Table of Contents
Advertisement
RADIO SYSTEM CONTROLS
USING THE RADIO SYSTEM
The TQi Radio System has been pre-adjusted at the factory. The
adjustment should be checked before running the model, in case of
movement during shipping. Here's how:
1. Turn the transmitter switch on. The status LED on the transmitter
should be solid green (not flashing).
2. Elevate the model on a block or a stand so that all the tires are
off the ground. Make sure your hands are clear of the moving
parts of the model.
3. Plug the battery pack in the model into the speed control.
The model is now ON.
4. Turn the steering wheel on the transmitter back and forth and
check for rapid operation of the steering servo. Also, check that
the steering mechanism is not loose or binding. If the steering
operates slowly, check for weak batteries.
5. When looking down at the model, the front wheels should be
pointing straight ahead. If the wheels are turned slightly to the
left or right, turn off TSM (see page 25) and slowly adjust the
steering trim control on the transmitter until they are pointing
straight ahead; then, return the multi-function knob to the
desired TSM setting.
TRAXXAS TQ
6. Gently operate the throttle trigger to ensure that you have
forward and reverse operation, and that the motor stops when
the throttle trigger is at neutral. WARNING: Do not apply full
throttle in forward or reverse while the model is elevated.
7. Once adjustments are made, unplug the model first, and then
turn off the transmitter.
Range-Testing the Radio System
Before each running session with your model, you should range-test
your radio system to ensure that it operates properly.
1. Turn on the radio system and check its operation as described in
the previous section.
2. Have a friend watch the model. Make sure hands and clothing are
clear of the wheels and other moving parts on the model.
3. Walk away from the model with the transmitter until you reach
the farthest distance you plan to operate the model.
4. Operate the controls on the transmitter once again to be sure
that the model responds correctly.
5. Do not attempt to operate the model if there is any problem
with the radio system or any external interference with your radio
signal at your location.
Higher Speeds Require Greater Distance
The faster you drive your model, the more quickly it will near the
limit of radio range. At 60mph, a model can cover 88 feet every second!
It's a thrill, but use caution to keep your model in range. If you want to
see your model achieve its maximum speed, it is best to position yourself
in the middle of the model's running area, not the far end, so you drive
the model towards and past your position. In addition to maximizing the
radio's range, this technique will keep your model closer to you, making
it easier to see and control.
Your model's radio system is designed to operate reliably up to the
approximate distance that it is no longer easy or comfortable to see and
control the model. Most drivers will struggle to see and drive their model
at distances farther than a football field (300+ feet). At greater distances,
you could lose sight of your model and you may also exceed the radio
system's operating range, which will cause the failsafe system to activate.
For best visibility and control of your model, keep your model within 200
feet, regardless of the maximum range available. No matter how fast or
far you drive your model, always leave adequate space between you,
the model, and others. Never drive directly toward yourself or others.
RADIO SYSTEM
i
Using Reverse: While driving,
push the throttle trigger
forward to apply brakes.
Once stopped, return the
throttle trigger to neutral.
Push the throttle trigger
forward again to engage
proportional reverse.
Automatic Failsafe
The TQi transmitter
and receiver are equipped
with an automatic failsafe
system that does not require
user programming. In
the event of signal loss or
interference, the throttle
will return to neutral and
the steering will hold its
last commanded position. If
failsafe activates while you
are operating your model,
determine the reason for
signal loss and resolve the
problem before operating
your model again.
In order to re-acquire the
signal after the failsafe has
activated, you will need to
walk a longer distance closer
to the model than the distance
the model travelled out of
range. Simply keep walking
towards the model until you
re-acquire the signal.
5,6,7
TRAXXAS • 15
Advertisement
Table of Contents
