Advertisement
Quick Links
BEFORE YOU BEGIN
HOW TO USE THESE INSTRUCTIONS
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your partic-
ular installation. This will help you avoid costly mistakes.
In addition to proper installation, read all operating and
safety instructions.
NOTES
S
Seat post holes on 5-1/2" centers.
S
Water depth from rim is 6-3/4".
S
1-3/4" passageway.
S
Ensure that the new toilet has the correct
roughing-in dimension. The K-3420-K and
K-3421-K have a 12" roughing-in dimension. See
Fig. #1.
S
Be very careful while working with vitreous china
products. Vitreous china can break and chip if
you overtighten bolts and nuts or carelessly
handle the product.
S
Carefully inspect new fixture for any sign of
damage.
S
Observe all local plumbing and building codes.
S
Shut off water supply.
S
For new construction, refer to the dimensions in
Fig. #1 and Fig. #4 for locating the shut-off valve.
S
Fixture dimensions are nominal and conform to
tolerances by ANSI Standards (A112.19.2).
WARNING: Risk of personal injury or product
damage. Handle vitreous china products very
carefully. Vitreous china can break and chip if you
over-tighten bolts and nuts.
WARNING: Risk of external leakage. The fill
valve nut has been factory-tightened to design
specifications. If re-tightening is required, wrench
tighten one turn past finger tight.
CA
114049-2-
(B)
R
1 1
WELLWORTH ECO-LITE
VITREOUS CHINA
REVERSE TRAP TOILETS
All information in these instructions is based on the latest
product information available at the time of publication.
Kohler Co. reserves the right to make changes in product
characteristics, packaging, or availability at any time with-
out notice.
These instructions contain important care, cleaning, and
warranty information – please leave instructions for the
consumer.
ORDERING INFORMATION
Wellworth Eco-Lite Toilet (elongated)
Wellworth Eco-Lite Toilet (round front)
When specified:
3/8" supply
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
5/16" floor bolts (pr.)
. . . . . . . . . . . . . . . . . . . . .
. . . . . .
K-3420-K
. . . . .
K-3421-K
K-7637
21401
E1998 Kohler Co.
Advertisement
Related Manuals for Kohler WELLWORTH ECO-LITE K-3420-K
Summary of Contents for Kohler WELLWORTH ECO-LITE K-3420-K
- Page 1 Follow the sections that pertain to your partic- Kohler Co. reserves the right to make changes in product ular installation. This will help you avoid costly mistakes. characteristics, packaging, or availability at any time with- In addition to proper installation, read all operating and out notice.
- Page 2 Page 3.) ROUGHING-IN 19-3/4” 1” FRONT OF BOWL 31-7/8” 3-5/8” 15” 9” 4-1/8” C OF OUTLET 12” 3/8” I.P.S. SUPPLY Fig. #1 .9<116 Roughing-In Notes K-3420-K/KU 29-1/2” 15-5/8” 6-1/8” 9-1/2” K-3421-K/KU 27-1/2” 14-1/8” 6-3/16” 9-3/4” Kohler Co., Kohler, WI 114049-2-...
-
Page 3: Installation
4-1/8” to the left of the centerline of the closet flange. 9” Centerline of supply shut-off outlet should extend 4” from finished wall. Install the supply shut-off valve with outlet vertical. 12” Fig. #4 Kohler Co., Kohler, WI 114049-2-... - Page 4 Overtightening may cause breakage or chipping. Washer Alternately tighten the three brass hex nuts so that the top of the tank is level with the top of the bowl and a watertight seal is obtained. Fig. #7 Kohler Co., Kohler, WI 114049-2-...
- Page 5 If the two handles are not in alignment for appearance, the Adjustment Screw alignment can be adjusted by turning the handle Long Flush adjustment screw to achieve acceptable appearance. Short Flush Chain Attachment Short Flush Attachment Fig. #10 Kohler Co., Kohler, WI 114049-2-...
- Page 6 Adjust float by sliding it up or down on float rod until water level is at the marked water line on the flush valve overflow. Float Check all connections for leaks for several days. Float Rod Fig. #11 Kohler Co., Kohler, WI 114049-2-...
-
Page 7: Troubleshooting Chart
A. Adjustment screw is not properly adjusted. A. Turn handle adjustment screw to obtain acceptable handle alignment. handle alignment. Turn screw clockwise to lower end of 1.6 flush handle. Turn screw counterclockwise to raise end of 1.6 flush handle. Kohler Co., Kohler, WI 114049-2-... -
Page 8: Important Consumer Information
Most toilet bowl cleaners are not harmful to the vitreous Kohler Company shall not be responsible or liable for any china surface of the toilet bowl. Please follow the bowl damage to these tank fittings caused by the use of cleaner manufacturer’s instructions carefully.