Page 2
Thank you for purchasing the LW1000P Series Color Wireless Series Surveillance System. Lorex is committed to providing our customers with a high quality, reliable security product. http://www.lorexcctv.com Wireless Disclaimer: This product broadcasts over public airways and its video and audio signals may be intercepted without your consent.
Important Safeguards Important Safeguards In addition to the careful attention devoted to quality standards in the manufacture process of your video product, safety is a major factor in the design of every instrument. However, safety is your responsibility too. This sheet lists important information that will help to assure your enjoyment and proper use of the video product and accessory equipment.
Page 4
Important Safeguards Service 19. Cleaning - Unplug the video product from the 13. Servicing - Do not attempt to service this wall outlet before cleaning. Do not use liquid video equipment yourself as opening or cleaners or aerosol cleaners. Use a damp removing covers expose...
General Precautions General Precautions 1. All warnings and instructions of this manual should be followed 2. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents. Use a water dampened cloth for cleaning 3. Do not use this unit in extremely humid or wet places (i.e. Restaurant Kitchen, inside a Sauna, etc.) 4.
Features Features ‘EWT’ Eliminates Interference From Most Household Devices Fast & Easy Installation- Plug Into any AC Outlet Receiver Connects to any TV/VCR/DVD Recorder Indoor / Outdoor Night Vision Camera Built-in Microphone for Listening Ability Camera can be Battery Operated Up to 300ft Wireless Transmission Range* Night Vision Allows for Low Light Viewing.
Getting Started Getting Started The LW1010P, LW1012P, LW1020P and LW1022P come with the following components: 1 x WIRELESS RECEIVER WIRELESS CAMERA POWER ADAPTOR (FOR CAMERA) 1 x RCA VIDEO CABLE 1 x POWER ADAPTOR CAMERA BATTERY (FOR RECEIVER) ADAPTOR CABLE 1 x USB CABLE Quantity of contents for each model is as follows: Model...
Page 8
Wireless Receiver Wireless Receiver NOTE: The USB Port is ONLY on the LW1020P and LW1022P Models. 1. DC 9V INPUT (5V for LW1020P /LW1022P) – Connection port for the 9V Power Adaptor (provided with this system). Connect the Power Adaptor to a power source.
Control Buttons Control Buttons 1. AUTO BUTTON – When the receiver is set to AUTO Mode, it will continuously switch between connected cameras. The dwell time is set to 4 seconds per camera (by default), however this can be adjusted to 2~30 seconds.
Camera Installation Camera Installation Before you install the camera(s), carefully plan where and how it will be positioned, and where you will route the cable that connects the camera to the power adaptor or battery adaptor. Installation Warnings: Aim the Cameras to best optimize the viewing area: Select a location for the camera that provides a clear view of the area you want to monitor, which is free from dust, and is not in line-of-sight to a strong light source or direct sunlight.
Page 11
Camera Installation Wall Mounting Instructions To mount the camera to a wall: 1. Loosen the screw located on the side of the camera base using a slot head screwdriver. 2. Pull the camera free from the Stand. 3. Mount the stand to the wall: Mark the position of the two screw holes on the wall.
Connecting Camera Power Optimizing the Wireless Signal In order to provide the best possible video transmission, you will need to adjust the antenna of the camera and receiver as follows. Patch Antenna 1. Position the receiver’s patch antenna to face the general direction of the Hinges camera 2.
Troubleshooting Troubleshooting If you have problems with your System, there is often a quick and simple solution. Please try the following: Problem Solution (for LW1010P, LW1012P, LW1020P, (for LW1010P, LW1012P, LW1020P, and LW1022P) and LW1022P) There is no picture from a Check all connections to the Camera.