Table of Contents
Advertisement
RECIRCULATING
C
INSTALLATION OVERVIEW
C1. Attach Mounting Plate to Wall
C2. Prepare Top Cabinet
C3. Check Blower Plate
C4.
Mount the Microwave Oven
Install or change Charcoal Filter
C5.
IMPORTANT NOTES:
•
Make sure the screws for the blower motor and blower
plate are securely tightened when they are reinstalled.
This will help to prevent excessive vibration.
•
Make sure the motor wiring has been properly routed
and secured, and that the wires are not pinched.
C1.
ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
NOTE:
If the cabinet depth including the cabinet doors
is more than 13" " ' ' then the unit must be spaced
out from wall using adequate materials supporting
150 Ibs to allow proper top vent air exhaust/intake.
Cabinet
Installation Instructions
(Non-Vented Ductless)
Cabinet
EN-20
3/8" TO EDGE
along the dotted line.
Trim the rear wall template
12"
TO
NOTE: IT IS VERY IMPORTANT
READ AND FOLLOW
THE DIRECTIONS
IN THE INSTALLATION
INSTRUCTIONS
BEFORE PROCEEDING
WITH THIS
REAR WALL TEMPLATE.
serves to position the bottom
4"
mounting plate and to locate
This Rear Wall Template
the horizontal exhaust
1. Use a level to check
outlet.
that the template is positioned
accurately.
one stud on the left or
2. Locate and mark at least
right side of the centerline.
least one wood
It is important to use at
a stud to support the weight
screw mounted firmly in
two additional, evenly spaced
of the microwave. Mark
toggle bolts.
3. Drill holes in the marked
locations for the supplied
locations. Where there
is
a stud, drill a 3/16" hole
for wood screws. For holes
that do not line up with
a stud, drill 5/8" holes for
toggle bolts.
DO NOT INSTALL THE
MOUNTING PLATE
AT THIS TIME.
4. Remove the template
Instruction book for your
from the rear wall.
5. Review the Installation
installation situation.
para consultar la
Darle vuelta a la hoja
versión en Español.
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE.
FOR 2 ADDITIONAL,
EVENLY
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
to align with holes in the
AREA.
Locate and mark holes
mounting plate.
LOCATE AT LEAST ONE
IMPORTANT:
STUD ON EITHER SIDE
OF
THE CENTERLINE.
MARK THE LOCATION
FOR 2 ADDITIONAL,
EVENLY
along the dotted line.
SPACED TOGGLE BOLTS
IN THE MOUNTING PLATE
Trim the rear wall template
AREA.
1
Remove the toggle wings from the bolts.
2
Insert the bolts into the mounting plate through
the holes designated to go into drywall and
reattach the toggle wings to
each bolt.
To use toggle bolts:
Spacing for Toggles
More Than Wall
Thickness
Toggle Wings
Mounting
Toggle
Plate
Bolt
Wall
3
Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bott m of the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
4
to help tighten the bolts.
3
⁄
" (19 mm) onto
4
Bolt End
o
Advertisement
Table of Contents
