Table of Contents
Advertisement
3. Make sure that the power trigger and the power
trigger lockout moves freely and that the return
springs operate properly.
4. Start the product, refer to
page 12 .
5. Push the power trigger fully to apply full speed.
6. Release the power trigger and make sure that the
cutting attachment stops and remains still.
To do a check of the hand guard
The hand guard prevents hands from accidental contact
with the blades.
1. Stop the product.
2. Remove the battery.
3. Check that the hand guard is attached correctly.
4. Examine the hand guard for damages.
Battery safety
WARNING:
instructions that follow before you use the
product.
•
Only use the BLi200 battery. Refer to
on page 17 . The battery is software encrypted.
•
Use the BLi200 battery that is rechargable as a
power supply for the related Husqvarna products
only. To prevent injury, do not use the battery as a
power supply for other devices.
•
Risk of electrical shock. Do not connect the battery
terminals to keys, coins, screws or other metal. This
can cause a short circuit of the battery.
•
Do not use non-rechargeable batteries.
•
Do not put objects into the air slots of the battery.
•
Keep the battery away from sunlight, heat or open
flame. The battery can cause burns and/or chemical
burns.
•
Keep the battery away from rain and wet conditions.
•
Keep the battery away from microwaves and high
pressure.
•
Do not try to disassemble or break the battery.
•
If the battery leaks, do not let the liquid touch your
body or eyes. If you have touched the liquid, clean
the area with a large quantity of water and soap, and
get medical aid. If you get liquid in your eyes, do not
10
To start the product on
Read the warning
Technical data
rub but flush with water for a minimum of 15 minutes
and get medical aid.
•
Use the battery in temperatures between -10 °C (14
°F) and 40 °C (114 °F).
•
Do not clean the battery or the battery charger with
Battery information on page 12 .
water. Refer to
•
Do not use a defective or damaged battery.
•
Keep batteries in storage away from metal objects
such as nails, screws or jewelry.
•
Keep the battery away from children.
Battery charger safety
WARNING:
instructions that follow before you use the
product.
•
Risk of electrical shock or short circuit if the safety
instructions are not obeyed.
•
Do not use other battery chargers than the one
supplied for your product. Only use QC330/QC500
chargers when you charge BLi200 replacement
batteries.
•
Do not try to disassemble the battery charger.
•
Do not use a defective or damaged battery charger.
•
Do not lift the battery charger by the power cord. To
disconnect the battery charger from a mains socket,
pull out the plug. Do not pull the power cord.
•
Keep all cables and extension leads away from
water, oil and sharp edges. Make sure that the cable
is not caught between objects, for example, doors,
fences or equivalent.
•
Do not use the battery charger near flammable
materials or materials that can cause corrosion.
Make sure that the battery charger is not covered.
Pull out the plug to the battery charger if there is
smoke or fire.
•
Only charge the battery indoors in a location with
good airflow and away from sunlight. Do not charge
the battery outdoors. Do not charge the battery in
wet conditions.
•
Only use the battery charger where the temperature
is between 5 °C (41 °F) and 40 °C (104 °F). Use the
charger in an environment which has a good airflow,
dry and free from dust.
•
Do not put objects into the cooling slots of the
battery charger.
•
Do not connect the battery charger terminals to
metal objects as this can short circuit the battery
charger.
•
Use approved mains sockets that are not damaged.
Make sure that the cord of the battery charger is not
damaged. If extension cables are used, make sure
that the extension cables are not damaged.
Read the warning
1266 - 003 - 23.09.2022
Advertisement
Table of Contents
