Locknut (rocker arm adjusting
screw)
27 Nm (2.7 m·kgf, 20 ft·lbf)
e. Measure the valve clearance again.
f. If the valve clearance is still out of specifica-
tion, repeat all of the valve clearance adjust-
ment steps until the specified clearance is
obtained.
▲
▲▲▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
13.Install:
• Rear cylinder tappet covers
• Fuel filter bracket
• Front cylinder tappet covers
Rear cylinder tappet cover bolt
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Front cylinder tappet cover bolt
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
14.Install:
• Crankshaft end accessing screw
(along with the O-ring
• Timing mark accessing screw
(along with the O-ring
• Generator cover damper
• Damper cover
Refer to "GENERATOR AND STARTER
CLUTCH" on page 5-42.
Damper cover bolt
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
15.Install:
• All removed parts
TIP
For installation, reverse the removal procedure.
EAS21070
CHECKING THE CRANKCASE BREATHER
HOSE
1. Remove:
• Air filter case
Refer to "GENERAL CHASSIS" on page 4-1.
• Air duct
Refer to "BELT DRIVE" on page 4-94.
• Fuel tank
Refer to "FUEL TANK" on page 6-1.
2. Check:
• Crankcase breather hose "1"
Cracks/damage → Replace.
Loose connection → Connect properly.
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
New
)
New
)
PERIODIC MAINTENANCE
ECA13450
NOTICE
Make sure the crankcase breather hose is
routed correctly.
▲▲▲
3. Install:
• Fuel tank
Refer to "FUEL TANK" on page 6-1.
• Air duct
Refer to "BELT DRIVE" on page 4-94.
• Air filter case
Refer to "GENERAL CHASSIS" on page 4-1.
EAS20570
SYNCHRONIZING THE THROTTLE BODIES
TIP
Before synchronizing the throttle bodies, check
the following items:
• Valve clearance
• Spark plugs
• Air filter element
• Throttle body joints
• Fuel hoses
• Exhaust system
• Breather hoses
1. Stand the vehicle on a level surface.
TIP
Place the vehicle on a suitable stand.
2. Check:
• Engine idling speed
▼
▼▼▼
▼ ▼▼▼
▼
a. Start the engine, warm it up for several min-
utes, and then let it run at the specified en-
gine idling speed.
Out of specification → Clean or replace.
▲
▲▲▲
▲ ▲▲▲
▲
3. Remove:
• Air filter case
Refer to "GENERAL CHASSIS" on page 4-1.
3-7
1
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
Engine idling speed
950–1050 r/min
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▼ ▼▼▼
▼
▼▼▼
▲ ▲▲▲
▲
▲▲▲