Table of Contents
Advertisement
OUTSIDE BACK EXHAUST
B
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
PREPARING THE REAR WALL
B1.
FOR OUTSIDE BACK EXHAUST
You need to cut an opening in the rear wall for
outside exhaust.
NOT E:
READ
IT IS VERY
AND FOLL
IMPO RTAN
IN THE
OW THE
T TO
BEFO
INST ALLA
DIRE CTIO
RE PRO
TION INST
NS
REAR
WAL L
CEED
ING WITH
RUC TION
TEM PLAT
S
This Rear
Wall Templa
E.
THIS
3/8" TO EDGE
mounti
ng plate
te serves
outlet.
and to
locate the
to positio
12"
1. Use
horizon
n the bottom
accura
a level
to check
tal exhaus
2. Locate
tely.
that the
t
and mark
templa
te is positio
right side
at least
ned
of the centerl
one stud
on the
4"
screw mounte
I t is importa
ine.
left or
of the microw
d firmly
nt to use
at least
ave. Mark
in a stud
one wood
locatio ns
for the
two additio
to suppor
t the weight
3. Drill
holes in
supplie
d toggle
nal, evenly
a stud,
the marked
bolts.
spaced
that do
drill a 3/16"
locatio ns.
not line
hole for
wood screws
Where
there is
toggle
bolts.
up with
a stud,
. For holes
D O NOT
drill 5/8"
holes for
AT THIS
INSTA LL
4. Remov
TIME.
THE MOUN
5. Review
e the templa
TING PLATE
the Installa
te from
the rear
installa
tion situatio
tion Instruc
wall.
n.
tion book
for your
Darle vuelta
versió n
a la hoja
en Españ
ol.
para consu
ltar la
Loca te
and mark
moun ting
holes to
plate .
align with
IMPO RTAN
holes in
T:
the
LOCA
TE AT
THE CEN
LEAS T
TERL INE.
ONE STUD
MAR K
ON EITH
THE LOCA
ER SIDE
SPAC
TION FOR
OF
ED TOG
GLE BOLT
2 ADD
AREA
.
ITION AL,
S IN THE
EVEN
MOU NTIN
LY
G PLAT
E
Trim the
rear wall
temp late
along
the dotte
d line.
Loca te
and mark
moun ting
holes to
plate .
IMPO RTAN
T:
LOCA
TE AT
LEAS T
THE CEN
MAR K
TERL INE.
THE LOCA
SPAC
ED TOG
AREA
GLE BOLT
.
•
Read the instructions on the REAR
WALL TEMPLATE.
•
Tape it to the rear wall.
•
Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
Installation Instructions
NOTE: IT IS VERY IMPORTANT
TO
READ AND FOLLOW
THE DIRECTIONS
INSTRUCTION S
IN THE INSTALLATION
WITH THIS
BEFORE PROCEEDING
REAR WALL TEMPLATE.
This Rear Wall Template
serves to position the bottom
the horizontal exhaust
mounting plate and to locate
outlet.
1. Use a level to check
that the template is positioned
accurately.
one stud on the left or
2. Locate and mark at least
right side of the centerline.
It is important to use at
least one wood
a stud to support the weight
screw mounted firmly in
of the microwave. Mark
two additional, evenly spaced
toggle bolts.
locations for the supplied
locations. Where there is
3. Drill holes in the marked
a stud, drill a 3/16" hole
for wood screws. For holes
a stud, drill 5/8" holes for
that do not line up with
toggle bolts.
DO NOT INSTALL THE
MOUNTING PLATE
AT THIS TIME.
4. Remove the template
from the rear wall.
Instruction book for your
5. Review the Installation
installation situation.
para consultar la
Darle vuelta a la hoja
versión en Español.
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
OF
STUD ON EITHER SIDE
LOCATE AT LEAST ONE
THE CENTERLINE.
FOR 2 ADDITIONAL,
EVENLY
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
along the dotted line.
Trim the rear wall template
Trim the
rear wall
temp late
along
the dotte
d line.
align with
holes in
the
ONE STUD
ON EITH
ER SIDE
TION FOR
OF
2 ADD
ITION AL,
S IN THE
EVEN
MOU NTIN
LY
G PLAT
E
(Horizontal Duct)
3/8" TO EDGE
along the dotted line.
Trim the rear wall template
12"
4"
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
OF
LOCATE AT LEAST ONE
STUD ON EITHER SIDE
THE CENTERLINE.
FOR 2 ADDITIONAL,
EVENLY
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
REMOVE BLOWER PLATE
B2.
Remove and save the screw that holds the blower
plate to the microwave. Lift off the blower plate.
Blower Plate
EN-16
Back of
Microwave
Advertisement
Table of Contents
