Advertisement
Available languages
Available languages
22 | English
– Push the glide arm (27) all the way back.
– The two articulated parts at the top of the glide arm are
now upright and closed.
– Pull the clamping lever (24) upwards until the clamping
wedge is positioned between the two articulated parts at
the bottom of the glide arm.
– This locks the glide arm (27), which is pushed all the way
back.
Glide arm pulled all the way forward:
– Pull the glide arm (27) all the way forward.
– The glide mechanism is now completely extended.
– Pull the clamping lever (24) upwards until the clamping
wedge is positioned between the two articulated parts at
the bottom of the glide arm.
When sawing mitre and/or bevel angles, you have to pull the left-hand or right-hand adjustable fence (5) outwards depending
on the cutting direction, or remove it completely.
Bevel angle
Mitre angle
0°–47°
≤ 44°
(left)
(right/left)
0°–47°
≥ 45°
(left)
(right/left)
0°–47°
≤ 44°
(right)
(right/left)
0°–47°
≥ 45°
(right)
(right/left)
Adjusting the damping of the glide arm (see figure F)
The glide mechanism of the glide arm (27) is preset at the
factory and is not damped when the power tool is delivered.
The damping of the glide mechanism can be adjusted using
the damper (52):
Hard – for more controlled work movements;
Soft – for fast saw cuts.
– For softer damping, loosen the two set screws (53) using
the hex key ( mm) (16)
– or
– tighten the two set screws (53) for harder damping.
Clamping the workpiece (see figure G)
To ensure maximum safety while working, the workpiece
must always be firmly clamped.
Do not saw workpieces that are too small to clamp firmly.
– Press the workpiece firmly against the fences (6) and (5).
– Insert the supplied screw clamp (18) into one of the cor-
responding holes (54).
– Loosen the wing bolt and adjust the screw clamp to the
workpiece. Tighten the wing bolt again.
– Tighten the threaded rod (56) to fix the workpiece in
place.
1 609 92A 5RS | (23.06.2020)
– This locks the glide arm (27), which is pulled all the way
forward.
Preparing for operation
Extending the Saw Table (see figure C)
The free end of long workpieces must have something
placed underneath it or be supported.
The saw table can be extended left and right using the saw
table extensions (7).
– Push the clamping lever (50) inwards.
– Pull out the saw table extension (7) to the required length
(maximum 250 mm).
– To lock the saw table extension in place, push the clamp-
ing lever (50) back out.
Moving the fence (see figures D–E)
– Loosen the locking screw (51).
– Pull the left-hand adjustable fence (5) all the way out.
– Loosen the locking screw (51).
– Pull the left-hand adjustable fence (5) all the way out.
– Lift the adjustable fence upwards and out of the way.
– Remove the locking screw (51).
– Loosen the locking screw (51).
– Pull the right-hand adjustable fence (5) all the way out.
– Lift the adjustable fence upwards and out of the way.
Releasing the workpiece
– To loosen the screw clamp, turn the threaded rod (56)
anticlockwise.
Setting mitre and bevel angles
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure precise cuts, the basic settings of the power tool
must be checked and adjusted as necessary after intensive
use.
Experience and suitable special tools are required for this.
A Bosch after-sales service point will handle this work
quickly and reliably.
Always tighten the locking knob (11) firmly before
u
sawing. Otherwise the saw blade can become wedged in
the workpiece.
Adjusting the horizontal mitre angle
Setting Standard Mitre Angles (see figure H)
For quick and precise setting of commonly used mitre
angles, detents (14) are provided on the saw table:
45°; 31.6°; 22.5°; 15°
Leftward
Rightward
0°
15°; 22.5°; 31.6°; 45°; 60°
Bosch Power Tools
Advertisement
