Ryobi EMS216L Manual
  1. Manuals
  2. Brands
  3. Ryobi Manuals
  4. Saw
  5. EMS216L
  6. Manual
Ryobi EMS216L Manual

Ryobi EMS216L Manual

Hide thumbs Also See for EMS216L:
Table of Contents

Advertisement

Quick Links

Download this manual
FRONT PAGE
EMS216L

Advertisement

Table of Contents
loading

Related Manuals for Ryobi EMS216L

Summary of Contents for Ryobi EMS216L

  • Page 1 FRONT PAGE EMS216L...

  • Page 2: Intended Use

    refrigerators. There is an increased risk of electric IMPORTANT! shock if your body is earthed or grounded. It is essential that you read the instructions in this manual ■ Do not expose power tools to rain or wet conditions. before assembling, operating, and maintaining the Water entering a power tool will increase the risk of product.

  • Page 3: Safety Instructions For Mitre Saws

    cutting, start the motor, press the saw head down ■ Do not use the power tool if the switch does not turn and push the saw through the workpiece. Cutting on it on and off. Any power tool that cannot be controlled the pull stroke is likely to cause the saw blade to climb with the switch is dangerous and must be repaired.

  • Page 4: Additional Safety Warnings

    blade. ■ Fastening screw and nuts shall be tightened using the appropriate spanner, etc. ■ Let the blade reach full speed before contacting the workpiece. This will reduce the risk of the workpiece ■ Extension of the spanner or tightening using hammer being thrown.

  • Page 5: Residual Risks

    ■ Always fix and use extension bars for workpiece support ■ When using this tool, voltage fluctuations may affect during operation. other electrical products or lighting on the same power circuit. Connect the tool to a power source with ■ Never alter of modify the product or its function.

  • Page 6: Know Your Product

    before removing the work piece or off-cuts, or before KNOW YOUR PRODUCT reaching into the area of the blade. See page 10-11. Before first use, ensure that the angle of the bevel or mitre 1. Handle, insulated gripping surface set on the product matches the angle to be produced on 2.

  • Page 7: Transportation And Storage

    WARNING SYMBOL Do not attempt to disassemble the blade guard assembly for cleaning or repair. Damaged guards should not be Safety alert used. Return to an authorised service centre for repair or replacement. European Conformity Mark WARNING British Conformity Mark For greater safety and reliability, all repairs should be performed by an authorised service centre.

  • Page 8: Symbols In This Manual

    Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. SYMBOLS IN THIS MANUAL Plug in the product. Unplug the product. Lock Unlock Locking mechanism is not working A sound is heard Waiting time for blade to reach full speed or stop completely.
  • Page 9 6 mm 10 mm 5 mm...
  • Page 18 0˚/15˚/22.5˚/ 30˚/45˚...
  • Page 20 0˚/15˚/22.5˚/ 30˚/45˚...
  • Page 27 90˚ 90˚ 0˚ 90˚ 90˚ =90˚ ≠90˚...
  • Page 28 90˚ 90˚ 0˚...
  • Page 29 90˚...
  • Page 30 45˚ 0˚...
  • Page 31 =45˚ ≠45˚...

  • Page 36: Product Specifications

    NOISE LEVEL WARNING Mitre saw The declared noise emission value(s) have been measured Model EMS216L in accordance with a standard test method of EN 62841-1 Net weight 14.1 kg and EN 62841-3-9, and may be used for comparing one tool with another.

  • Page 37: Ec Declaration Of Conformity

    BS EN IEC 63000:2018 washers, impact wrench pins & springs, etc. For servicing, the product must be sent or presented to a RYOBI authorised service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation.
  • Page 40 BACK PAGE Techtronic Industries GmbH Max-Eyth-Straße 10, 71364 Winnenden, Germany Techtronic Industries (UK) Ltd Parkway Marlow Bucks SL7 1YL 20230426v13...

Table of Contents