Summary of Contents for Baby Lock Pro-Stitcher Lite BLPS-LITEG-VF
Page 1
Installation Guide Gallant Machine on Villa Frame BLPS-LITEG-VF BEFORE YOU BEGIN 3D INTERACTIVE INSTRUCTIONS DOWNLOAD THE FREE APP F O R T H I S P R O D U C T C A N B E F O U N D I N...
Page 2
This document is not warranted to be error-free. Pro-Stitcher assumes no responsibility or liability for any errors or inaccuracies that may appear in the informational content contained in this manual. Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 1...
Getting Started with Pro-Stitcher Lite ............26 Update the Pro-Stitcher Lite Software............27 Downloading the Updated Pro-Stitcher Lite Software Version ..............27 Updating Pro-Stitcher Lite on the Tablet ......................28 Troubleshooting .................... 31 2 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 3...
Page 5
• If the system malfunctions or needs adjustment, first check the troubleshooting chart in the appendix to inspect and adjust the system yourself. • If unable to fix, contact your local retailer. 4 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
Page 6
été formées et encadrées sur l’utilisation de cet appareil par une personne responsable de leur sécurité. • Utilisez uniquement le cordon d’alimentation fourni par le fabricant ou une pièce de rechange certifiée par le fabricant. Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 5...
Page 7
Pour réparer ou régler la machine • Si la machine tombe en panne ou doit être réglée, consultez d’abord les consignes de dépannage figurant en annexe pour inspecter et régler vous-même la machine. 6 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
If you do not pack the system properly or if you do not use the correct packaging materials, the system could be damaged. Pro-Stitcher is not liable for damage that occurs during return shipping. Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 7...
Page 9
5. Power on the tablet as normal. NOTE: The above instructions may not apply to your particular Pro-Stitcher tablet. If you cannot solve the issue following these instructions, please contact Pro-Stitcher’s technical support. 8 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
E. Pro-Stitcher Lite Tray Assembly (without carriage): QM50000 Screws and washers: QM10170 (screws) QM12015 (screw) - circled QM10302 (washer) F. Tablet bracket: QM50000-2 G. Bracket mounting screws QM11097 Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 9...
Page 11
Design Area Size Jump (purple dotted line) not stitched Rulers Pan Scroll Bars Design End Point Design Start Point (red) (green) www.ProStitcher.com April 2023 Pro-Stitcher Lite Quick Reference Guide 10 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
Page 12
P-clip, 1/4 inch, nylon QM10291 Washer QM13246 Screw QM10945 Hex Key L 3mm (not pictured) QM10287 Hex Key L 2.5mm (not pictured) QM10286 Q. 8-Foot Villa Frame Table Top Kit-PS QF01501-PSL Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 11...
Do not remove these screws. They are keeping the tracks aligned in position. 12 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
NOTE: The four smaller inserts in the Y-rack are used to fasten it to the machine. U CAUTION: Be careful not to overtighten the screws as the base plate inserts can strip easily. Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 13...
Table Top Kit but are also included on page 15. If you have the Villa Frame set up and the Table Top Kit is assembled, go to page 16. 14 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
1. Place the carriage on the frame tracks, aligning wheels with the tracks, with the carriage encoder and power cord receptacle at the rear of the frame. engaged gears round part on levers front rear 16 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
Page 18
Flexirack by rolling the carriage along the entire length of the table. Adjust as necessary to ensure the Flexirack and the gear are aligned. black gear blue Flexirack Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 17...
Page 19
3/32-inch drill bit (see Parts List, item D), and then use a Phillips screwdriver to fasten the clamps on both sides of the Flexirack to the table. 18 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
NOTE: You will need to lift the rear wheel up and over the back wheel stop in order to access the two rear screws. Have a second person stabilize the machine while you make the adjustment. Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 19...
 IMPORTANT: Do not plug the power cord into the wall outlet until all connecting cords have been plugged in. communication cable figure 3 cable cable communication cable machine encoder carriage encoder power 20 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
X (left/right) and the Y (front/back) directions and that the corresponding gears are rotating as well. Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 21...
4. Replace the front top cover and screws, and exits cover here tighten the screws firmly with a 3mm hex wrench. 22 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
Page 24
USB cable of the tablet. port left side of tablet right side of tablet Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 23...
Tap the screen to turn on the screen again. It may be necessary to drag a finger upward on the start-up screen to access Pro-Stitcher Lite. 24 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
If your tablet is running slowly, is constantly running on a low battery, is showing signs of wear, or was purchased more than 5 years ago, you may want to think about replacing your tablet. Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 25...
 IMPORTANT: It is not necessary to power down Pro-Stitcher Lite to install or remove the USB flash drive, but take care not to remove the flash drive while the system is saving to or loading from the drive. 26 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
6. After the file is copied to the USB drive, safely remove the USB drive from the computer and plug it into the open USB port on the Pro-Stitcher Lite tablet. Check for a new software version every few weeks and update your Pro-Stitcher Lite software as needed. Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 27...
NOTE: If prompted, follow steps 6 through 13. Otherwise, proceed to step 14. 6. When the Visual C++ Redistributable installer appears, select the “I agree” box and then select Install. 28 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
Page 30
10. Wait until the installation finishes. This may take several minutes. 11. If you receive a message asking you to close some programs, select No. Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 29...
Page 31
Pro-Stitcher Lite carriage. Keep everything off for at least 1–2 minutes after an update. To complete the installation process, turn on the carriage, the machine, and the tablet again. 30 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
Make sure the encoder wheels roll on the tracks when moving the quilting machine and that the stitch regulator cable is plugged in securely to the encoders. Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 31...
Page 33
Do not use a solvent-based or an oil-based lubricant (such as WD-40 or sewing machine oil), as this will attract dust and eventually clog the gears. 32 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
Page 34
If it opens but there are no files on the flash drive, contact Pro-Stitcher for replacement files.* *Pro-Stitcher highly recommends backing up all pattern files on a home computer or another disk. Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 33...
Page 35
A mouse may be plugged in to an available USB port and used to save any work prior to rebooting the tablet. 34 | Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame www.ProStitcher.com...
Page 36
Windows blue/white screen) if you do not select the Start Normally option in time. If this occurs, use the power switch to reboot the computer and try again. Pro-Stitcher Lite for the Baby Lock Gallant/Villa Frame Installation Instructions | 35...