Baby Lock Pearl BLQF Assembly Instructions Manual
Baby Lock Pearl BLQF Assembly Instructions Manual

Baby Lock Pearl BLQF Assembly Instructions Manual

Quilt frame

Advertisement

1

Advertisement

Table of Contents
loading

Summary of Contents for Baby Lock Pearl BLQF

  • Page 2: Table Of Contents

    Step 17- Attach Leaders Step 18- Adjusting Frame Height and Leveling What’s Included Your Baby Lock Pearl Frame is delivered in three separate boxes. Upon opening, please check immediately to see if you have received the items listed in the Parts and Hardware lists found on pages 3, 4 and 5.
  • Page 3: Parts & Hardware List

    Baby Lock Pearl Frame Parts & Hardware List Left Pole Right Pole Bracket Bracket Assembly (1) Assembly (1) (Comes with latches QF05300-100 Pole Coupler not assembled) Pole Section, 5’ QF05300-200 QF05300-701 QF09318-702 Table Section with Plastic Top Table Splice (2)
  • Page 4 QF09318-202 QF09318-105 QF09318-106 Baby Lock Pearl Frame Parts & Hardware List QF09318-204 RATCHET STOP MOUNT QF09318-105 SHING RAIL BEARING SNAP RAIL BEARING SNAP COVER CONNECTOR BOLT Fig. 10-2 QF09318-713 QF09318-705 8-703 HAND WHEEL COLLAR Bungee Clamps (4) Upper Middle Leg (1)
  • Page 5 Baby Lock Pearl Frame Parts & Hardware List Pole End Assembly with Long Pole End Assembly (5) Pole End Assembly with Short Bolt (1) Bolt (2) QF09326 QF09321 QF09320 Hand Wheel Assembly (1) QF09325 Hand Wheel Insert (1) V-Groove Bearing (8)
  • Page 6: Step 1- Remove Track Supports

    Step 1 Remove Track Supports Fig. 1-1 Step 1: Remove Track Supports 1-2: Using the 4mm Allen wrench remove the Parts needed three screws from each track support and set 2-Table Section the track support aside in a safe place (Fig.
  • Page 7: Step 2- Table Assembly

    Step 2 Table Assembly Fig. 2-1 Step 2: Table Assembly Parts needed 2-Table Section 2-Table Splice 12- M8x16mm Socketed Button Head Cap Screw QF09318-07 Tools Required 5mm Allen Wrench (provided) 2-1: With the table sections face down (large round screw holes for track supports up), slide the two table sections together end to end, as close as possible.
  • Page 8: Step 3- End Leg Assembly

    Step 3 End Leg Assembly Upper Leg B Upper Leg A Height-Adjustment Upper Holes Leg A Fig. 3-1 Upper Leg B Detail 3-1 Step 3: End Leg Assembly 3-2: Attach each upper end leg to the table Parts needed with two (2) M8x16mm screws through the 1-Table Assembly upper corner leg brackets at front or rear and 2-Upper End Leg A...
  • Page 9: Step 3- End Leg Assembly

    Step 3 End Leg Assembly (continued) Detail 3-3 Fig. 3-3 3-3: Slide one (1) lower corner leg onto the two (2) upper corner legs on each end of the frame as shown in Fig. 3-2 on the previous page and Fig. 3-3. Choose the preferred height of the frame based on the table in Fig.
  • Page 10 Step 3 Corner Leg Assembly (continued) Detail 3-4 Fig. 3-5 Detail 3-5 3-4: Thread a leveling glide into each end of the corner leg assemblies, leaving about 1/2” of the threads exposed to make it easier to level the frame later. (Fig. 3-5 and Detail 3-5)
  • Page 11: Step 4- Middle Leg Assembly

    Step 4 Middle Leg Assembly Fig. 4-1 Step 4: Middle Leg Assembly Parts needed 1-Table Assembly 1-Upper Middle Leg 1-Lower Middle Leg 5-M8x16mm Socketed Button Head Cap Screw QF09318-07 1-M8 Nylon Washer QF05300-157 2-Leveling Glide Tools Required 5mm Allen Wrench 4-1: Place the upper middle leg on the center of the table assembly and thread an M8x16mm QF09318-07 into each corner of the mounting...
  • Page 12 Step 4 Middle Leg Assembly (continued) Fig. 4-2 4-2: Slide the lower middle leg onto the upper middle leg, and insert an M8x16mm QF09318- 07 with nylon washer QF05300-157 into the same height setting as the corner legs. Fully tighten the M8x16mm QF09318-07 with the 5mm Allen wrench.
  • Page 13 Step 5 Uprighting the Frame Fig. 5-1 Step 5: Uprighting the Frame Parts needed 1-Frame Assembly Tools Required Helper NOTE: The end screws have been temporarily installed and lightly tightened into the end of the frame to support the legs while uprighting it.
  • Page 14: Step 6- Support Rail Assembly

    Step 6 Support Rail Assembly Fig. 6-1 Note the orientation of the support rail to the end leg. Step 6: Support Rail Assembly Parts needed 1-Frame Assembly 2-Support Rail 8-M8x25mm Socketed Button Head Cap Screw QF09318-06 (already in frame ends) Remove these lightly- tightened end M8x- Tools Required...
  • Page 15: Step 7- Track Assembly

    Step 7 Track Assembly Place the track support upside down with the lip toward the outside of the table. Third Hole for QF09318-02 stop screws Second Hole Fig. 7-1 Fig. 5-1 First Hole Track Support shown upside down. Step 7: Track Assembly Stop Screws M5 x 8mm SBHCS QF09318-304 in Third Hole Fig.
  • Page 16: Step 7- Track Assembly

    Step 7 Track Assembly (continued) Insert the other end of the coupler into second prepared track support section. Hold the two adjoining track support sections tightly together and thread an M5x8mm QF09318-304 into the first hole of the second track support and lightly tighten.
  • Page 17 Step 7 Track Assembly (continued) Detail 7-5 Fig. 7-5 Place the machine onto the carriage 7-9: and again, roll it the entire length of the frame, working the tracks into the wheels as you go. Lightly tighten the front track support screws as you move down the table.
  • Page 18: Step 8- Ratchet Stop Assembly

    Step 8 Ratchet Stop Assembly Stop Holder Mount QF09318-204 Screw Bushing Fig. 8-1 Step 8: Ratchet Stop Assembly 8-4: Following the parts order shown in Parts needed Fig. 8-1, thread one M6 x 48mm QF09318-204 1-Open-hole Pole Bracket (right) through a ratchet-stop, ratchet-stop bushing, 3-M6x48mm Socketed Washer Head Cap Screw pole bracket (with ratchet-stop holder inserted) QF09318-204...
  • Page 19 Step 8 Ratchet Stop Assembly (continued) Finger Detail 8-1a Detail 8-1b Detail 8-1c...
  • Page 20: Step 9- Pole Bracket Assembly

    Step 9 Pole Bracket Assembly Detail 9-2 Center Hole Top Hole Fig. 9-1 Detail 9-1 Step 9: Pole Bracket Assembly Parts needed the inside of the frame. (Other holes are 1-Frame Assembly normally not used but were included to allow 1-Pole Bracket Assembly with Latches (right) future height adjustment if needed).
  • Page 21: Step 10- Pole Coupler Assembly

    Step 10 Pole Coupler Assembly Fig. 9-2 Fig. 9-1 Fig. 9-3 Step 10: Pole Coupler Assembly Parts needed Pole Section 8-Pole Sections 4-Pole Couplers 10-1: Join two pole sections together by inserting a pole coupler into the end of one pole Pole Coupler section (as shown in Fig.
  • Page 22 Step 11 Push Loosen Nut Pole End Assembly Step 11: Pole End Assembly Parts needed 4-Pole Assembly 5-Pole End Fig. 8-1 2-Short-Bolt Ratchet Wheel Assembly 1-Long-Bolt Ratchet Wheel Assembly 1-Hand Wheel Assembly 1-Hand Wheel Insert Wedge Tools Required Fig. 11-1 Fig.
  • Page 23: Step 11- Pole End Assembly

    Step 11 Pole End Assembly (continued) Batting Storage Pole Fig. 9-6 Fig. 9-6 Fig. 11-5 11-7: Repeat steps 11-5 and 11-6 to add a Inside Pole End Short Bolt Wedge second pole end to the other open end of the Short Bolt Wedge pole assembly just built and one pole end to Outside Pole End...
  • Page 24 Step 11 Quilt-Top Pole Backing Pole Pole End Assembly (continued) Take-up Pole Fig. 9-6 Fig. 9-6 Fig. 9-6 Fig. 9-6 Fig. 11-9 11-13: Repeat Step 11-10 to prepare the long-bolt ratchet wheel assembly for insertion. Ratchet Wheel and Hand Wheel Insertion 11-14: Insert one short-bolt ratchet wheel Fig.
  • Page 25: Step 12- Batting Bar Bracket Assembly

    Step 12 Batting Bar Bracket Assembly Initial height set approximately at center of upper leg. Step 12: Pole End Assembly Cutout Parts needed height 2-Batting Bar Bracket Assembly fixing 2-Batting Bar Bracket Clamp screw. 8- M6x25mm Socketed Washer Head Cap Screw QF05300-113 Tools Required M4 Allen Wrench (provided)
  • Page 26: Step 13- Pole To Frame Assembly

    Steps 13 & 14 Pole to Frame Assembly Take-Up Pole Rubber End Cap Assembly Quilt-Top Pole Backing Pole Batting Storage Pole Fig. 13-1 Step 13: Pole to Frame Assembly Parts needed 1-Frame Assembly 1-Batting Storage Pole 1-Quilt-Top Pole 1-Backing Pole 1-Take-up Pole 13-1: Place the poles on the frame as shown in Fig.
  • Page 27: Step 15- Bungee Clamp Assembly

    Steps 15 & 16 Bungee Clamp Assembly Hook & Loop Tape on Pole Assemblies Step 15: Bungee Clamp Assembly Parts needed 1- Frame Assembly 4- Bungee Clamps QF09318-110 15-1: Thread the bungee clamp cord from the inside of the frame through the bungee slot and then pull the cord in a downward movement to lock the bungee clamp into place.
  • Page 28: Step 17- Attach Leaders

    Steps 17 & 18 Attach Leaders Adjusting Frame Height and Leveling Step 17: Attach Leaders Parts needed bent at a 90 degree angle. It is recommended 1-Frame Assembly with hook & loop tape to have a second person lift the frame weight applied to Poles off the height adjusting screws when you need 3- Leaders (Sold separately BLQL)

Table of Contents