Table of Contents
Advertisement
Notice
Copyright
© Agilent Technologies, Inc. 2003.
Revision
Revision 1.0, October 2003
Printed in Germany
Agilent Technologies, Deutschland GmbH
Herrenberger Str. 130
71034 Boeblingen, Germany
Warranty
The material contained in this document is provided
"as is," and is subject to being changed, without
notice, in future editions. Further, to the maximum
extent permitted by applicable law, Agilent disclaims
all warranties, either express or implied, with regard
to this manual and any information contained herein,
including but not limited to the implied warranties of
merchantability and fitness for a particular purpose.
Agilent shall not be liable for errors or for incidental
or consequential damages in connection with the
furnishing, use or performance of this document or
of any information contained herein. Should Agilent
and the user have a separate written agreement with
warranty terms covering the material in this document
that conflict with these terms, the warranty terms in
the separate agreement shall control.
Services and Support
Any adjustment, maintenance, or repair of this
product must be performed by qualified personnel.
Contact your customer engineer through your local
Agilent Technologies Service Center. Y ou can find
a list of local service representatives on the Web at:
http://www.agilent.com/find/techsupport
2
Technology Licenses
The hardware and/or software described in this
document are furnished under a license and may
be used or copied only in accordance with
terms of such license.
Restricted Rights Legend
If software is for use in the performance of a
U.S. Government prime contract or subcontract,
Software is delivered and licensed as "Commercial
computer software" as defined in DFAR 252.227-7014
(June 1995), or as a "commercial item" as defined
in FAR 2.101(a) or as "Restricted computer software"
as defined in FAR 52.227-19 (June 1987) or any
equivalent agency regulation or contract clause.
Use, duplication or disclosure of Software is subject
to Agilent Technologies' standard commercial license
terms, and non-DOD Departments and Agencies of
the U.S. Government will receive no greater than
Restricted Rights as defined in FAR 52.227-19(c)(1-2)
(June 1987). U.S. Government will receive no greater
than Limited Rights as defined in FAR 52.227-14
(June 1987) or DFAR 252.227-7015 (b)(2) (November
1995), as applicable in any technical data.
Safety Summary
General Safety Precautions
The following general safety precautions must be
observed during all phases of operation of this
instrument. Failure to comply with these precautions
or with specific warnings elsewhere in this manual
violates safety standards of design, manufacture,
and intended use of the instrument.
Agilent Technologies Inc. assumes no liability for
the customer's failure to comply with these
requirements.
Before operation, review the instrument and manual
for safety markings and instructions. You must follow
these to ensure safe operation and to maintain the
instrument in safe condition.
impaired if it is used in a manner not specified in
Environmental Conditions
This instrument is intended for indoor use in an
installation category II, pollution degree
2 environment. It is designed to operate within
a temperature range of 5 – 40 °C (40 – 105 °F)
at a maximum relative humidity of 95% and
at altitudes of up to 2000 meters.
Refer to the specifications tables for the ac mains
voltage requirements and ambient operating
temperature range.
Ground the Instrument
To minimize shock hazard, the instrument chassis
and cover must be connected to an electrical
protective earth ground. The instrument must be
connected to the ac power mains through a
grounded power cable, with the ground wire firmly
connected to an electrical ground (safety ground)
at the power outlet. Any interruption of the
protective (grounding) conductor or disconnection
of the protective earth terminal will cause a
potential shock hazard that could result in
personal injury.
Do Not Operate in an Explosive Atmosphere
Do not operate the instrument in the presence of
Do Not Remove the Instrument Cover
Operating personnel must not remove instrument
covers. Component replacement and internal
adjustments must be made only by qualified
personnel.
Instruments that appear damaged or defective
should be made inoperative and secured against
unintended operation until they can be repaired by
qualified service personnel.
General
This product is a Safety Class 1 instrument
(provided with a protective earth terminal).
The protective features of this product may be
the operation instructions.
All Light Emitting Diodes (LEDs) used in this
product are Class 1 LEDs as per IEC 60825-1.
Before Applying Power
Verify that all safety precautions are taken.
The power cable inlet of the instrument
serves as a device to disconnect from the
mains in case of hazard.
The instrument must be positioned so that
the operator can easily access the power
cable inlet. When the instrument is rack-
mounted the rack must be provided with
an easily accessible mains switch.
flammable gases or fumes.
Advertisement
Table of Contents
