Within the 7 flash time period, press and hold the button. The system will chirp 1 time indicating the system is now in tachless mode. 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 19: Feature Descriptions
Factory Disarm - Single 1 second pulse with unlock and remote start activation. 2nd Unlock - Single 1 second pulse with 2nd press of unlock. Start Status - Continuous ( - ) output during the remote start cycle. 2010 Audiovox Electronics Corporation. All rights reserved. - Page 20 3 - Running Lights: Controls the WHITE parking light output wire during remote start. Steady - Parking lights constant during the remote start cycle. Flashing - Parking lights flash at a slow pace during the remote start cycle. 2010 Audiovox Electronics Corporation. All rights reserved.
- Page 21 45 Second Delay - Diesel engine, delays the starter output wire for 45 seconds after the ignition has been powered up by the remote start. 2010 Audiovox Electronics Corporation. All rights reserved.
-
Page 22: Transmitter Button Functions
Shut Down Run Time Press and Release 4 times. Extention Ignition ON/OFF, Press and Hold 2 / 3 Hour Start Valet Button, Press Start 4 times Daily Start Timer Press Lock + Start 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 23: Remote Start Shutdown Diagnostics
To manually enter diagnostics and view the last shutdown, turn the ignition ON and press and release the button. LED FLASHES SHUTDOWN ZONE 3 Flashes Hood Input Brake Input 4 Flashes Remote Start Valet Mode 7 Flashes Tach not learned / Crank Average not learned 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 24: System Layout
CA6150RX 2010 Audiovox Electronics Corporation. All rights reserved. - Page 25 2010 Audiovox Electronics Corporation. All rights reserved.
- Page 26 2. This device must accept any interference received, including any interference that may cause undesired operation. Warning! Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2010 Audiovox Electronics Corporation. All rights reserved.